GENIE 41557.00356 Universal Wireless Wall Console Instructions

GENIE 41557.00356 Universal Wireless Wall Console

overview

Open battery cover and remove battery tab before programming.
LED Signals:

• LED Blue blink indicates NORMAL status
• LED Red blink indicates LOW BATTERY
• LEDs will vary during programming

WARNING

• DO NOT install wall counsel unless the door operator’s safety devices work as required by the door operator’s manual.
• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.
• Keep Door in Sight at all times when door is moving.
• DO NOT allow children to play with the operator controls. If safety reverse does not work properly:
• Close door then disconnect opener using the manual release handle.
• DO NOT use transmitters or controls for door operator.
• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

THINGS TO KNOW BEFORE STARTING

• For use only with garage door operators complying with UL 325, manufactured after 1993 with working photo eyes installed.
• During programming, the garage door opener may operate. Ensure that the garage door opening is clear of personnel or any obstructions.
• Do not to press the LEARN button for longer than the noted 2-3 seconds as it could cause the existing, operational remotes and keypads to no longer work.
• All DOOR buttons are factory set to Overhead Door® CodeDodger® 1. Below are the brands and specifications that this console is compatible with. Find the ID# in Chart A below that references your specific opener specification. You will need this number during programming. Refer to STEP 1 to find the type and/or LEARN/PROGRAM button.

DIP switch models are noted with an asterisk* – please visit our website for instructions on these models and for additional alternate programming instructions: www.overheaddoor.com/alt-programming- UWWC.pdf
Chart A

Chamberlain® LiftMaster® CraftsMan®

| Purple Learn Button, Security +®, 2006-2014, 315 MHz| 2
Orange/Red Learn Button, Security +®, 1996-2005, 390 MHz| 3
Yellow Learn Button, Security +2.0®, 2011-current, 390 MHz| 4
Green Learn Button, Billion Code®, 1993-1995, 390 MHz| 5
Genie®| 315/390 MHz, Intellicode® II, 2010-2011| 6
Overhead Door®| 315/390 MHz, CodeDodger® II, 2010-2011| 6
Sommer®| 310 MHz, Rolling Code| 7
Linear®| 318 MHz, Mega Code®| 8
Wayne Dalton®| 372.5 MHz, Rolling Code, 1999-current| 9
Ryobi®| 372.5 MHz, Rolling Code| 10
Guardian®| 303 MHz, Fixed Learn Code| 11
Xtreme® brand| 303 MHz, Fixed Learn Code| 11
Marantec®| 315 MHz, Fixed Learn Code| 12
FAAC®| 433.92 MHz, Rolling Code| 13
*Chamberlain®| 390 MHz, 9 Switch/3 Position Dip Switch| – TEACH & PAIR –

Must have existing

operational remote.

Stanley®| 310 MHz, 10 Switch/2 position Dip Switch
Genie®| 390 MHz, 9 & 12 Switch/2 Position Dip Switch, 1993-1995| For these dip switch

instructions, visit www.overheaddoor.com*

*Overhead Door®| 390 MHz, 9 Switch/3 Position Dip Switch, 1993-1995

NOTE: During programming, the garage door opener will operate. Ensure that the garage door opening is clear of personnel or any obstructions.

 FIND SPECIFICATIONS & LEARN THE BUTTON

1.  Locate the brand and opener/receiver specifications for your device by consulting the label on the opener/receiver, the instruction manual, the current remote controls for the opener, or the original manufacturer of the opener/receiver.
2.  Find the LEARN/PROG button on your device – shape, color or name of this button could vary by brand. For garage door openers, be sure to check under the light covers. For commercial or gate openers, this button may be on the circuit board of the opener. In some cases, this button could also be on an external receiver that is mounted on or nearby the product. Consult the devices manual if needed.

PROGRAMMING THE UNIVERSAL WIRELESS WALL CONSOLE

IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button – move immediately to the proper section below. For all other ID#s, proceed to LEARN METHOD section.
IMPORTANT: Please visit www.overheaddoor.com/alt-programming-UWWC.pdf to find additional instructions and programming methods such as how to program dip switch technology, how to use the TEACH & PAIR method and how to change blink rate patterns.

LEARN METHOD (RECOMMENDED PROGRAMMING)
Review Chart A to find your specifications and available programming options. Each button can be programmed individually to operate up to 3 different brands of garage door openers and gate receivers.

1.  Remove activation tab from inside battery compartment.
2.  Find and remember the required number of button presses (ID#) in the LEARN METHOD column next to your brands/specification in Chart A. REMEMBER: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button ONLY – move immediately to instructions below. For all other ID#s, proceed to step 3.
3. Press and hold down the DELAY button @ 5 seconds until ALL 3 BLUE LEDs start blinking and then release.
4. Press the DOOR button of your choice the required number of times from Step 1 (Chart A). TIP: You may program all 3 DOOR buttons at one time if preferred. The DELAY button press will signal completion for all buttons.
5.  Press the DELAY button one time to signal the entry is complete.
6.  On the opener, press the LEARN/PROGRAM button for 2-3 seconds then release.
7.  Press the DOOR button you just programmed once every two seconds until the opener operates.
8.  When the door stops moving, press the DOOR button again to test. Programming is complete.

MOUNTING THE WALL CONSOLE

Wall Consoles should be mounted at least 5 feet from floor in a convenient location within sight of the garage door.

Mounting to garage framing:

1.  Mark and drill a 3/32” pilot hole for the slotted mount screw. See Fig-A.
2.  Install included screw into pilot hole, leaving 1/8” gap between the screw head and wall.
3.  Hook the slotted mount on back of Wall Console over the screw.
4.  Mark and drill a 3/32” pilot hole for the screw under battery door.
5.  Secure Wall Console to the wall. (Do not over-tighten).
6.  Reinstall batteries and battery cover.

Mounting to drywall:

1.  Drill 3/16” pilot hole for slotted mount drywall anchor. See Fig-A.
2.  Lightly tap drywall anchor into hole with a hammer until flush with wall.
3.  Install included screw into anchor, leaving 1/8” gap between the screw head and wall.
4.  Hook the slotted mount on back of Wall Console over the screw.
5.  Mark position of pilot hole for the drywall anchor under the battery door and remove wall concle
6.  Drill a 3/16” pilot hole for the drywall anchor under the battery door.
7.  Lightly tap anchor into hole with a hammer until flush with wall.
8.  Secure Wall Console to the wall. (Do not over-tighten).
9. . Reinstall batteries and battery cover.

OPERATING THE WALL CONSOLE

Operating a Door:  Press and release the door button of your choice. The door will move up or down.

To initiate the DELAY feature on any DOOR button:

1.  Press and release the DELAY button one time for 10 seconds, two times for 15 seconds, or three times for a 20 second DELAY.
2.  Press and release the DOOR button of your choice. Activation will be delayed by 10, 15 or 20 seconds.

Clearing out the wireless wall console:

1.  Press and hold down both the top DOOR button and the bottom DOOR button at the same time.
2.  When LED on the middle DOOR button gives two long blinks and goes out – then release both buttons (@ 5 seconds).

References

• Overhead Door™ Brand Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>