WOLFVISION 102347 Remote Pack for VZ-8neo

Check out our internet homepage for additional information
www.wolfvision.com/support

Precautions

Please observe the following:

• Use this Visualizer only with the correct voltage as shown on the type label !
• Do not expose the Visualizer to heat or moisture !
• Protect the Visualizer from excessive shocks !
• Make sure that sufficient air circulation for cooling the Visualizer is possible!
• If there is any abnormality (abnormal noise, smell, smoke etc.) disconnect the Visualizer from mains immediately and contact your Visualizer dealer!
• Do not use a damaged power supply/power cord. This may cause short circuits or electrical shocks!
• To prevent danger, do not modify the Visualizer or operate without the cover panel firmly in place!
• Do not expose the Visualizer to water, metallic objects or any flammable material.
• Avoid installing the Visualizer in locations exposed to strong magnetic fields or electrical currents.
• Avoid installing the Visualizer in environments where there is radiation. This could cause monitor image distortion or damage to the camera sensor.
• Do not pull the plug from the power socket with wet hands!
• If the Visualizer is not used for a long time, disconnect it from mains!
• The supplied HDMI cable is designed for demo purposes only. Use high-quality cable for final installation.
• Use the included 12Vdc power supply. Alternatively, a PoE+ injector can be used (the PoE+ injector has to be certified to IEC/EN/UUCSA 60950-1 or 62368-1 and has to meet the industry standard IEEE802.3at-2009).

Precautions for LED light according EN62471:

• LED lighting system – Do not stare into beam!
• Do not modify the LED lighting system!
• Do not view the light beam with optical instruments!
• Ne pas regarder dans l’objectif lorsque le visualiseur est en marche!

Information to the user and integrator
This product is designed, inspected and built according to local directives and standards, e.g. EMC, ANSI/UL Standard 62368-1 and CAN/CSA Standard C22.2 No. 62368-1 and CB-Scheme.
For further details please contact your dealer orWolNision (www.wolfvision.com).
The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment!

Worldwide Patents

• us 7,035,011
• KR 0576806
• RU 2265284
• TW 1226969
• EU 0 362 737
• DE P58907684.1-08
• CN 89107780.4
• JP 1725033
• KR 128059
• us 5,027,219
• EU 0 987 874
• JP 3 544 900
• AU 765617
• CN ZL99118847.0
  and others

Copyright Information
Copyright© by WolNision. All rights reserved.
WolNision, Wofu Vision and ‘lJ:. mi t,lll. -if\ are registered trademarks ofWolNision HoldingAG, Austria.
No part of this document may be copied, reproduced, or transmitted by any means, without prior written permission from WolNision. Except documentation kept by the purchaser for backup purposes.
In the interest of continuing product improvement, WolNision reserves the right to change product specifications without notice.
Information in this document may change without notice. Disclaimer: WolNision shall not be liable for technical or editorial errors or omissions.

The units are “MADE IN EU/AUSTRIA”
Printed in Austria, January 2017

Introduction

The Visualizer offers the possibility to upgrade using an optional Feature Pack which adds additional functionality. This upgrade is activated by loading a valid Feature Pack code.
Currently available add-on features are:

• Infrared remote control (additional hardware included)
• Picture in Picture Mode for Live to Freeze comparison
• internal Memory (9 images)
• USB Host port, for memory extension via USB stick
• User-defined settings can be stored on USB stick (depending on model)
• Fading effects, for seamless cross-fading between different image sources

Additional features may be added in the future with later firmware versions.

Where you can get the Code to activate the Feature Pack

The Feature Pack code is a unique number and it depends on the serial number of the Visualizer.
The code can be supplied by your dealer (together with the Visualizer or separately).
Any questions regarding Feature Pack code availability, please contact either your dealer or WolNision directly (contact details on the last page of this manual).

Important note:
The Feature Pack is not pre-installed and user activation is required!
Enable the Feature pack by using one of the two following methods:

1. Connect a pre-prepared USB stick to the Visualizer and follow the on-screen instructions  OR
2. Use vSolution Link Software by WolNision, selecting the Administration tab, and then clicking on Online/Offline Activation.

Using the prepared USB-Stick

• Connect a power source and a monitor to the Visualizer then switch on the Visualizer
• Plug in the USB stick.
• A pop-up message will ask if you want to enable the features.
• Use the navigation keys on the camera head to confirm the line “YES”.

Please note that you will not be able to use the remote control until the additional features have been activated.

Using vSolution Link Software by WolfVision

• Install the software vSolution Link onto your computer-be sure to install administration functionality.
• Connect a power source and your PC via USB or LAN to the Visualizer and start the software.
• Select the ribbon “Administration” and click on either Online or Offline activation:
  • Online activation requires an internet connection for the software
  • Offline activation requires the activation file or at least the activation code

For more details please consult the help section of the vSolution Link Software by WolNision. Please note that older versions of the software may not support Feature Pack activation. Latest version can be downloaded from:
www.wolfvision.comlsupport

Components of the Visualizer

1. Connectors (on the back of the unit, as shown below)
2. IR-receiver camera head
3. Camera keys for camera control and menu navigation (see page 9) #4 IR-remote control (see pages 5 and 6)

Connectors (#1)

5 USB port to Client (to peripheral devices, for external storage units) (see

page 9)

Infrared Remote Control (#4)

Infrared Remote Control
Please note that an infrared remote control can only be used up to a certain distance from the unit. Objects situated between the Visualizer and the infrared remote control, and weak batteries, interfere with reception.

If the Visualizer can only be controlled from a close distance, or if it cannot be controlled at all with the infrared remote control, you may have to change the batteries.
Open the cover on the back of the remote control and replace the two 1.5V AAA (Code LR03) batteries with new ones.
Check Recycle the the polarity batteries! of the batteries!

Different IR Codes
If you want to work with more than one Visualizer in the same room, the units should be set to different infrared codes, in order to control them all individually.
The IR code of the Visualizer has to match the code of the remote control.
To change the IR code, enter the on-screen menu, go to “Advanced Settings/ Miscellaneous Settings” and set the “IR Code” to A, B, C or D (code A is default). To change the IR code on the remote control, simultaneously press PRESET 1, PRESET 2 (#10) and ZOOM TELE (#15). Each time this key combination is used, the code switches from A to B, C, D … A .. .in the given order.
For resetting the remote control to code A, simultaneously press PRESET 1, PRESET 2 and ZOOM WIDE.

Keys on the IR-Remote Control

6  MENUkey

Pressing MENU key activates the on-screen menu (see page 9).

7 HELP/RESET key for on-screen menu (double function of MEMORY key No. 7)

While you are in the on-screen menu you can activate the on-screen help by pressing the HELP key. Pressing this key for 2 seconds resets the selected menu item (see page 9).

8 MENU NAVIGATION keys (double function of MEMORY keys No. 2. 4. 6 and 8)

For navigating through the on-screen menu (see page 9).

9 PiPkey

For activating the Picture in Picture mode for Live to Freeze comparison (see page 7).

10 PRESET keys (programmable settings)

For storing a preset, press one of the PRESET keys for more than 2 seconds. For recalling a preset, press the PRESET key quickly.

11 MEMkey

For displaying pictures of the internal memory (see page 7).

12 VZkey

For displaying the live image of the camera (see pages 7 and 8).

13 AUTO FOCUS (AF) key

Pressing this key activates the Auto Focus.

14 Manual FOCUS keys

For focusing the picture.

15 ZOOM keys

To enlarge or downsize the pick-up area of the camera.

16 USBkey

For displaying pictures of the USB memory (see page 8).

17 EXTkey

Shows the signal of the external input, use the VZ key to display the live image again (see pages 7 and 8).

18 SNAPSHOT key

Pressing this key activates the SNAPSHOT function (see page 7).

19 FREEZE key

Freezes the current image.

20 MEMORYkeys1-9

For saving and recalling pictures of the internal memory (see page 7).

21 ENTER key (double function of MEMORY key No. 5)

To enter selected submenus when on-screen menu is activated (like MEMORY key No. 6) (see page 9).

22 Manual EXPOSURE keys (brightness adjustment)

When the EXPOSURE keys are pressed, the Visualizer changes the image brightness .
For specialists: The behaviour of exposure can be changed in the on-screen menu (see page 9).

23 POWER key

Pressing this key switches the unit on and off.
When switching on the unit, the Visualizer runs the power-on preset.

Live to Freeze Comparison / Picture in Picture (PiP)
The Picture in Picture Mode offers the possibility to show two different pictures at the same time on one screen. Just press the PiP key (#9) to activate the Picture in Picture mode. The current picture (external signal, image memory, camera image) will be shown frozen in the lower left corner and the live image will be shown full sized. The content of the live image can be changed i.e. by recalling a stored image memory. Additionally the behaviour of the PiP mode can be changed in the on-screen menu to show the pictures Side by Side (Side by Side is not available when camera aspect ratio is set to 4:3 in the on-screen menu).

Internal Image Memory

You can store 9 images in the internal memory and recall them by simply pressing the respective numerical key on the remote control quickly.
Storing an image: Press the desired MEMORY key (#20) for at least 2 seconds
Recalling an image: Press the respective MEMORY key (#20) quickly
The internal memory can be erased or filled automatically in the on-screen menu of the MEM mode.

Snapshot
Built-in Memory (external storage device not connected)
By pressing the SNAPSHOT key (#18) the current image is stored in the next free memory. When all 9 memory locations are full, the oldest will be over written (circular buffer).
External storage device connected
By pressing the SNAPSHOT key (#18) the current image is be stored on the USB device and a message appears on the screen. The stored images are in JPG format and can be edited/viewed on a computer.
All pictures are stored with date and time stamp.
The properties of the USB functions can be changed in the on-screen menu (Advanced Settings – USB Stick Settings), like default picture folder (document directory) and the file names (“WV” and consecutively numbered).

MEM Mode
To start the MEM mode, press the MEM key (#11). A split image with the stored pictures will be displayed. Additionally a status line with picture information is shown on the bottom of the screen. Pressing the VZ key (#12) returns to the camera live image temporarily. The presentation will stay at the last shown picture, to continue use the MEM key.
To select one of the currently displayed pictures move the picture bar with the NAVIGATION keys and confirm it with the ENTER key. Use MEMORY keys 4/6 to show the previous/next picture. Use the ENTER key (#21) to return to the split view.

Use the MENU key for storage organization like deleting pictures and filling the all 9 memories automatically in a defined time interval.

USB Mode
To start the USS mode, press the USS key (#16). A split image with the available folders and stored pictures will be displayed. Additionally, a status line with picture information is shown on the bottom of the screen. Pressing the VZ key (#12) returns to the camera live image temporarily. The presentation will stay at the last shown picture, to continue use the USS key.
To select one of the currently displayed pictures move the picture bar with the NAVIGATION keys and confirm it with the ENTER key. Use MEMORY keys 4/6 to show the previous/next picture. Use the ENTER key (#21) to return to the split view.

Use your computer for organization of the USS storage device like creating or deleting folders, moving pictures from one folder to another, deleting pictures or formatting of the USS storage device.
Please note formatting the USB storage device will delete all data.
Supported file systems are FAT16 and FAT32. Supported picture file format is JPG format.

Saving Visualizer Settings onto a USB-Stick
The Visualizer offers the opportunity to save menu settings and preset settings onto an USS stick (USS storage device) as an XML file.
Change the settings to the desired values and store it on the USS stick (in the on-screen menu, Advanced Settings / USS Stick Settings).
When you connect the USS stick with the prepared XML file, a respective on- screen message will pop-up for information.
As soon as the USS-stick is removed, the previous settings are restored.
The file will be stored in the default USB folder which can be changed in the on-screen menu (,, WOLFVISION” by default).
All settings of the Visualizer can be changed in the on-screen menu (see next page).

Built-in Digital Scaler (for Extern-in and USB-Stick)
The Visualizer has a built-in digital image scaler which can process the signal from the external input and output it in the same mode as the Visualizer image (For example: If the Visualizer is set to output an 1080p (FullHD) image to the projector and the computer outputs an XGA signal, the scaler of the Visualizer converts the XGA image of the computer to 1080p. As a result the projector does not readjust the input mode when switching between the Visualizer and computer image).
In addition images on a connected USS-stick are automatically scaled to the current output mode of the Visualizer.
The output resolution of the Visualizer can be changed in the on-screen menu.

Integrated Seamless Switch
The Visualizer has an integrated Seamless Switch.
This allows for a seamless transition (fade-over/dissolve effect) when switching between the Visualizer image, the image from the external input, the internal image memory of the Visualizer and images on an USS-stick. This feature makes switching from one media to the other appear very smooth and professional. The behavior of the Visualizer can be changed in the on-screen menu (see next page).

CODES – Short Keys with the remote control

• Storing presets:
• Keep the desired PRESET key (#1 OJ pressed for 2 seconds.
• Recalling presets:
• Press the desired PRESET key (#1 OJ quickly.
• Storing images:
• Keep the desired MEMORY key (#20) pressed for 2 seconds.
• Recalling images:
• Press the desired MEMORY key (#20) quickly.
• Activating the on-screen menu:
• Press the MENU key (#6) to activate the on-screen menu. Use the Number keys (#8) to navigate and Numbers key (#21)toselect. For the help function, press the HELP key (#7).
• Resetting single items of the on-screen menu:
• Select the desired item in the on-screen menu and keep the Number 7 key (#7) on the remote control pressed for 2 seconds.

Change IR code:
Change the IR code in the on-screen menu “Advanced Settings/ Miscellaneous Settings” and set the “IR Code” to A, B, C or D (code A is default). To change the IR code on the remote control, simultaneously press both PRESET 1+2 keys (#10) and the ZOOM TELE key (#15). Each time this key combination is used, the code switches from A to B, C, D … A … in the order given.
For resetting the remote control to code A, simultaneously press PRESET 1, PRESET 2 and ZOOM WIDE.
The LED on the remote control shows the selected code (it flashes one time for code A, two times for code B, three times for code C and four times for code D).

Where you can check the state of Feature Packs On-Screen Menu
For regular use of the WolNision Visualizer, it is not necessary to go into the Visualizer’s menu and change settings. Inexperienced users should not make any adjustments here.
To enter the on-screen menu press the MENU key (#21 on the remote control or use the key on the camera head and keep it pressed until the menu appears). Settings of the Visualizer’s basic functions and the built­in camera can be made here using the 4 SELECT keys on the remote control (=the numerical keys with arrows#B) or navigation keys on the camera head.
If more information on a function in the on-screen menu is required, set the cursor in the respective line and press the HELP/? key (#7). A detailed description of this function appears on the screen.
The functions of the on-screen menu are not described in detail in this user manual as the help function is an integrated part of the Visualizer’s software (firmware). The information you see on your screen always belongs to the current Visualizer firmware.

Advanced Settings
USB Settings
To store Visualizer settings on a USB stick and to change the basic settings of the USB port.
Device Info
In this sub-menu, you can check the version number of the currently installed firmware and the state of the enabled Feature Pack functions.

CONTACTS
Manufacturer/ Worldwide Distribution

WolfVision GmbH
A-6833 Klaus    Tel: +43(5523)-52250, Fax: +43(5523)-52249
AUSTRIA        E-Mail: wolfvision@wolfvision.com

International Distribution Offices
USA
WolfVision Inc.
Duluth (Atlanta)  E-Mail: sales@wolfvision.us / support@wolfvision.us
Asia
WolfVision Pte Ltd Singapor                            E-mail: wolfvision.asia@wolfvision.net 

Middle East
WolfVision Middle East
Dubai              E-Mail: wolfvision.mideast@wolfvision.com

Germany WolfVision Germany  E-mail: wolfvision.deutschland@wolfvision.com

Nordic
WolfVision Nordic Oslo  E-mail: wolfvision.nordic@wolfvision.com

Japan
WolfVision Co. Ltd. Tokyo  E-mail: wolfvision.japan@wolfvision.com

United Kingdom WolfVision UK Ltd. Marlow  E-Mail: wolfvision.uk@wolfvision.com

Internet Homepage: www.wolfvision.com
E-Mail to technical support: support@wolfvision.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>