Vybra VS001-W Multi 3 In 1 Heater Cooling Fan and Air Steriliser User Manual

VS001-W Multi 3 In 1 Heater Cooling Fan and Air Steriliser
User Manual VS001-W (White)
VS001-B (Black)
Please read and keep it before using the product.
Made in China
5 Kingsway Andover UK Vybra

Important Safety Information

WARNING
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following:

1. This product is only suitable for indoor use and should not be used outdoors;

2. Non-professional personnel or unauthorized repair personnel may not repair or modify the machine by themselves;

3. Before plugging in the power supply, please check if the rated voltage matches the voltage in your home;

4. Keep at least 1.5 meters away from the fire source or tinder, and avoid direct sunlight;

5. It is forbidden to be used near objects that are flammable, explosive, or subject to heat, deformation, discoloration, or deterioration. It is forbidden to use in places with severe dust;

6. It is forbidden to replace the power switch by the method of  plugging (unplugging) the power cord plug;

7. To avoid overheating, it is forbidden to cover the heater;

8. It is strictly forbidden to insert any wire or other foreign matter into any hole in the machine to avoid electric shock;

9. Do not use the heater against the power outlet or under the power outlet; The power outlet should be placed behind the fan when the heater is in use.

10. Do not share the socket with other high-power appliances.

11. Do not use this heater around the bathtub, spray head, or swimming pool；

12. This product must be equipped with a Ce-UKCA-approved socket that is consistent with the rated working current.
    Do not use a mobile multi-purpose socket.

13. Fire risk when the heater is covered or incorrectly placed. Do not use a programmer or timer that can automatically connect the power supply.

14. If the heater fails, please turn off the power and unplug the power cord immediately.

15. Before use, check the power cord and the plug. If the power cord is damaged, in order to avoid danger, the user must not disassemble or replace the power cord. It must be replaced by the manufacturer’s maintenance department or a similar professional.

16. Children, elderly people, or patients who have lost their fixed ability to take care of themselves should use this appliance under the supervision of an adult to prevent accidents;

Product Description

This product uses PTC heating, send heat by hot air, which can quickly increase room temperature. On open flame, safe, efficient, and energy-saving.

Basic Parameters
Model No: VS001-W (White) VS001-B (Black)
Rated Voltage: 220-240V~
Rated Frequency: 50-60Hz
Output Power: 2000W(H)/30W(B)
Oscillating Angle: 0°
Timer: 1- 8h

Remote Introduction

1. Cool Mode
2. Oscillating
3. Air volume
4. Air reduction
5. Warm Mode
6. Strong Wind
7. Timing
8. Sleep Wind
9. Add Temperature
10. UV sterilization
11. Reduce temperature

Note: The main buzzer will make a “beep” sound when operating the remote

| The device can be switched on and off by pressing The “ON & OFF” button
---|---
| Press the Sleep mode button on the remote control.
The display shows that the wind speed becomes minimum.
Press again to exit the sleep mode.
You can also exit the current mode by pressing the Wind Strength + button.
| Press the Turbo mode button on the remote control.
The display shows H and the wind speed becomes the max
Press again to exit the turbo mode.
You can also exit the current mode by pressing the Wind Strength + button.
| Press the Oscillation button to turn on the oscillation function.
This fan can swing left and right 80. Press this button again to stop oscillating.
| Press this key to turn on the UV germicidal lamp, the display shows U.
The UV lamp will be turned off after running for 1 hour.
Press again to turn off the UV germicidal lamp.
| In cooling mode, the LED lamp is blue.
Press this button to activate the cooling mode.
Note: The default start mode is the cooling mode.
| Press the “+” button on the left side of the remote control to increase the volume of air, and press the “-” button on the left side of the remote control to decrease the airflow. The cool mode can be used for 9-level settings, warm mode can be set for 4 levels.
**| The displayed number in heat mode is red.
Press this button to activate the heat mode.
Note: In heat mode, there is no strong mode or sleep mode.
| In heat mode, press the temperature button on the right side of the remote control to set the temperature(1-30℃).
Note:** this button does not work in cool mode.
| Press the timer button on the remote control to set 1 t ours of timing.

Remote Operation Introduction

The remote control should be pointed at the remote control signal receiver on the display to maximize the remote control signal.
Effective distance: 5M

Warning:
A phenomenon that occurs due to the overlap of the frequencies of the remote control, in order to avoid misuse, please operate remotely:

1. This bladeless heater may react when using a remote device for other appliances.
2. When using the remote control of this bladeless heater, other electrical appliances may react.

The switch on the remote will turn this fan to standby, not complete shutdown. Use the switch on the main unit to completely power off when this fan is not in use.
If this fan is not in use for a long time, please unplug the power cord.

Heating Mode Instructions

Press the warm mode button and the display shows the ambient temperature.
Press the temperature button to set the temperature, and the display will flash digitally, which can be set to 1-30 °C.
The set temperature should be higher than the ambient temperature so that the heating function will be turned on;
When the ambient temperature reaches the set temperature, the heating function will stop and turn into a cool breeze;
The ambient temperature is lower than the set temperature and the heating function will automatically activate.

Set temperature > ambient temperature: heating function on.
Set temperature ≤ ambient temperature: heating function stops
Note: The default setting temperature is 25 °C. In the warm mode, when the ambient temperature is below 0 °C, the display only shows 01 and does not display a negative temperature value. If the warm air mode runs for over 9 hours, the machine will automatically stop running. Restart by pressing the host power button or by using the remote control.
Warm mode: use the remote to set the temperature, the host does not support this operation.

Host

Insert the plug into the socket, turn on the power switch, and the machine enters the standby state:
Click the power button of the host, the buzzer will prompt you to click, and the fan will start running. Press and hold the power button for 2 seconds, the buzzer will prompt you twice, and then stop running after you release the hand.
Air Volume Shift
When the host is in operation: click the main power button to switch the air volume from 1 to 9.
Oscillating operation
Press and hold the power button for 1 second, the buzzer will beep once, and the fan start oscillating.
Press and hold the power button for 1 second again, the buzzer will beep once and the fan stop oscillating.

Installation location and precautions

Location
Please place the fan in a horizontal position. If there is a slope, should be on a soft surface to avoid the fan falling over; please do not use it in high temperatures and humidity (bathroom, kitchen).

Safety System: this heater fan includes an overheat protection sensor and an automatic fail-safe that cuts power to the unit if it’s accidentally tipped over or overheats. If this sensor is triggered, unplug the machine and allow the fan cool. Check and remove any obstructions before restarting the heater fan and be sure to place them on a hard, level surface.

The battery installation method and troubleshooting analysis

Battery installation method

1. Open the remote control battery cover;
2. Load two new AAA (No. 7) dry batteries;
3. Close the battery cover of the remote control.

Please insert the battery correctly

Machine Malfunction analysis

into the socket?
The Remote does not work| The battery is dead?
Is the battery installed correctly?
Is the remote control aligned with the signal receiver?
If the above method can’t solve the malfunction, please connect with customer service, do not disassemble, repair, and install it yourself.

Maintenance and maintenance

Unplug the power supply before performing maintenance.
Please do not put the fan in the water or splash it, which may cause the machine to be damaged.
Do not use banana oil, benzene, alcohol, bleach, or metal objects to wipe the surface of the fan, which may cause discoloration of the surface.

Surface cleaning
Wipe the surface with a soft, dry cloth;
If especially dirty, dilute with a mild detergent and wipe with a soft cloth. Then wipe with a dry soft cloth.

Air inlet/outlet
Use a soft brush or a vacuum cleaner to clean the dust at the air inlet and outlet. Please clean it when there is less dust. Too much dust is not healthy and will reduce fan efficiency.
Remote control
Gently wipe the surface of the remote with a soft, dry cloth.
If you don’t use it for a long time, avoid battery consumption.
Please remove the battery inside the remote control.
Storage
Not used for a long time can be placed in a plastic bag after cleaning;
Please avoid vibration places (car trunk.) and electrical appliances with cooling/heating functions;
Please avoid placing it in direct sunlight, high temperature, and humidity; Please keep it out of reach of young children.

Connect with APP

1. The phone connects to WIFI
2. Please download APP “TUYA smart” or “SMART life” or scan the QR code below to download APP
   |
   ---|---
   http://smart.tuya.com/download| https://smartapp.tuya.com/smartlife
3. When using the App first time. you need to register an account.
4. Press and hold the LED display for 5 seconds ( beep 3 times) when “F” appears and blinks .press “Confirm indicator rapidly blink” to continue. select your WIFI network and input your password. press”confirm” to continue.
5. Login APP and click”+” or”add device” in the upper right corner. Click “all devices” on the right side and choose the fan
6. The App will automatically match the device. after a match is found. you will be prompted and you can rename your device. Press”done” to finish.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>