Vybra VS001H Halo Bladeless Smart Fan and Air Purifier Instruction Manual

Vybra VS001H Halo Bladeless Smart Fan and Air Purifier

IMPORTANT SAFEGUARDS

Please read all instructions before using this product and keep these safety instructions for future reference.

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following:

1. This product is only suitable for indoor use and should not be used outdoors;
2. Do not use the Halo on a wet surface, but set up on a dry, horizontal platform away from heat sources, corrosive air and moisture;
3. Do not place any objects on the Halo and do not cover the air inlet or outlet;
4. Ensure the ventilation openings are free of dust, lint, hair or any other obstacles that could impair the flow in/out;
5. The Halo should be kept a distance of 30 cm around to ensure good air circulation;
6. Keep at least 1.5 meters away from fire source and avoid direct sunlight;
7. Non-professional personnel or unauthorised repair personnel may not repair or modify the machine by themselves;
8. Before plugging in the power supply, please check the rated voltage matches the voltage in your home;
9. Do not move the fan when it is connected to the power supply;
10. Do not pull in/out the plug by pulling or dragging the cable, do not grip the cable
11. Do not insert any wire or other foreign matter into any hole of the machine;
12. Do not share the socket with other high-power appliances;
13. Do not use the Halo in the bathroom, or near water;
14. Do not immerse the fan power cord, or plug in water or other liquid;
15. The use of an extension cord is not recommended unless it is used for testing by electrical maintenance professionals;
16. Do not run the cable under carpets and do not cover it with carpets or similar covers;
17. Route the cable away from the walking area to avoid tripping over;
18. Turn off the Halo before unplugging;
19. Ensure the Halo is switched off and unplugged before cleaning, moving or servicing;
20. Unplug the Halo if you are not going to use the unit for a period of time
21. This product must be equipped with a UKCA-approved / CE-EU – fixed socket that is consistent with the rated working current;
22. If the Halo fails, please turn off the power and unplug the power cord immediately;
23. Before use, check the power cord and the plug. If the power cord is damaged, please do not switch on, but contact the seller;
24. For safety reasons, competent persons only should use this appliance.

PRODUCT SPECIFICATIONS

8.9 kg

WHAT’S INCLUDED

1. Main body of the fan

2. Fan air-outlet ring

3. The fan air filter

4. Pillar x 2
   

5. Power supply Pillar x 1

6. The power adapter

7. Wrench x 1

8. Screw x 1

9. The remote control

10. The user manual

FAN ASSEMBLY

Remove all packaging materials
STEP 1: Install the strut

1. First put the motor on the foam as shown in the figure;
   

2. The power supply pole is installed to the specified hole 2 position, press the push button of the pole, insert the motor hole position; The shrapnel button springs up in the hole and is fixed;
   

3. Install the other two poles 1 – 3 in the same way.
   

STEP 2: Install Wind Rings

1. Stand the fan on a stable, dry surface 4;
   

2. Install the wind ring to the motor 5;
   

3. Insert the wind ring screw into the hole at the bottom of the wind ring and tighten the wind ring screw clockwise with the special wrench (6).
   

INSTALLING THE FILTER

This product is equipped with a clean air HEPA filter.
Before the fan is used, the filter should be fitted so the purifying function can work. This product has memory function.
After 720 hours of operation, the screen replacement indicator light will come on.
After replacing the air filter, press the On/Standby button of the remote control for 5 seconds to extinguish the prompt and the running time will reset.

Installing the air filter

1. Rotate the air filter cover counter-clockwise to remove the air filter cover;
2. Put the air filter into the fan main body;
3. The filter cover is then loaded into the fan main body and fixed by clockwise rotation.

OPERATING INSTRUCTIONS

Installation position

• Place the fan on a flat, horizontal floor / surface;
• Do no obstruct the air inlet;
• Keep away from curtains when using the fan to avoid any accidents;
• Do not place objects within 30 cm in front of the air outlet.

Up & down tilt air supply

• Gently press forward / backward on the top part of the far air-outlet ring;
• The ring can be adjusted to supply the output air upward or downward.

Connect the power supply

• Connect the power cable to the power port on the base of the fan 1;
• Plug in the adapter to the mains 2;
• When the fan beeps, it is connected.

TOUCH SCREEN CONTROL PANEL DISPLAY ICONS

TOUCH SCREEN CONTROL INSTRUCTIONS

| Press to start and stop the fan and to enter standby mode.
Hold for 5 seconds for WiFi mode
Modes| | Press to switch the between modes:
Automatic air-speed, strong air-speed, sleep mode, natural mode.
Automatic mode : displays ‘A’ automatically adjust the air speed according to the real-time detected PM2.5 content.
Strong Mode : the highest fan speed
Sleep Mode : the lowest fan speed
Natural Mode : variable from 3-4-5 speeds Press the fan speed key to exit the mode
Timer| | Press to set the 1 – 8 hour timer.
When the Halo is switched off, the previous setting with be cancelled.
Movement| | Press to switch the swing – left and right – angle in turn: 30º, 60º, 90º, 120º and cancel
Fan Speed| | Press to change the fan speed from 1 – 9
Press and hold for 2 seconds to enter the ‘strong’ mode

REMOTE CONTROL FUNCTIONS

| Press or Power ON or standby Press for 5 seconds to recalculate the filter timer
---|---
| Press to switch the fan ON and switch between modes – automatic, strong, sleep and natural
| Press to switch the swing ON/OF. Default 90º
| Press to switch the swing – left & right – angle: 30º, 60º, 90º, 120º
|  Press to set the 1 – 8 hour timer-off (standby mode). When the power is turned off, the previous setting will be cancelled
| Press to turn UV lamps ON/OFF They will turn off automatically after running for 1 hour
| Press to turn the plasma ON/OFF
| Press to turn tone sound ON/OFF
| Press to turn the display screen light ON/OFF
| Press to turn on the ambient light ON/OFF and click to adjust the brightness. 1 – 4 speed
| Press to adjust the fan speed 1 – 9

REMOTE CONTROL OPERATION GUIDE

NOTE: When using the remote control, please point the remote control at the direction of the fan display screen, as show in Figure 1.

NOTE: Remove the insulating film before using the Halo for the first time, as shown in Figure 2.

Replacing the battery

1. press from the side of the bottom of the remote control to release the battery holder Figure 1;
   

2. Pull down and remove the battery holder Figure 2;
   

3. When loading the battery, please press the “+” pole face upwards Figure 3;
   

4. Install the battery holder back into the remote control figure 4.
   

IMPORTANT INFORMATION

• Please do not charge the battery;
• Keep out of reach of children and do not swallow the battery;
• If the remote control button does not work, please try a new battery;
• When loading the battery, check it is the correct way round;
• Operation may be interrupted by other electrical appliances, please use the remote control away from other electrical appliances;
• When not in use for a long period of time, please remove the battery.

CLEANING

• CAUTION: To prevent damage to the appliance do not use alkaline cleaning agents when cleaning, use a soft cloth and a mild detergent;
• Regular cleaning of your product will keep it in safe and proper working order.

BEFORE CLEANING

• When not in use or before cleaning, always disconnect the Halo from the mains supply;
• Never immerse the Halo in water or any other fluid, do not rinse under a tap;
• Use only a moist cloth to clean the Halo.

CARE AND CLEANING

• The Halo should be cleaned with a mild soap (detergent) and a damp cloth or sponge. Ensure that all traces of soap film are removed with a damp cloth or sponge after cleaning;
• Do not use spray cleaners;
• A vacuum cleaner can be used to lightly vacuum dust from the vents.

HALO ACCESSORIES

REPLACEMENT FILTER

SKU| VSHHF
EAN| 5060663690371
ETSI EN 303 645 compliant

TROUBLESHOOTING

• The power cord is not connected
• There is no power from the socket
• The power switch is not on
• The machine is damaged
• Check the fuse

|

• Connect the power cord
• Check the socket is turned on
• Turn the Halo on
• Contact Vybra Solutions: sales@vybrasolutions.co.uk

Remote Control issues|

• The battery is depleted or discharged
• The battery is incorrectly installed
• The remote control is not properly aligned with the signal receiver

|

• Replace the battery
• Reinstall the battery correctly
• Point the remote directly at the display
• Move closer to the Halo

PRODUCT SPECIFICATION

Technical Information

HEPA, PLASMA, UV Information

| Common Use
---|---
HEPA| Airborne particles of 0.3 microns
PM2.5 (fine particulate matter smaller than 2.5 microns)
Aerosols 0.3 – 10 microns
Allergens – dust mites, pollen, mould, etc.
PLASMA| In a limited range, it can kill staphylococcus and Escherichia coli in the air
UV LAMPS| To kill or weaken airborne infectious particles within limited limits, eg bacterial, mould, etc

How to Connect the VYBRA HALO to the App

1. Connect your mobile phone to the same WIFI environment with the Halo;

2. Search “Tuya Smart” or “Smart life” in the APP Store or scan the QR code as below to download and install the APP:
   TUYA smart
   
   SMART life
   

3. Open the APP, register an account and login;

4. In the Halo stand-by state, long-press the fan control screen ON/STANDBY key for 5 seconds, until the WIFI icon starts blinking to enter the network pairing mode;

5. On the App Page, click “+” → “Small appliance” → “Fan” at the upper right corner of the APP page to enter the page of adding devices;

6. Check and confirm that the WIFI icon on the fan screen blinks quickly, then click “Confirm that the indicator is blinking quickly” → enter the model connection password (WIFI password) to connect;

7. Check and Confirm that the WIFI icon on the fan screen blinks slowly.

8. On the App Page click “Compatibility Mode” → “Confirm that the indicator blinks slowly” → enter the model connection password (WIFI password) to switch the device hotspot for connection as prompted;

9. The APP displays that it has successfully connected with the Fan.
   Note: The fan WIFI icon blinks fast/slow, is switched by a long-press on the fan screen on/ Stand-by button for 5 seconds.

Scan the QR code to download Vybra HALO User Manual

A guide to 2.4GHz and 5GHz networks
If you own a “dual band” router (identified on the sticker on the back), you will have the option of using two bands throughout your home: 2.4GHz and 5GHz.
What’s the difference between 2.4GHz and 5GHz?
Each WiFi enabled device in your home can connect to one of the 2.4GHz or 5GHz bands at one time. The 2.4GHz network is slightly slower, but can cover a large area, as the signal is more effective at penetrating thick walls. The 5GHz network is faster but has a shorter range, offering a better connection for devices within close proximity. It’s worth noting some connected devices, such as older smart phones, are not compatible with 5GHz networks.
How do I find out which band I’m using by default?
Most dual band routers will be set up with two separate WiFi networks by default. Often the 5GHz network will often have “5G” or “AC” at the end of its name. If this isn’t the case, either the router may be selecting the band automatically, or the router or device may not support 5GHz. (Note: 5GHz WiFi is not to be confused with 5G wireless mobile networks).
Some routers will automatically do a quick scan to determine which channels have the least interference and choose the best option for your device. In other cases, your device will connect to its preferred network, which could be the one you most recently connected to, or the one you have manually selected the most often.
To see which band you’re connected to, open the WiFi preferences on your device. Whether you’re using a phone, tablet, computer, TV or another connected device, you should be able to see two WiFi network options in the settings. From there you can select which one you’d prefer to use.
Adjusting the settings on a router
Every router has an IP address (e.g. 192.168.1.1) displayed somewhere on the device. Type that into a web browser while you’re connected to your WiFi network. You’ll reach a login page – use the default login details (written near the IP address on the device) to proceed. Once logged in you’ll see a configuration page where you can edit network preferences, as needed.

Switching between 2.4GHz and 5GHz

Windows

• Click on the WiFi icon in the bottom right corner of the task bar.
• Then click on the network you want to use from the list of available networks.
• Click Connect (type in the password and click Next if it’s your first time connecting to this network).
  

Apple Mac

• Click on the WiFi icon in the top menu bar
• Then select the network you want to use from list of available networks.
• If applicable: type in the password when prompted and click Join.
  

Apple IOS

• iOS devices: tap Settings > WiFi
• Select the network from the list of available networks
• Type in the password > Join
  

Apple IOS

• iOS devices: tap Settings > WiFi
• Select the network from the list of available networks
• Type in the password > Join
  

Android

• Settings > Connections > WiFi
• Select the network from the list of available networks
• Type in the password > Connect
  

CUSTOMER SUPPORT

vybrasolutions.co.uk | sales@vybrasolutions.co.uk

References

• Vybra for clean air & comfortable living

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>