FISHER PAYKEL CG301D Gas On Glass Cooktop Installation Guide

: June 5, 2024
: Fisher & Paykel

FISHER PAYKEL CG301D Gas On Glass Cooktop

SAFETY AND WARNINGS

⚠ WARNING!

| Electrical shock hazard
Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it.
Connection to a good earth wiring system is essential and mandatory. Alterations to the domestic wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.

⚠ WARNING!

| Cut Hazard
Take care – panel edges are sharp. Failure to use caution could result in injury or cuts.

IMPORTANT SAFETY INSTRUCTIONS

Particular attention shall be given to the relevant requirements regarding ventilation.
Read these instructions carefully before installing this product.
Please make this information available to the person installing the appliance as it could reduce your installation costs.
This appliance is to be installed and serviced only by an authorised person.
Installation must comply with your local building and local gas authority codes and electricity regulations.
Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury or damage and could invalidate any warranty or liability claims.
Appliances are factory set for LPG or Town Gas. If in doubt, refer to the local gas network operator of gas supplier to confirm gas type at the installation site.
If in doubt, refer to the local gas network operator or gas supplier to confirm gas type at installation site.
Do not modify this appliance.
Do not use or store flammable materials on or near this appliance.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these may cause serious injuries.
You must remove the transit screws before installing the cooktop. See step 8 of installation instructions.

Before you install the appliance, please make sure that

the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance see ‘Gas rate summary’.
a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for alternative means.
the appliance is connected to a 220V – 240V 50Hz (10 A) power supply only and earthed via the power supply cable.
there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the product). This must be accessible after installation. The power supply cable should not touch any metal parts.
if the power supply cable is damaged, it is replaced only by the special cable: Part no. 534906 TRMNL BLOCK-FLEX ASSY HITEMP GOG UK, obtainable from authorised Fisher & Paykel Service Agents. Please see your ‘Service and Warranty’ booklet for contact details.
the supply connection point (gas shutoff valve) is accessible after installation.
the benchtop is made of a heat resistant material.
the installation complies with all the current requirements of National and Local Authority Gas, Electric and other relevant Codes and Regulations.

When you install the appliance

As servicing requires removing of the cooktop from the benchtop we do not recommend flush mounting. To the fullest extent permissible by law, the owner carries all risk for flush mounting of the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out. Fisher & Paykel will not be liable for any costs associated with removing or replacing a flush-mounted and/or sealed-in product, nor for repairing any damage that may be incurred by doing this. Fisher & Paykel does not exclude any statutory liability it may have and which by law cannot be excluded, because of the giving of this notice.
If installed with an approved flexible hose, the hose should not come in contact with the bottom of the appliance or any sharp edges. Flexible hose assemblies should comply with local regulations.
Seal exposed bare edges of the cutout with an oil-based paint or moistureproof polyurethane to prevent possible moisture creeping between the cooktop trim and the benchtop.
Take extreme care not to chip, crack, or break the top glass surfaces during installation. A heavy metal tool or part accidentally dropped on the glass could damage it.
If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our website listed on the cover of this document.

PARTS SUPPLIED

Dual Wok Pan support
(1 per Dual Wok)

| Semi-rapid Pan support
(1) (CG903D only)| Small pan support (1)
(some models only)|

Wok stand
(1 per Dual Wok)

---|---|---|---

Gas Elbow (1)

| Elbow 1/2“ BSP
external thread (1)| Clamping brackets
(4) and screws (4)|

Fibre washers (1)

Installing multiple products

Note: We recommend installing multiple products in separate cutouts, with a minimum 5mm space between the glass edges of the adjacent products. If installing multiple products adjacent to each other within the same cutout, a separate joining strip kit is required for installation.

The kit is available from the nearest Fisher & Paykel Authorised Service Centre or our website listed on the cover of this document.

If installing different products adjacent to each other (eg a wok burner next to an induction cooktop), the minimum clearance measurements for the different products may vary. Always use the greater distance.

GAS RATE SUMMARY

*Nominal pressure with one dual wok burner on High.

PRODUCT & CABINETRY DIMENSIONS

CLEARANCE DIMENSIONS

FLUSH MOUNTING INSTALLATION (OPTIONAL)

DISCARD PACKAGING

REMOVE THE TWO TRANSIT SCREWS

FIT THE ELBOW AND WASHER

LOWER GENTLY INTO THE CUTOUT

FIT CLAMPING BRACKETS BASED ON THE BENCHTOP THICKNESS

SECURE TO BENCHTOP

CONNECT TO GAS SUPPLY

LPG

|

TG

---|---

Make sure the supply pressure is regulated to 2.90 kPa, with all the burners operating at highest setting

|

Adjust to obtain a supply pressure of 1.5 kPa (Hong Kong) or 0.8 kPa (Singapore) with all the burners operating at the highest setting.

ALL Models

Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection is fitted with an isolating valve close to the cooktop.

If connecting the gas with a flexible hose:

Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.
The hose assembly must be certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant local code and regulation requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed. The hose must not be near or in contact with any hot surfaces (e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)

CHECK ALL CONNECTIONS FOR GAS LEAKS

AFFIX DUPLICATE DATA LABEL SOMEWHERE ACCESSIBLE & PLUG COOKTOP IN

FIT PAN SUPPORTS

TEST OPERATION

To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.
Check for a well-defined blue flame without any yellow tipping.
If any abnormality is evident, check that the components of the burner assembly are located properly
If proper operation cannot be obtained, contact Customer Care or your nearest F&P Authorized Service Center.
The cooktop must not be used by the customer until proper operation has been achieved.

FINAL CHECKLIST

✓ TO BE COMPLETED BY THE INSTALLER

Have you installed the clamping brackets?
Have you verified that the type of model (factory-set for NG or LP) matches the type of gas at the site of installation?
Have you used the Elbow supplied?
Have you sealed all connections with gas tape?
Have you leak-tested all connections?
Is the cooktop set to the correct working pressure?
Have you affixed the supplied duplicate data plate label on an adjacent surface accessible to the customer?
Is the cooktop earthed?
Check that the power supply cord is NOT touching the cooktop.

OPERATION:

Do all burners ignite both individually and in combination?
Are the flames consistent and appropriately sized?
Have you demonstrated the basic operation to the customer?

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2021. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer.