FISHER PAYKEL DD60STX6I1 Integrated Single DishDrawer Dishwasher Installation Guide

FISHER – PAYKEL -DD60STX6I1- Integrated -Single- DishDrawer -Dishwasher

SAFETY AND WARNINGS

WARNING!

Electric Shock Hazard Failure to follow this advice may result in electrical shock or death.

• Fitting an integrated panel requires access to electrical service areas. This must be performed by a Fisher & Paykel trained and supported service technician or qualified person.

• Before fitting the front panel, the dishwasher must be disconnected from the power supply.

• After installing the front panel, the installer must ensure that the following components
  are electrically earthed: the panel bracket and any custom metal component (e.g. handle) that extends past the rubber seal.

• This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug.

• Before installing the DishDrawer™ Dishwasher, remove the house fuse or open the circuit breaker.

• The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.

• Do not modify the power supply plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box.

• The dishwasher must be completely enclosed at the time of installation.

WARNING!

Electric Shock Hazard Failure to follow this advice may result in electrical shock or death.

• WARNING – Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly earthed.

WARNING!
Cut Hazard Failure to use caution could result in injury.

•  Take care – panel edges are sharp.

SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

• WARNING!
  To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance.
  Servicing
   Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person.
  Installation

• Installation of this DishDrawer™ Dishwasher requires basic mechanical and electrical skills.

• Installation must comply with your local building and electricity regulations.

• Remove all packaging materials supplied with the dishwasher.

• Be sure to leave these Instructions with the Customer.

• At the completion of the installation, the Installer must perform the Final Checklist.

• This dishwasher is manufactured for indoor use only.

• Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.

• The DishDrawer™ Dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

• The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation.

• Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses.

• If the DishDrawer™ Dishwasher is relocated from one installation site to another it must be kept upright to avoid damage from water spillage.

• Ensure only supplied hoses are used for connection. Old hoses should not be reused.

• Failure to install correctly could invalidate any warranty or liability claims.

• If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

TOOLS AND COMPONENTS

PARTS SUPPLIED

• Keep all packing materials until the unit has been inspected.
• Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage.
• Fisher & Paykel is not responsible for shipping damage.

Supplied

Optional | Comes fitted to the product | DD60DA models only | ****DD60DC & DD60DD models only

TOOLS REQUIRED

Not supplied

INSTALL VIDEO
This video provides an overview of what is needed to install a DishDrawer™ Dishwasher. It is intended as an overview only of the installation process and is not intended to be used as astandalone guide on how to install a DishDrawer™ Dishwasher yourself. Installation should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person.

To access installation videos Scan the QR code with your smartphone or watch online at: fisherpaykel.com/dishdrawer-install

PRODUCT DIMENSIONS

CABINETRY

STANDARD INSTALL ASSISTED OPENING INSTALL

The assisted opening unit should be installed at the centre front of the cavity. For more information on assisted opening installations, refer to fisherpaykel.comCLEARANCESCUSTOM PANEL DIMENSIONS

Material specifications

• Maximum weight of panel must not exceed 9kg (including handle)
• The panel should be adequately sealed to withstand moisture (50°C @ 80% RH). The back and sides of the panel should be completely sealed with a waterproof vapour barrier, such as polyurethane, to prevent damage.
• The back of the panel should be completely flush so that the seal between the panel and the rubber trim is maintained.
• Installation outside these specifications may result in condensation on cabinetry surfaces.

PLUMBING & ELECTRICAL CONSIDERATIONS

Hose and cord lengths

• Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements.

If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher & Paykel drain hose extension kit which will extend the drain hoses by 3.6m (part number 525798).
Water connection

• Recommended water temperature: Cold (maximum 60°C)
• 3/4” BSP (GB20) to suit flat washer

Ensure water connection complies with local plumbing regulations.
Water pressure

• Water softener models: max. 1 MPa (145 psi), min. 0.1 MPa (14.5 psi)

Non-water softener models: max. 1 MPa (145 psi), min. 0.03 MPa (4.3 psi)
Electrical requirements

220-240VAC min 4.8A
Assisted Opening electrical requirements

• A double power socket is required

CABINETRY PREPARATION.

SERVICE ACCESS

• Service holes can be created on either side of the DishDrawer™ Dishwasher cavity as shown below.
• If the hole is created through wood, ensure the edges are smooth and rounded
• If the hole is created through metal, ensure the supplied edge protector is fitted.

MOISTURE PROTECTION

EXTERNAL VENTING PREPARATION

To prevent the build up of condensation produced by your DishDrawer™ Dishwasher, the external venting kit must be installed via one of the following options:

THROUGH SAME CABINET

• A toe kick height of at least 100mm is required.
• A Ø57mm service hole should be created through the side wall following the guidance under ‘Cabinetrypreparation’. In addition to this, a second Ø57mm service hole must be also be created through the shelf and the base of the cavity to route the venting hose through.
• Frameless cabinetry: A 100mm x 200mm cutout must be created at the front of the cabinetry base to secure the duct to.
• Framed cabinetry: A toe kick depth of at least 60mmis required. In addition, a 100mm x 200mm cutout must be created within the adjacent cabinetry base to secure the duct to. This cutout should be set back a minimum of 25mm from the frame edge for optimal venting.
• THROUGH ADJACENT CABINET
• A toe kick height of at least 100mm is required.
• A notched-out Ø57mm service hole should be created through the side wall following the guidance under ‘Cabinetry preparation’.
• Frameless cabinetry: A 100mm x 200mm cutout must be created in the base of the adjacent cabinetry to secure the duct to.
• Framed cabinetry: A toe kick depth of at least 60mm is required. In addition, a 100mm x 200mm cutout must be created within the adjacent cabinetry base to secure the duct to. This cutout should be set backa minimum of 25mm from the frame edge for optimal venting.

THROUGH FLOOR

• There is no minimum toe kick height for venting the DishDrawer™ Dishwasher through the floor belowthe cabinetry, the space below the floor however, must be a sub-area of the house and have adequate airflow.
• A Ø57mm service hole should be created throughthe side wall following the guidance under ‘Cabinetry preparation’. In addition to this, a Ø57mm service hole must be also be created through the shelf, thebase of the cavity and the floor to route the venting hose through.
• The duct is not required for this venting method.
• Ensure all cutout edges are smooth and rounded and the supplied edge protector is fitted if required.

FIT THE TRIM BRACKET

We recommend fitting the trim bracket when installing your DishDrawer™ Dishwasher into a 480mm cavity to conceal any visible gap left between the countertop and chassis.

PREPARE EXTERNAL VENTING

FIT THE VENTING HOSE TO THE DISHDRAWER™ DISHWASHER

**TRIM THE DUCT

** PUSH THE PRODUCT INTO THE CAVITYSECURE THE VENTING HOSE TO CABINETRY

VENTING THROUGH CABINETRY

**VENTING THROUGH FLOOR

** FIT THE CUSTOM PANEL

SECURE TO CABINETRY VIA BRACKETS (METHOD A)

SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B)

PLUMBING & ELECTRICAL CONNECTION

Ø38MM STANDPIPE INSTALLATION

SINK TRAP/WASTE TEE INSTALLATION

INSTALLER CHECKLIST

TO BE COMPLETED BY THE INSTALLER

• Check all parts are installed correctly and are secure.
• Ensure DishDrawer™ Dishwasher is secure and drawer opens and closes freely with no resistance.
• Ensure panel is fitted correctly to the DishDrawer™ Dishwasher
• Ensure any packaging or tape securing the racks and spray arm is removed.
• Check the spray arm is in place, mounted correctly and rotate freely.
• Ensure knock-to-pause module is fitted securely and operating correctly.

Plumbing

• Ensure any knock-outs or plugs in drain connection have been drilled out and drain connection has been made.
• The drain hose joiner must not support the weight of excess hose material. Keep drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the highloop.
• Ensure inlet hose has supplied rubber washer fitted, and that it’s tightened.
• If connecting the drain hose to the sink trap, ensure the highloop is a minimum 150mm higher than the drain hose joiner.
• Water softener models: adjust the water softener setting from the default setting to suit the water hardness of the area. Refer to user guide.
• Ensure water supply is turned off until power is connected and turned on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled.

Electrical

• Ensure all electrical tests have been conducted in accordance with local regulations.

Test operation

• Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the control panel.
• Add three cups of water into the drawer.
• Navigate to RINSE and start the program.
• Repeat for the other drawer.
• After the Rinse cycle has finished, ensure the dishwasher has run and drained correctly.
• Check the water supply has been shut off correctly.
• Check drainage connections for leaks.
• If site is left without power after installation is complete, ensure water supply is turned off to prevent flooding.

TROUBLESHOOTING

A3 fault: excess water remaining above the filter plate after the rinse cycle

• Ensure hose support is correctly installed and drain hoses are routed correctly, refer to ‘Plumbing & electrical considerations’ and ‘plumbing & electrical connection’ for details.

• Check for twisted or kinked drain hoses

• Check for a blocked waste connection.

• Ensure spray arms are mounted correctly and rotate freely.
  A1 fault: no water supply

• Check water is connected and turned on.
  The DishDrawer™ Dishwasher is beeping continuously

• Refer to the ‘Fault codes’ section of your User guide
  No program indicator lights up when the drawer is opened

• Ensure power is connected and is switched on.

• AUTO POWER-ON may need to be activated. Refer to your User guide for details.

Drawer doesn’t close properly

Ensure nothing is obstructing the drawer from closing such as hoses or drawer latches.
Water appears around water supply and drain connections

• Check hoses, connections and existing plumbing for leaks.

Check rubber washer and hose clamp are correctly fitted.
Product is tipping

Ensure the product is secured to the cabinetry.
Front panels are misaligned to surrounding cabinetry

• Check cabinetry is square.
• If a problem occurs that is not listed, refer to your user guide for additional troubleshooting If after checking these points, you still need assistance, please refer to the Service & Warranty book for warranty details or contact us through our website fisherpaykel.com

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer. 592364A 02.21

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Install | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>