thecoopidea CP-TW08 Beans Pro 2 True Wireless Earphones User Manual
- June 5, 2024
- Thecoopidea
Table of Contents
thecoopidea CP-TW08 Beans Pro 2 True Wireless Earphones
CONTENTS
PICK THE RIGHT TIPS
-
Bass Eartips
The enhanced bass frequencies penetrate deeper into the ear canal, reducing the length of the sound waves’ path, for an exceptional listening experience and maximum comfort. Lessens the hissing sounds for a more moderate, heavier sound and that enhances the sound of the music. -
Balance Eartips
The tight fit to the shape of the ear canal gives a super airtight effect, providing powerful noise cancellation and delivering the most realistic, high- resolution music without external interference.
OVERVIEW
- Magnetic Closure
- Strap Holder
- Charging Pin
- Power Indicator
- Eartips
- Charging Interface
- Microphone
- Touch Interface
- LED Indicator
- Type-C Input
NOISE-CANCELING
Tap O on the Left side once to cycle through:
- Active Noise Cancellation
- Ambient Sound Mode ON
- Ambient Sound Mode OFF
Active Noise Cancellation (ANC)
ANC microphone analyzes and blocks out environmental and in-ear noises
respectively.
Ambient Sound Mode
Ambient Sound Mode uses the microphones built into the left and right sides to
allow you to hear the ambient sound even while wearing headphones. Pay
attention to the sounds around you to enjoy listening to music safely.
CHARGING
- Charging Earbuds
- Charging Case (Unplugged)
- Charging the Case
- Charging Case (Charging)
WEARING
PAIRING
Connects to each other automatically.
- L R lash blue-Connecting
- L flashes/1S R flashes off – connected
Bip” sound will be heard on each earbud Make sure your device’s Bluetooth function is turned on Look for ‘THECOOPIDEA BEANS PRO 2″ from the blutooth device list and press connect. The indicator on the Earbuds should be off if it is successfully paired.
CONTROLS
SPECIFICATION
WARNING
Always store the earbuds in the charging case and safely protected them. Avoid storing the earbuds in hot or cold environments to prevent depletion of the battery capacity Avoid storing the earbuds for extended periods of time without recharging them. If the earbuds or the charging case become dirty, it is recommended to clean them with a soft cloth that has been dampened with clean water. The OS version of mobile devices may affect the performance of BEANS PRO 2, it is recommended to update the OS of your mobile device to the latest version before use. Don’t put the BEANS PRO 2 into Charging case while it is moist. Doing so can cause severe damage to the electronics or housing of BEANS PRO 2. BEANS PRO 2 Charging case is not waterproof. Store the product in a dry area. Keep away from fire, heat, and moist and erosive materials. Remove from power source once the product is fully charged. Extended periods of over- charging will decrease battery life. It is strongly recommended to clean and dry BEANS PRO 2 properly when it has been exposed to water and sweat. Do not use rough chemicals such as soap or cleanser to scrub the product. Do not disassemble, damage, or expose the product to water or fire. The warranty will be voided by any misuse of the product. If the battery is expanded or emits a smell, stop using the product immediately.
FCC RULES
NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- this device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
We locate the MIC Logo and ID and the Product name, the Brand ,the Model name on the Color box and the instructions