Nice IBT4ZWAVE BiDi-ZWave Interface Instruction Manual

June 4, 2024
Nice

Nice IBT4ZWAVE BiDi-ZWave Interface Instruction Manual

Nice IBT4ZWAVE BiDi-ZWave Interface Instruction Manual

WARNINGS AND GENERAL PRECAUTIONS

  • CAUTION! – This manual contains important instructions and warnings for personal safety. Carefully read all parts of this manual. If in doubt, suspend installation immediately and contact the Nice Technical Assistance.
  • CAUTION! – Important instructions: keep this manual in a safe place to enable future product maintenance and disposal procedures.
  • CAUTION! – All installation and connection operations must be performed exclusively by suitably qualified and skilled personnel with the unit disconnected from the mains power supply.
  • Important! – If the BUS T4 connection is used for the IBT4N interface, the BiDi-ZWave cannot be connected to the control unit.
  • This product may only be used indoors or protected from weather conditions by control unit’s housing.
  • The product’s packaging materials must be disposed of in full compliance with local regulations.
  • Do not open the device protection housing as it contains non-serviceable electrical circuits.
  • Never apply modifications to any part of the device. Operations other than those specified may only cause malfunctions. The manufacturer declines all liability for damage caused by makeshift modifications to the product.
  • Never place the device near to sources of heat and never expose to naked flames. These actions may damage the product and cause malfunctions.
  • This product is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or who lack experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person responsible for their safety.
  • Make sure that children do not play with the product.
  • Check the warnings in the instruction manual for the motor that the product is connected to.
  • Handle the product with care, being sure not to crush, knock or drop it in order to avoid damage.

PRODUCT DESCRIPTION

CAUTION! – Any use other than that specified herein or in environmental conditions other than those stated in this manual is to be considered improper and is strictly forbidden!

The BiDi-ZWave accessory is a device that – by means of Z-Wave™ communication – allows for controlling the movement and status of Gate&Door- type Nice automations compatible with the BUS T4 (Opera) protocol.

Before proceeding with the product’s installation, make sure to have the following:

  • 1 Nice automation control unit of the Gate&Door catalogue equipped with BUS T4 connector
  • 1 Z-Wave smart home controller
  • If you want to improve the BiDi-ZWave Z-Wave range: 1 antenna compliant with the technical specification (see chapter 10) – not included.

INSTALLATION

Nice IBT4ZWAVE BiDi-ZWave Interface - INSTALLATION

Nice IBT4ZWAVE BiDi-ZWave Interface - INSTALLATION 2

ADDING TO THE Z-WAVE NETWORK

Install the external antenna before powering the device and adding to the Z-Wave network for the device to automatically detect and enable it (use only antennas and cables compliant with technical specification – see chapter 10).

4.1 – Adding manually

Nice IBT4ZWAVE BiDi-ZWave Interface - Adding manually

4.2 – Adding using SmartStart

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. SmartStart product will be added automatically within 10 minutes of being switched on in the network range.

Nice IBT4ZWAVE BiDi-ZWave Interface - Adding using
SmartStart

REMOVING FROM THE Z-WAVE NETWORK

Nice IBT4ZWAVE BiDi-ZWave Interface - REMOVING FROM THE Z-WAVE
NETWORK

EXTERNAL ANTENNA

The BiDi-ZWave is equipped with an internal antenna, but an external antenna can be connected to improve the Z-Wave network range, e.g. when the gate is far away from the house.

Check the technical specification to buy the correct antenna and cable (see chapter 10)!

6.1 – Checking and switching enabled antenna

External antenna will be detected and enabled automatically after powering the device (if not added to the Z-Wave network), but you can switch manually between antennas using the following procedure.

Nice IBT4ZWAVE BiDi-ZWave Interface - Checking and switching enabled
antenna

OPERATION

To control the movement use Z-Wave gateway’s interface or click the S1 button (works in Step-by-Step mode).

RESET

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave gateway and user configuration will be deleted.
Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing described.

Nice IBT4ZWAVE BiDi-ZWave Interface - RESET

LED SIGNALS

Nice IBT4ZWAVE BiDi-ZWave Interface - LED SIGNALS

TECHNICAL SPECIFICATIONS

The product IBT4ZWAVE is produced by Nice S.p.a. (TV). Warnings: – All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C) – Nice S.p.a. reserves the right to apply modifications to the product at any time when deemed necessary, while maintaining the same functionalities and intended use.

Nice IBT4ZWAVE BiDi-ZWave Interface - TECHNICAL
SPECIFICATIONS

PRODUCT DISPOSAL

This product is an integral part of the automation and therefore must be disposed together with the latter. As in installation, also at the end of product lifetime, the disassembly and scrapping operations must be performed by qualified personnel. This product is made of various types of material, some of which can be recycled while others must be scrapped. Seek information on the recycling and disposal systems envisaged by the local regulations in your area for this product category.

Caution! – some parts of the product may contain pollutant or hazardous substances which, if disposed of into the environment, may cause serious damage to the environment or physical health.
As indicated by the symbol alongside, disposal of this product in domestic waste is strictly prohibited. Separate the waste into categories for disposal, according to the methods envisaged by current legislation in your area, or return the product to the retailer when purchasing a new version.

Caution! – local legislation may envisage serious fines in the event of abusive disposal of this product.

Nice SpA
Oderzo TV Italia
info@niceforyou.com

www.niceforyou.com

Nice IBT4ZWAVE BiDi-ZWave Interface - Z-Wave
specification

The device is a Security Enabled Z-Wave Plus product and a Security Enabled Z-Wave gateway must be used in order to fully utilize the product.
The device may be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.
The device works as a Z-Wave signal repeater (all non-battery operated devices within the network will act as repeaters to increase reliability of the network).
Generic Device Type: GENERIC_TYPE_SWITCH_MULTILEVEL (0x11)
Specific Device Type: Not Used

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 3 - Supported Command
Classes

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 4 - Association Command
Class

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 5 - Multilevel Switch Command
Class, Basic Command Class mapping

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 6 - Multilevel Switch Command
Class SET

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 7 - Multilevel Switch Command
Class Report

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 8 - Notification Command
Class

  • Some control units might not support this feature.

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 9 - Protection Command
Class

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 10 - Indicator Command
Class

Nice IBT4ZWAVE BiDi-ZWave Interface - Table 11 - Configuration Command
Class

The device does not support Configuration CC Bulk commands.

Nice SpA
Oderzo TV Italia
info@niceforyou.com

www.niceforyou.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals