JVA WA50 Solar Wi-Fi Anywhere User Guide
- June 5, 2024
- JVA
Table of Contents
Electric Fencing Products
JVA Solar Wi-Fi Anywhere
Quick Start Guide
WA50
PTE2702
Introduction
The PTE2702 JVA Wi-Fi Anywhere (WA50) provides an integrated Wireless Cellular
USB Dongle (Wingle) power supply with a solar battery charger and management
system. This product provides a Wi-Fi network wherever a 3G/4G signal is
available*. The Wi-Fi can then be used to connect an IP device or Internet of
Things (IoT) device to the Cloud (Internet).
The JVA Solar Wi-Fi Anywhere is installed with an ALDI SIM card at the
factory, all you need to do is:
- Register the SIM card
- Connect any Wi-Fi-enabled device to the network provided
This quick-start guide explains how to deploy your WA50 and connect a battery ready for Wi-Fi connections.
*An external cellular antenna (included) may be connected to increase reception. An upgraded YAGI style antenna is available from sales@jvafence.com.au
Specifications
Component | Information |
---|---|
Solar Panel | **Nominal 12v Solar Panel (maximum open-circuit voltage – |
22v DC) Maximum Power 50W
Battery| Nominal 12.8v DC
Minimum Battery size 75Ah
A larger battery may be required if any additional 12v device is connected
to the battery
Outputs(1)| 12v DC SAE Connector
Used for powering the IP Monitor
Component| Information
---|---
Outputs (2)| 12v DC Battery Connector
Alligator clips for battery connection
SIM| Full Size
Wi-Fi| 2.4GHz b/g/n
Up to 10 connections at a time
Network (Huawei E8372)| 3G 850/2100MHz
4GX 700MHz + 4G B1/3/7/21
Antenna Connector| Female SMA
** Ensure the antenna is mounted away from sources of interference such as AC
or high voltage cables.
Troubleshooting
Fault | Likely Cause | Remedy |
---|---|---|
No lights are on | Power is not connected ** | |
**Power wires are re- versed | Check power connec- tions |
Check battery polarity
Batt level flashing| Battery disconnected
Bad battery| Check battery connections
Check battery voltage
USB_5V LED off| USB device drawing too much current| Unplug the USB device,
check for damage/ seek manufacturer advice
Fault| Likely Cause| Remedy
---|---|---
Battery not charging| Solar wiring backward Broken cables Solar panel broken|
Check that the Solar + goes to the left-hand screw terminal
Check that the battery cables are not dammed- aged
Check solar panel for physical damage (broken glass, bent frame, etc.)
Cannot connect to Wi-Fi| The low signal from 3G/4G
Out of Wi-Fi range (~10m)
SIM card not inserted correctly| Check the management page of Wingle
Move closer to Wingle
Re-insert SIM card
If the unit is still not working correctly, contact your nearest JVA distributor for technical support.
Before you start
Activate the SIM card
Activate your SIM card and test it on a mobile phone. The Wi-Fi network allows
a data-only connection, the number of devices connected to the module will
determine how much data will be used.
As a guide, a single IP Energiser or IP Monitor will use less than 1MB per
day, so for connecting a single IP Energiser, an upper limit of 500MB per year
is an option with a lot of headroom.
Deployment and Orientation
-
Unpack the solar kit from its packaging. Look inside the packaging for a set of U-Bolts.
-
Remove the U-Bolts from the zip lock bag and mount them to the top and bottom panel of the bracket.
(A) U-Bolt x 2 (B) Top or Bottom Panel
(C) Washers x 4 (D) Spring Washers x 4 (E) Hex Nut x 4 -
Loosen the 6 bolts on the inside of the frame that is used to hold the solar panel at a right angle. DO NOT completely remove these bolts.
-
Lift the bottom of the solar panel until the attached arms holding it are angled at 90 degrees. Tighten all 6 bolts again from step 3.
-
Attach the red and black eyelet crimps to the battery To find a battery that will suit you, visit our website: https://jva-fence.com.au/solar.php
-
Alternative wiring:
The following diagram shows an alternative method for wiring the Solar Kit. The battery is connected directly to the solar kit and the Wi-Fi device.
The solar kit will have a spare connector (load cable), but the solar kit will still operate properly.
Overview
LED Indicators
D1 (Solar)| Solid on when the solar panel in sunlight
Blinking when the solar panel is in low power conditions Off when no solar
power is detected
---|---
D6 (USB_5V)| Solid on when USB Power is turned on
Batt Level| Bottom LED flashes if no battery is disconnected or bad Shows
battery level from bottom to top: 25% to 100%
JVA Distributors
If you have questions or need further assistance, please email us at sales
@jva-fence.com.au or call
Region | Number |
---|---|
Australia | 0731 030 582 |
South Africa | 0861 782 349 |
World Wide | +61 731 030 582 |
For more information on our complete range of electric fencing products please see the JVA website at https://www.jva-fence.com.au
Tel : +61 (0)499 000 455 Email : sales@jva-fence.com.au
www.jva-fence.com
https://www.jva-fence.com.au/docs/PTE2702_WA50_Quick_Start_Guide_(web).pdf
The JVA Logo is a registered trademark of JVA Technologies
© JVA Technologies
References
- fence.com.au
- Electric Fencing energisers, testers & more for Farms + Security
- JVA International - Electric Fencing Products - Home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>