JVA WA100 Solar Panels User Guide

: June 5, 2024
: JVA

Table of Contents

JVA WA100 Solar Panels
Introduction
Specifications
Troubleshooting
Before you start
Deployment and Orientation
Overview
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JVA WA100 Solar Panels

JVA WA100-Solar-Panels-

Introduction

The PTE2703 JVA Wi-Fi Anywhere (WA100) provides an integrated Wire-less Cellular USB Dongle (Wingle) power supply with a solar battery char-ger and management system. This product provides a Wi-Fi network wherever a 3G/4G signal is avail-able*. The Wi-Fi can then be used to connect an IP device or Internet of Things (IoT) device to the Cloud (Internet). The JVA Solar Wi-Fi Anywhere is installed with an ALDI SIM card at the factory, all you need to do is:

Register the SIM card
Connect any Wi-Fi enabled device to the network provided

This quick-start guide explains how to deploy your WA100 and connect a battery ready for Wi-Fi connections. An external cellular antenna (included) may be connected to increase reception. An upgraded YAGI style antenna is available from [email protected]

Specifications

Component	Information
Solar Panel	Nominal 12v Solar Panel (maximum open circuit voltage – 22v

DC)

Maxmium Power 100W

Battery| Nominal 12.8v DC

Minimum Battery size 150Ah

A larger battery may be required if any additional 12v device is connected to the battery

Outputs(1)| 12v DC SAE Connector

Used for powering the IP Monitor

Component	Information
Outputs (2)	12v DC Battery Connector

Alligator clips for battery connection

SIM| Full Size
Wi-Fi| 2.4GHz b/g/n

Up to 10 connections at a time

Network (Huawei E8372)| 3G 850/2100MHz

4GX 700MHz + 4G B1/3/7/21

Antenna Connector| Female SMA

Ensure antenna is mounted away from sources of interference such as AC or high voltage cables.

Troubleshooting

Fault	Likely Cause	Remedy
No lights are on	Power is not connected

Power wires are re- versed

| Check power connec- tions

Check battery polarity

Batt level flashing| Battery disconnected

Bad battery

| Check battery connec- tions

Check battery voltage

USB_5V LED off| USB device drawing too much current| Unplug USB device, check for damage/ seek manufacturer advice
Fault| Likely Cause| Remedy
---|---|---
Battery not charging| Solar wiring backwards| Check that the Solar + goes to the left-hand screw terminal
| Broken cables| Check that the battery cables are not dam- aged
| Solar panel broken| Check solar panel for physical damage (bro- ken glass, bent frame etc.)
Cannot connect to

Wi-Fi

| Low signal from 3G/4G| Check management page of Wingle
| Out of Wi-Fi range

(~10m)

| Move closer to Wingle
| SIM card not inserted correctly| Re-insert SIM card

If the unit is still not working correctly, contact your nearest JVA distribu- tor for technical support.

Before you start

Activate the SIM card
Activate your SIM card and test it in a mobile phone. The Wi-Fi network allows a data-only connection, the number of devices connected to the module will determine how much data will be used. As a guide, a single IP Energiser or IP Monitor will use less than 1MB per day, so for connecting a single IP Energiser, an upper limit of 500MB per year is an option with a lot of headroom.

Deployment and Orientation

Unpack the solar kit from it’s packaging. Look inside the packaging for a set of U-Bolts.
Remove the U-Bolts from the zip lock bag and mopunt it to the top and bot- tom panel of the bracket.
- (A) U-Bolt x 2 (B) Top or Bottom Panel
- (C) Washers x 4 (D) Spring Washers x 4 (E) Hex Nut x 4
Loosen the 6 bolts on the inside of the frame that are used to hold the solar panel at a right angle. DO NOT completely remove these bolts.
Lift the bottom of the solar panel until the attached arms holding it are angled at 90 degrees. Tighten all 6 bolts again from step 3.
Attach the red and black eyelet crimps to the battery To find a battery that will suit you, visit our website: https://jva-fence.com.au/solar.php
Alternative wiring:
The following diagram shows an alternative method for wiring the Solar Kit. The battery is connected directly to the solar kit and the Wi-Fi device.
The solar kit will have a spare connector (load cable), but the solar kit will still operate properly.

Overview

JVA WA100-Solar-Panels-8

LED Indicators

D1 (Solar)| Solid on when solar panel in sunlight

Blinking when solar panel in low power conditions Off when no solar power detected

---|---
D6 (USB_5V)| Solid on when USB Power is turned on
Batt Level| Bottom LED flashes if no battery is disconnected or bad Shows battery level from bottom to top: 25% to 100%

JVA Distributors
If you have questions or need further assistance, please email us at sales @jva-fence.com.au or call