JVA WA20M Solar Panels User Guide
- June 5, 2024
- JVA
Table of Contents
JVA WA20M Solar Panels
Introduction
The PTE2701 JVA Wi-Fi Fence Monitor provides an integrated Wireless Cellular
USB Dongle (Wingle) power supply with a solar battery charger and management
system.
This product provides a Wi-Fi network wherever a 3G/4G signal is avail-able*.
The Wi-Fi can then be used to connect an IP device or Internet of Things (IoT)
device to the Cloud (Internet).
The JVA Solar Wi-Fi Fence Monitor is paired with the Wingle at the fac-tory,
all you need to do is:
-
Register the SIM card
-
Add the Fence Monitor to the IP Energiser Controller app on your iOS or Android device
This quick-start guide explains how to connect your PTE2701 to a fence and turn it on.- An external cellular antenna (included) may be connected to increase reception. An upgraded YAGI style antenna is available from sales@jva-fence.com.au
Specifications
Component | Information |
---|---|
Solar Panel | **Nominal 12v Solar Panel (maximum open circuit voltage – |
22v DC)**
Maxmium Power 20W
Battery| Nominal 12.8v DC
Minimum Battery size 18Ah
A larger battery may be required if any addiontal 12v device is connected to the battery
Component | Information |
---|---|
Outputs(1) | 12v DC SAE Connector |
Used for powering the IP Monitor
Outputs (2)| 12v DC Battery Connector
Alligator clips for battery connection
SIM| Full Size
Wi-Fi| 2.4GHz b/g/n
Up to 10 connections at a time
Network (Huawei E8372)| 3G 850/2100MHz
4GX 700MHz + 4G B1/3/7/21
Antenna Connector| Female SMA
Ensure antenna is mounted away from sources of interference such as AC or high voltage cables.
Troubleshooting
Fault | Likely Cause | Remedy |
---|---|---|
No lights are on | Power is not connected |
Power wires are re- versed
| Check power connec-
tions
Check battery polarity
Batt level flashing| Battery disconnected
Bad battery
| Check battery connec- tions
Check battery voltage
USB_5V LED off| USB device drawing too much current| Unplug USB device, check
for damage/ seek manufacturer advice
Fault| Likely Cause| Remedy
---|---|---
Battery not charging| Solar wiring backwards| Check that the Solar + goes to
the left-hand screw terminal
| Broken cables| Check that the battery cables are not dam- aged
| Solar panel broken| Check solar panel for physical damage (bro- ken glass,
bent frame etc.)
Cannot connect to Wi-Fi| Low signal from 3G/4G| Check management page of
Wingle
| Out of Wi-Fi range (~10m)| Move closer to Wingle
| SIM card not inserted correctly| Re-insert SIM card
If the unit is still not working correctly, contact your nearest JVA
distributor
for technical support.
Troubleshooting the IP Monitor
Fault | Liklely Cause | Remedy |
---|---|---|
Status LED off | Power failure | Check connections and battery level |
Status LED green | Normal operation, connected to internet and ready to | |
operate | No action necessary | |
1 Red flash | IP Monitor is not con- nected to Wi-Fi, this is factory default | |
mode | Configure the IP Monitor to connect to the Wingle’s Wi-Fi network | |
Fault | Liklely Cause | Remedy |
--- | --- | --- |
2 Red flashes | IP Monitor has re- ceived Wi-Fi configu- ration and is attempt- |
ing to connect to
Wi-Fi network
| If persistent (more than 2 minutes) Factory default and try to configure
again
3 Red flashes| IP Monitor is connect- ed to Wi-Fi and is con- nected to the
internet| This should not dis- play for more than 20 seconds, after which it
will turn green. No action necessary
4 Red flashes| Failed to connect to Wi-Fi, the unit will try again| If this
persists, fac- tory default and try to configure again. If more than 10m away
from Wingle, move closer.
5 Red flashes| IP Monitor has incor- rect password| Default the IP monitor
and re-configure
If the unit is still not working correctly, contact your nearest JVA distributor for technical support.
Before you start
Activate the SIM card
Activate your SIM card and test it in a mobile phone. The Wi-Fi network allows
a data-only connection, the number of devices connected to the module will
determine how much data will be used.
As a guide, a single IP Energiser or IP Monitor will use less than 1MB per
day, so for connecting a single IP Energiser, an upper limit of 500MB per year
is an option with a lot of headroom.
Overview
D1 (Solar)| Solid on when solar panel in sunlight
Blinking when solar panel in low power conditions Off when no solar power detected
---|---
D6 (USB_5V)| Solid on when USB Power is turned on
Batt Level| Bottom LED flashes if no battery is disconnected or bad Shows
battery level from bottom to top: 25% to 100%
Configure IP energizer Controller App
Download the IP Energiser Controller application (IPEC) from the app store or
google play.
Add a site to your IPEC app:
- Press the menu hamburger at the top left
- Press “Add Site”
- Name the Site anything appropriate e.g. “North East 6km”
- Fill in the Unit Serial Number with the serial number of the IP Monitor. This can be found on the bottom at the back of the IP Monitor.
- Fill in the Unit Password with the same Serial Number used just before. The default password set by factory is the serial number of the IP Monitor.
- Select the “Device Type” as “IP Monitor”
- Set alarm thresholds for voltage and current accordingly. The IPEC app will notify you if the IP Monitor hits or exceeds these thresholds.
- Press “OK”
Connect IP Monitor
Option 1 – Monitor the end of a fence
- Turn off Energiser before starting
- Green Terminal to Fence Ground (Earth)
- Yellow Terminal to Fence Live
Red Terminal (nothing connected) Advantages
-
End of Fence Voltage Monitoring
-
Cut detection
-
Fence Load detection
Limitations -
No Current monitoring
-
No fence armed state control1
1. Relay function not available on IPM variant (PTE2606) – requires IPM-R
Option 2 – Monitor from the start of the fence(s)
Turn off Energiser before starting
- Green Terminal to Fence Ground (Earth)
- Yellow Terminal to Fence Live
- Red Terminal to Energiser
Output (high voltage) Advantages
-
Current Monitoring
-
Voltage Monitoring
-
Ability to control the fence armed state1
Limitations: -
No cut detection
-
Relay function not available on IPM variant (PTE2606) – requires IPM-R
Battery Connection and First Power On
Connect the battery to the PTE2701 by the included battery connection cables.
Ensure that the positive is connected to the red connector and the negative to
the black connector.
Once connected, the Batt Level indicator lights will show the approximate
voltage level of the battery.
If everything is connected, the IP Monitor will have a Green status light. This will now be available and online in the IP Energiser Controller application.
JVA Distributors
If you have questions or need further assistance, please email us at sales@
jva-fence.com.au or call
Region | Number |
---|---|
Australia | 0731 030 582 |
South Africa | 0861 782 349 |
World Wide | +61 731 030 582 |
For more information on our complete range of electric fencing products please see the JVA website at https://www.jva-fence.com.au
Tel : +61 (0)499 000 455 Email : sales@jva-fence.com.au www.jva-fence.com
References
- fence.com.au
- Electric Fencing energisers, testers & more for Farms + Security
- JVA International - Electric Fencing Products - Home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>