GRUNDIG GSB 910 SW 2.1-Channels 80W Soundbar User Manual

GRUNDIG -GSB 910 SW 2.1-Channels -80W -Soundbar

REMOTE CONTROL

AT A GLANCE

PREPARATION/CONNECTION

Preparation
Activate the remote control battery

1.  Remove protection film from the battery com-partment.
2. The remote control is now functional.

Change remote control batteries (TYPE AAA)

Note:
If your device no longer responds to the remote control commands, the battery may be dead. It is imperative that dead batteries be removed. We do not assume liability for damage caused by leaked batteries.

Caution:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

1. Hold the remote control with the back side fac- ing up.
2. Push the detent of the battery holder to the right and remove battery holder.
3. Remove used battery and insert new battery into the battery holder, positive pole facing up-ward.
4. 4 Push battery holder into the remote control until it clicks into place.

Connecting
Connect Soundbar to the LCD TV

1.  Connect a standard audio lead to the AUX INPUT« jacks of the Soundbar.
2.  Please be aware of the left and right chan nels when doing so (white = left channel, red = right channel).
3. 2 Connect audio lead to the audio output jacks of the LCD TV.

Connect external device
An external device, such as a MP3-Player for ex-ample, can be connected to the »AUX IN« jack.

1. Connect a standard audio lead to the AUX IN« jack of the Soundbar.

2 Connect adapter cable to the external device.
Note:
The LCD TV can also be connected via the »AUX IN« jack if it is not equipped with audio output jacks. In such cases please use the headphone jack.
Connect mains cable
Check that the mains voltage indicated on the type label (on the back of the device) corresponds to the local mains voltage. If this is not the case, please consult your specialist dealer. 1 Plug mains cable plug into the socket (100 – 240V~ 50/60Hz).
Caution:

•  The Soundbar is connected to the mains via the mains cable. If you want to disconnect the Soundbar from the mains completely, you must pull the mains plug.
•  Please ensure that the mains cable is freely accessible during operation and is not obstructed by any other objects.

Subwoofer Connection

1. Make sure the AC power cord is connected to a power supply securely.
2. Subwoofer have wireless bluetooth to receive the audio signal from the sound bar. When the blue indicator flashing, the subwooferis in searching bluetooth signal status, the blue indicator keeps lighting means bluetooth was connected, if the subwoofer can not connect with the soundbase automatically, please press pair button on the rear panel of subwoofer to reconnect.
3. The subwoofer will memories the sound bar and repaired automatically when you power off the subwoofer then power on.

WALL MOUNTING

In order to prevent injuries,the sound base device must be securely fastened to the wall in accordance with the below installation instructions.
Caution:

• The ground must be firm and capable of handling the load.
• Use mountings that are appropriate for the weight of the device.

For wooden or hollow wall structures use suitable plugs and screws. Seek advice from a specialist dealer.
Warning:

In order to prevent injuries, the device must be securely fastened to the wall in accordance with the installation instructions.
Note:

• Installation of the Soundbar GSB 910 SWfor professional use (e.g. in a bistro) must only be carried out by an electrically qualified person, in accordance with the applicable construction regulations as per VDE 0100.
• Drill the two holes(about 6mm diameter ) in the wall and keep the distance between drill holes of the sound bar is 500mm (Diagram 1).
• Insert the two plugs supplied into two drilled holes and then insert two screws supplied into two holes and tighten (Diagram 2).
• Take care to leave 4 mm between the screw heads and wall (Diagram 3).
• Use the assembled sound bar to hang on the setscrews on the wall (Diagram 4).

OPERATION

IN/LINE IN
This sound base have two extra groups of audio input terminals. You can input the analogue stereo audio signals from extra devices such as VCD, CD, VCR, DVD player, etc. Use the audio cable to connect the stereo audiooutput terminals of a VCD, CD, VCR,DVD player to the stereo input terminals AUX IN/LINE IN of this sound base. Its corresponding signal source is AUX IN/LINE IN which can be available by pressing [SOURCE] on the remote control.
Optical Input
Soundbar Connect LCD TV (digital Signal)

1. Connect a commercially available optical cable to the »OPTICAL« jack of the Soundbar.
2. Connect the optical cable to the sound output socket of the LCD TV (optical, PCM signal).

Note:
The TV audio output must be set to PCM.
Soundbar Connect LCD TV (analoge Signal)

1. Connect a commercially audio cable to the »R – AUX IN – L« jack of soundbar left and right channel. (white = left channel, red = right channel)
2.  Connect the audio cable to the sound output socket of the LCD TV

Note:  Choose appropriate analoge audio output
on TV.
ARC(AUDIO RETURN CHANNEL)
ARC is audio return channel function,it is used in digital audio output of liquidcrystal display television in order to get the optimal synchronous sound quality . Use the HDMI cable to connect the HDMI-ARC input port of this sound base to the ARC output port of the liquid-crystal display television.

Your device can be paired with all current, Bluetooth-
enabled devices applying to smartphones,
laptops and tablet PCs for example.

1. Press standby button » 8 « to power on the sound base.
2. Press source button » « to switch the corresponding bluetooth mode.
3. The bt will be flashing quickly in the display .. screen.
4. The sound base is in searching bluetooth signa status.
5. Use your smart phone to search the bluetooth signal of the sound base.
6. Select ”Grundig Soundbar 2.1” on your list.
7. The sound base will synchronize to play songs on your mobile phone while the bt keep solid light in the display screen means to be connected successfully.

OPERATION

Disconnected the bluetooth on the smart phone to switched off the bluetooth connection.
Note:

• Bluetooth connection range in 10 meters
• The model ”Grundig Soundbar 2.1” in your device was not deleted.
• In bluetooth mode, »eII«, » «, » «, »+«, »–« etc. are also active.

Remote control operation

1. Insert the batteries into the remote control.
2. Point the remote control at the remote sensor on the front panel.
3. The sound base is in searching bluetooth signa status. The remote control works within a distance of about 8 metres from the sensor and within an angle of about 30 degrees from the left and right side.

Battery installation

1.  Remove the battery compartment cover on the back of the remote control.
2. Load one AAA/1.5V battery into the battery compartment making sure that the battery have been inserted with the correct polarities matching the symbols +, – as indicated inside the battery compartment.

Note:

• Remove the battery when you do not intend to use the remote control for a long time.
• Weak batteries can leak and severely damage the remote control.
• The battery must not be exposed to excessive heat source, such as sunshine, fire or any other things like that.
• Be environmentally friendly and dispose of batteries according to your government regulations.

INFORMATION

Technical Information
This device is noise-suppressed according to the applicable EU directives. This product fulfils the European directives 2014/53/EU, 2009/125/ EC and 2011/65/EU. You can find the CE declaration of conformity for the device in the form of a pdf file on the Grundig Homepage www.grundig.com/downloads/doc

• Power supply: 100-240V~ 50/60Hz
• Max. power input: Power consumption: 20W, Standby ≤ 0.5 W
• Power output : DIN 45324, 10% THD 2 x 20 W
• Frequency response: 20 Hz – 20 kHz
• BT frequency : 2402 – 2480 MHz
• BT maximum output power : 7.2 dBm
• S/N ratio: ≥ 70 dB
• Separation: ≥ 45 dB
• Dimensions and weight: W x H x D 88 x 6.2 x 8 cm
• Weight approx. 1.88 kg
• Subwoofer Power supply: 100-240V~ 50/60Hz
• Max. power input: Power consumption 25 W, Networked Standby ≤ 2 W
• Power output: DIN 45324, 10%THD 1x40W
• Dimensions and weight: W x H x D: 20.0 x 32.0 x 23.0 cm
• Weight approx. : 3.0 kg
  Technical and design modifications reserved!

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used devices must be returned to official collection point for the recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was purchased. Each household performs an important role in recovering and recycling of old appliances. Appropriate disposal of used appliances helps prevent potential negative consequences for the environment and human health.
Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Package information
Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

References

• Grundig Global
• Grundig Global
• SERBÄ°S
• Grundig Türkiye (@grundigturkiye) • Instagram photos and videos

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>