virtufit TR-50i Totally Foldable Treadmill User Manual

virtufit TR-50i Totally Foldable Treadmill

SAFETY INSTRUCTIONS

WARNING:
Before beginning any exercise program consult your physician. This is especially important for people who are over 35 years old or who have pre- existing health problems. Read all instructions before using any fitness equipment. Do not operate this device without properly fitted guards, as the moving parts can present a risk of serious injury if exposed.

ATTENTION

• It is important to read this entire manual before assembling and using the device. Safe and effective use can only be achieved if the device is assembled, maintained and used properly. It is your responsibility to ensure that all users of the device are informed of all warnings and precautions.
• Before starting any exercise program, you should consult your doctor to determine if you have any medical or physical conditions that could put your health and safety at risk, or prevent you from using the device properly. Your doctor’s advice is essential if you are taking medication that affects your heart rate, blood pressure or cholesterol level.
• Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, extreme shortness of breath, lightheadedness, dizziness or feelings of nausea. If you do experience any of these conditions you should consult your doctor before continuing with your exercise program.
• Keep children and pets away from the device. The device is designed for adult use only.
• Use the device on a solid, flat-level surface with a protective cover for your floor or carpet. To ensure safety, the device should have at least 0.5 meters of free space all around it.
• Before using the device, check that the nuts and bolts are securely tightened.
• The safety of the device can only be maintained if it is regularly examined for damage and/or wear and tear.
• Always use the device as indicated. If you find any defective components while assembling or checking the device, or if you hear any unusual noises coming from the device during use, stop immediately. Do not use the device until the problem has been rectified.
• Wear suitable clothing while using the device. Avoid wearing loose clothing that may get caught in the device or that may restrict or prevent movement.
• The max user weight is 120 KGS. Braking ability is independent of speed.
• The device is not suitable for therapeutic use.
• Care must be taken when lifting or moving the device so as not to injure your back. Always use proper lifting techniques and/or seek assistance if necessary.
• Please keep the space at least 1 to 2 meters at the end of the base frame to escape any accidents!
• Place the device on a clean and flat surface. Do not place the device on a thick carpet.
• The device is for indoor use and not for outdoor use to prevent damage. Keep the storage location dry, clean and flat. It is forbidden to use the device for purposes other than training.
• Only use the machine in an environment with an ambient temperature between 10 °C and 35 °C. Only store the device at an ambient temperature between 5 °C and 45 °C.

A warranty claim is excluded if the cause of the defect is the result of:

• Maintenance assembly and repair work are not carried out by an official dealer.
• In the event of improper use, neglect, and/or poor maintenance.
• Failure to maintain the device in accordance with the manufacturer’s instructions (see the enclosed manual).

CHECKLIST

TOOLKIT

When you open the carton, and you will find the below parts in the carton:

DESCRIPTION QTY

• 1 Mainframe 1
• 12 Allen key 5mm 1
• 51 Bold 4
• 64 Lock washer 6
• 71 Security key 1
• 72 Oil bottle 1
• 70 Bolt 2
• 85 MP3 cable 1

NOTE: Do not connect the appliance to the mains before it has been completely set up.

ASSEMBLY INSTRUCTIONS

Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and the device. Some parts (bolts, screws, etc.) are already attached to/in the device.

Error message: Ensure that all cables are carefully attached. The aluminum legs are very sensitive and must remain straight. Do you receive an error message after mounting your device? Then you have to straighten these aluminum legs again, this may cause the error message to disappear.

Socket screws: The device contains socket screws, make sure that the allen key is firmly in the bolt before you apply force to the key. In this way you prevent the head of the socket head screw from being rotated.

STEP 1

• Unscrew the adjusting knob on both sides of the frame respectively(suggest unscrewing 3 circles)
  to make the lower ends of upright tubes flick from the mainframe.

• Uplift the handlebar to the slot corresponding to the hinge of the mainframe.

STEP 2

• After finishing the uplifting, screw the hand knob according to the direction as the arrow shows.

STEP 3

• Use the M6 screws (the screw is pre-assembled on the upright tubes) to fx the console together with ube. the upright tubes, then connect the connector wires of the right handrail and upright tube.

Attention: There are wires on the front and backside of the connector. Be careful not to pinch the wires. Also pay attention tot this when folding and unfolding when using the treadmill

STEP 4

• console in the horizontal direction and clip the pull pin of the left and right handrails into the holes on the upright tubes.

STEP 5

• Put the safety key (4) on the yellow area on the console.
• The switch can be found on the rear of the TR-50i at the bottom near the power input.

FOLDING INSTRUCTIONS

NOTE: Store your machine in a dry area away from children and high traffic areas as shown in the illustration. Be sure it is secure and cannot fall onto small animals or children.

RUNNING BELT ADJUSTMENT

1. Running belt deviates to left: Start the machine, set the speed at 2-3 km/h without a load on the belt, and use the Allen key to turn the screw 1/4 turn (see fig. 1). Then allow the machine to run without a load for 1-2
   minutes. Repeat the process until the belt becomes central.

2. Running belt deviates to right: Start the machine, set the speed at 2-3 km/h without a load on the belt, and use the Allen key to turn the screw 1/4 turn (see fig. 2). Then allow the machine to run without a load for 1-2 minutes. Repeat the process until the belt becomes central.

3. Running belt jam: If the running belt is in dead condition, use the Allen key to turn the screw 1/2 a turn both left and right until the jam is solved (see fig 3).

TECHNICAL PARAMETER

GROUNDING METHOD

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

NOTE:

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
• Do not modify the plug provided with the product – if it will not t the outlet, have a proper outlet installed by a qualified electrician.
• Make that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

MAINTENANCE

Safe and effective use can only be achieved if the device will be assembled and maintained well. It is your responsibility to ensure that the equipment is regularly maintained. Parts that are already used and/or damaged must be replaced before continuing use. The rower machine may only be used indoors and stored away, prolonged exposure to weathering and changes in temperature/humidity can have a serious impact on the electrical components and moving parts of the device.

DAILY MAINTENANCE

• Clean and remove sweat after each use Do not use aggressive cleaning agents and ensure that the device remains free of moisture.
• Check that the rail and the wheels under the seat are free from dust and dirt.

SEMI-ANNUAL MAINTENANCE

• Inspect all bolts and nuts in connection with moving parts of the device, and tighten as required.
• Check the mobility of moving parts and components of the user equipment, silicone spray if necessary.

ATTENTION

Always unplug the treadmill power cord before cleaning or servicing the equipment.

Cleaning: General cleaning of the device will extend the life of the treadmill. Hold clean the treadmill by dusting regularly. Be sure to clean the exposed area of the belt and the foot rails of the treadmill on both sides.

In addition, wear clean shoes to reduce the risk of contamination of the treadmill. Remove the hood at least once a year to vacuum underneath.

LUBRICATING THE BELT

This treadmill is equipped with a pre-lubricated, low-maintenance deck system. The belt/ deck friction may play a major role in the function and life of your treadmill, thus requiring periodic lubrication. We recommend a periodic inspection of the deck. You need to contact our service center if you find the damage to the deck.

We recommend lubrication of the deck according to the following timetable:

• Light user (less than 3 hours/ week) annually
• Medium user (3-5 hours/ week) every six months
• Heavy user (more than 5 hours/ week) every three months

The best indicator is to lubricate when the walking platform feels dry. We recommend that you buy the lubrication from our distributor or directly to our company.

NOTE: Any repair needs a professional technician.

• We suggest that you should cut off the power for 10 minutes after keep running for 2 hours so that it’s good for maintaining the treadmill.
• For avoiding the slipping during running, the belt is not too loose; for avoiding the more abrasion between the roller and belt and to maintain the machine’s good running, the belt not be too tight. You can adjust the distance between plates and belt, the belt be away from the plates about 50-75 mm on both sides, if the best not too tight and loose.

We strongly recommend that you do the following

• Switch off and remove the power cable from the wall after every use, especially if children are present.
• Clean your treadmill after use.
• Use a dry cloth to clean the control panel and areas around the power switch. Use a soft clean cloth and cleanser to remove stubborn stains and dirt off the running belt.
• Tighten the running belt once a month.
• Keep your treadmill in a safe dry place away from heat and water.

USAGE OF SILICONE OIL

Pull up tightly the running belt. Then put the silicone oil on the running board. Then start the machine to run for 3 minutes without loading. It is better to maintain this every 30 hours working of the machine. This can save the lifetime of parts properly.

We recommend that you do the following:

• Disconnect the power cord after every use, especially when children are present.
• Clean the treadmill after use.
• Use a dry cloth to cover the control panel and areas around the on/off switch clean.
• Use a soft clean cloth and detergent to remove stubborn stains and dirt from the treadmill.
• Tighten the treadmill once a month.
• Keep your treadmill away from heat and water in a safe, dry place.

Regular maintenance prolongs the life of your treadmill and prevents injury!

TROUBLESHOOTING

ERROR CODES

E01

| Problem: Signal failed between computer and console.

Solution: Check if the wire is undamaged and properly connected, if so replace the circuit board of the computer or console.

E02

| Problem: The motor voltage is not recognized by the controller.

Solution: Check if the positive and negative cable of the motor is properly connected with the terminal interface of the controller, if that is okay, check if the end tube that is on the controller and peripheral equipment is damaged. Then consider replacing the console or motor.

E03

| Problem: Speed display is not recognized by the console when the engine is running.

Solution: First check if the engine is running when the machine is started and it shows E03, then see if the light sensor is good, see if the wire of it is tight or if the transition between the light sensor and the 4 white pins of the controller are well connected. If all of the above is correct, see if the area around the 4 white pins on the peripherals are damaged, if not consider replacing the console and circuit board. If the engine is not running when you    start the machine, and it shows E03, check if the engine is broken and consider replacing   the engine.

E05

| Problem: When the motor is running, the voltage exceeds the protection value.

Solution: Check that the motor is in good condition and that there is something stuck between the conveyor belt which increases the motor resistance. If all of the above is correct, replace the console.

E07

| ****

Problem: Security key signal is not recognized by the computer, showing E07 or “——– ”.

Solution: Check if the magnetic parts of the safety key are good plugged in.

ERR

| Problem: The safety key is not attached.

Solution: Put on the safety key.

No power

| Solution:

•            Check if the fuse is good.

•           Check that the entire connection cable is properly connected to the console.

Abnormal motor control

| Solution:

•            Check if the motor is normal or replace the motor.

•            Confirm that the motor has no problems.

Engine burned out

| Solution:

•            Check if the console is also burnt out.

•            Replace the motor.

•            Replace the console.

Slope is not right

| ****

Solution: Check if the slope motor wire and 3 pin wire is properly connected to the console, if that is okay, please do as follows:

1.   Remove the computer cable installed on the console (security key), turn

on the device, press the small key the right corner of the controller for 2 seconds.

2.   Release the button, the ramp motor will detect itself stating it the device

at the highest incline and after a while again will drop to the lowest incline.

3.   If the motor hits the ground after 3 seconds, it is automatic detection

process over.

4.   After automatic detection, close the computer (or security key) on, operate the computer function and test that the incline function works.

5.   Or replace the console.

Power failure| Solution: Check if the wire is connected properly.

No screen display

| Solution:

•            Check that the voltage is correct.

•           Check if the power supply is 8V, change the console, if not, change the computer.

LCD screen display

| Solution:

•            Check if the power is good.

•            Check if the power supply is 8V, change the console, if not, change the computer.

Sceen display is poor

| ****

Solution: First turn off the device, restart the engine, see if the screen is back to normal, if not, take out the computer and the fixed PCB.

Solution: First turn off the device, restart the engine, if the problem is still not resolved, replace the computer.

Backlight is not bright

| Solution:

•            Turn off the device, restart the engine.

•           Start the computer, see if the cable is properly connected, see if it background light is damaged or not.

•            Change the computer.

USB card does not play the music

| Solution: Test if the MP3 connection is normal, if it does not work normally, open the computer to see if there is a good connection with the amplifier.

Connection is good, just like the MP3 connection, replace the USB to try again or replace the computer.

Safety pin has no effect

| Solution:

•            Check that the safety pin is properly inserted.

•            Take out the computer, make sure the switch and wire are in good condition or replace the computer.

Button has no function

| Solution:

•            If it’s just one button that doesn’t work, open the computer program,see if any key is damaged or replace the computer.

•            If most buttons do not work, turn the computer back on see if the keys

still don’t work or replace the computer

Push button without influence

| Solution:

•            Wash your hands and test again.

•           Check that the cables of the handle, which measure the heart rate, damaged and that they are properly connected to the connector.

•            Change the circuit board or computer.

Button of handle has no function

| Solution:

•           Check that the cables of the handle, which measure the heart rate, damaged and that they are properly connected to the connector.

•            Change the computer.

Hand sensors do not work

| Solution:

•            Wash your hands and hold the handle again.

•            Check if the thread of the handle is good.

•            If connection is good, change the computer.

The button on the handle does not work

| Solution:

•           Check that the handle wire is good and the connection is good is connected.

•            Please replace the handle.

CONTROL PANEL

CONSOLE

seconds.
+/-| Press the “+” button to speed up the tempo and the “-” button to decrease the tempo. The maximum speed is 12 km / h and the minimum speed is 1 km / h.

MODE

| Press the “MODE” key, the screen displays “SPEED”, “TIME” and “CALORIES”. The display will light up every 5 seconds with data from “SPEED”, “TIME” and “CALORIES”.
BUTTON| FUNCTION
---|---

PROGRAM

| ****

Press this button to select a program of manual mode: P1 — P15—— “FAT”.

MODE

| When the machine is ready, press this button to choose the mode: time mode countdown, distance mode countdown, calorie mode countdown.

START

| ****

Press this button to start the machine, the machine will start at the lowest speed or with the speed of the standard program after 3 seconds.

STOP

| ****

Press this button to stop the machine, the machine will come to a slow stop.

SPEED ^/v

| Sets the speed. Press this button to adjust the speed while running and adjust it when you stop.
SPEED (3, 6, 9, 12)| ****

Adjusts the speed in quick steps.

BUTTON HANDLE (R)| ****

Speed button.

BUTTON HANDLE (L)| ****

“START / STOP” button.

HEARTBEAT TEST

| ****

The heart rate is displayed on the screen after 5 seconds if you hold the handle with both hands. To  get the heart rate more accurate, please test when the machine stops and hold the handles for more than 30 seconds. The heart rate shown may differ from reality.

SAFETY KEY
Pull out the safety cord and the treadmill will stop immediately. All windows will display “—”, the buzzer will sound “B-B -” 3 times, then the walking belt will stop. Attach the tip of the safety cord magnet to the computer and the treadmill will start moving again.

PROGRAMS

The display monitor has 12 programs from P1-P12. While on standby mode, press “PROG” to set the programs then press “START” to start the machine. For example, after activating the treadmill, press “PROG” immediately to enter the programs. Or press “STOP” 2 times to get into standby mode. Below you can see the programs. The horizontal line represents time, each dot represents 1,5 minutes. The vertical line stands for speed, each dot represents 1km/h. Each program lasts 30 minutes.

While the machine is in use and running, during the auto programs the (-) and (+) keys are not available.
If you want to stop the auto programs, select “STOP” or remove the safety key, then turn on again or place the safety key back on. Then select the desired speed. For emergency stop, please pull out the safety key. The machine will stop very slowly. Pull out the safety key and the screen will show “Err”, put it back and on it will show “OFF”. Press the “STOP” key to stop the machine after using.

APP INSTRUCTIONS

INSTRUCTION

1. A QR code scanner app is required to scan the QR code with an Android or IOS phone or tablet. This app can be downloaded in the App Store or Google Play Store.

2. Scan one of the QR codes below to go directly to the place in the App Store or Google Play Store where
   the app is located and can be downloaded.

3. Scan the QR code on the right to go to the user manual of the app. The manual describes step by step how the app should be connected to the device, how the app works and what the options are.

FIT SHOW

EXPLODED DRAWING

PARTS LIST

TRAINING INSTRUCTIONS

A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down.
Do the entire program at least two and preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or five times per week.

WARMING UP

The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength trainingx or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place.

STRETCHED

Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic training session is very important. Muscles stretch more easily at these times because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held for 15 to 30 seconds.

COOLING DOWN

The purpose of cooling down is to return the body to its normal or near- normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>