HIGROUND V1 Wireless Dongle User Manual

May 15, 2024
HIGROUND

HIGROUND-logo

HIGROUND V1 Wireless Dongle

HIGROUND-V1-Wireless-Dongle-product

Specifications

  • Model: Higround Wireless Mouse V1
  • Model Number: HVIN: HGMOUSE1, HGMOUSE2, HGMOUSE3
  • Product Type: Wireless Mouse

Overview

  • A. Left Mouse Button
  • B. Right Mouse Button
  • C. Scroll Wheel
  • D. Side button 1
  • E. Side button 2
  • F. Top Indicator LED
  • G. DPI Button
  • H. DPI Indicator LED
  • I. Power Switch
  • J. Wireless Dongle
  • K. Dongle Indicator LED
  • L. USB Cable

HIGROUND-V1-Wireless-Dongle-fig-1

Setup

Initial Setup
Connect the L USB cable to the J Wireless Dongle and your PC. Turn ON the mouse with the I Power Switch

Pairing
The mouse and wireless dongle are already paired out of the box. Should you need to repair them, follow these steps.

  1. Unplug J Wireless Dongle.
  2. With the mouse powered on, press and hold A LMB, B RMB and C Scroll Wheel together for 3-5 seconds. The F Top Indicator LED will start blinking.
  3. Plug in the J Wireless Dongle.
  4. F and K LED will turn Green when paired.

Usage & Battery

Connection Status
The K Dongle Indicator LED will show the connection status of the mouse and J Wireless Dongle.
Green – Connected
Red – Disconnected / Sleep Mode Flashing Blue – Connecting

Battery Level & Charging
While in use, the mouse F Top Indicator LED denotes the battery level.

  • 100% – 75% – Green

  • 74% – 50% – Blue

  • 49% – ?% – Orange

  • ?% – Red

  • Flashing Red?

  • To charge, plug in an L USB Cable to the mouse.

  • F Top Indicator LED shows status.

  • Slow Blink Green – Charging Static Green – Fully Charged

Settings

DPI Adjustments
To change the DPI, press the G DPI Button.
The H DPI Indicator LED will light up:

  • 400 DPI – Red
  • 800 DPI – Green
  • 1600 DPI – Blue
  • 3200 DPI – Orange
  • 6400 DPI – Purple

LOD – Lift Off Distance
To adjust the LOD, press and hold B RMB, C Scroll Wheel, and D Side Button 1 together for 3 seconds. The F Top Indicator LED will flash:

  • 1mm – Cyan
  • 2mm – Purple

Motion Sync

To enable/disable motion sync, press and hold A LMB D Side Button 1 and E Side Button 2 together for 3 seconds.
The F Top Indicator LED will flash:

  • On – Green
  • Off – Red

Polling Rate

To change the Polling Rate, press A LMB B RMB and E Side Button 2 at the same time and hold for 3 seconds.
The K Dongle Indicator LED will flash:

  • 500 Hz – Red
  • 1000 Hz – Green
  • 2000 Hz – Blue
  • 4000 Hz – Orange

HIGROUND-V1-Wireless-Dongle-fig-9

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals