dji TX2202109 Action Camera User Guide
- June 5, 2024
- DJi
Table of Contents
DJI TX2202109 Action Camera
description
- Linking Status Indicator
- Link Button
- Firmware Update Port (USB-C)
Disclaimer and Warning
Congratulations on purchasing your new DJI OSMO”” product. Please read this
entire document and all safe and lawful practices DJI OSMO provided carefully
before use. Failure to read and follow instructions and warnings may result in
serious injury to yourself or others, damage to your DJI OSMO product, or
damage to other objects in the vicinity. By using this prduct, you hereby
signity that you have read this document carefully and that you understand and
agree to abide by all terms
and conditions of this document and all relevant documents of this product.
You agree to use this product only for purposes that are proper. You agree
that you are solely responsible for your own conduct while using this product,
and for any consequences thereof. DJI OSMO accepts no liability for damage,
injury or any legal responsibility incurred directly or indirectly from the
use of this product.RONIN is a trademark of SZ DJI OSMO TECHNOLOGY CO., LTD.
(abbreviated as “DJI OSMO”) and its affliated companies. Names of products,
brands, etc., appearing in this document are trademarkS or registered
trademarks of their respective owner companies. This product and document are
copyrighted by DJI OSMO with all rights reserved. No part of this product or
document shall be reproduced in any form without the prior written consent or
authorization of DJI COSMO.This document and all other collateral documents
are subject to change at the sole discretion of DJI OSMO. For up to date
product information, visit http://www.dji.
com and click on the product page for this product.
This document is available in various languages. In the event of divergence
among different versions, the English version shall prevail.
Introduction
When used with the ultra-bright remote monitor, the DJlI Ronin 4D Video Transmitter can be installed on the back panel of DJI Ronin 4D to transmit video and control
Usage
Installation
- Press the battery eject button and remove the Inteligent Battery.
- Remove the four M4x19 screws on the battery compartment and remove the battery compartment.
- Install the four antennas on the video transmitter.
- Install the video transmitter on Ronin 4D and tighten three M4x19 screws.
- Install the battery compartment on the video transmitter and tighten the two M4x19 Screws. Reinsert the Intelligent Battery into the battery compartment.
Linking
To start linking, hold the Link button on the video transmitter or go to
Settings on the ultra-bright main monitor, tap Video Transmission, and then
Pairing. The linking
status indicator blinks red and qreen alternately
When the linking is complete, the linking status indicator turns solid green
and the video transmitter can communicate with the ultra-bright remote
monitor.
Firmware Update
Use DJI Assistant 2 (Ronin Series) to update the firmware of the video transmitter.
- Power on the device and connect it to a computer with a USB-C cable
- Launch OJI Assistant 2 (Ronin Series) and log in with a OJI account.
- Select the device and click Rrmware Update on the left side of the screen.
- Select the firmware version.
- The firrrr,vare will be downloaded and updated automatically.
- The device will restart automatk;ally after the firmware update is complete.
Specifications
Local regulations in some countries prohibit the use of the 5.8 GHz and 5.2
GHz frequencies. In some countries, the 5.2 GHz frequency band is only allowed
for ndoor use.
Please refer to http://www.dji.com/service for
after-sales service for your product where applicable.
OJI OSMO shall mean SZ OJI OSMO TECHNOLOGY 00., LTD. and/or its affiliated
companies where applicable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>