InstallGear 4 Gauge Complete Amp Kit Amplifier Installation Wiring Wire-Complete Features/Instruction Manual

InstallGear 4 Gauge Complete Amp Kit Amplifier Installation Wiring Wire

Specifications

• DIMENSIONS : 8.7 x 7.4 x 2.9 inches
• WEIGHT : 2.84 pounds
• MODEL NUMBER: ‎ ‎IG4AKR
• BATTERIES: 1 CR2 required
• BRAND: InstallGear

Introduction

InstallGear is a well-known name in developing superior quality wiring products for audio systems. They manufacture a lot of audio products such as Speaker Wire, Power and Ground Control, Ring Terminals, Distribution Blocks, Rubber Grommets, and Amp kits. The InstallGear offers the perfect amplifier kit for installing a car amplifier with the right wires and parts. The amplifier is an important part of the car’s sound system and boosts the low- level audio signals from the source to enough gain so that they can be used to power the speakers. The gauge power is 17 ft long and made of soft PVC jacket with copper clad aluminum. The length of the gauge ground wire is about 3 feet and is also made of soft PVC jacket and copper-clad aluminum. The amplifier kit has 17 feet 2 channel RCA audio cables with easy polarity identification.

What’s in the box?

• 4 Gauge Power Wire
• 4 Gauge Ground Wire
• ANL Fuse Holder x 1
• RCA Audio Cable x 1
• Gauge Fork Terminals x 4
• Gauge Ring Terminals x 4
• 14 Gauge Speaker Wire
• Remote Wire
• Split Loom
• Rubber Grommet
• Wire Ties x 10

How to connect the Amp Kit?

1. Use the 14-gauge speaker wire to connect the speakers to the head unit.
2. Connect one fork terminal to the 18-gauge remote wire.
3. Connect this wire to the remote of the amplifier from the terminal end and the other side to the head unit.
4. Connect one fork terminal to the 4-gauge power wire and connect it to the battery of the amplifier.
5. On the other end of the 4-gauge power, a wire connects the ring terminal and connect it to the battery of the car.
6. Connect the Grommet, split loom and ANL fuse holder as shown in the picture.
7. Connect another fork terminal to the 4-gauge ground cable and then connect it to the ground of the amplifier.

8. Connect the other end of the ground cable to a ring connecter and then to chasis ground point.

FREQUENTLY ASKED QUESTIONS

• Is it good for a starter? 270watts two-channel? Just amp, a box with 2 8s
  Yes, it will be fine.

• Is this really a 4-gauge kit?
  It’s a heavy-duty 4-gauge kit.

• Will this be a good kit for my one 12-in-a-subwoofer?
  Yes, it will be fine for 12” subwoofer.

• Will the skid work on a 600 W Sony amplifier running to 12-inch subwoofers ?
  Yes, it has a 1000-watt amp and can push two 12” subs.

• Will this work for a 3000-watt system?
  Yes, it will work completely fine for a 3000-watt system.

• Will this work on a 2000watt boss amp powering 2 MTX 12” terminator subs?
  This will work as you are going for a 4-gauge wire.

• How long is the battery wire?
  The battery wire is almost a foot and a half.

• I have an 800-watt amp and is a 4 gauge a good size for my amp?
  Yes, 4-gauge size will be good for your amplifier.

• What gauge is the remote wire?
  The remote wire is 14 gauge.

• Is this copper or aluminum?
  The wires are copper.

• What is the split loom in this kit for specifically?
  The split loom is used to cover the red cable inside the engine compartment.

• Can I run these on a 2400-watt amp?
  Yes, you can these on a 2400-Watt Amplifier.

• Would this work with a Rockville DB13 3000 2 ohms with 2 Pioneer Shallow Mount 4ohm subs?
  Yes, this work fine with the Rockville DB13 3000.

• What tools will I need to install this with a subwoofer?
  In order to install this with a subwoofer, you will require the following tools:
  Drill
  Screw driver

• Volt meter
  Plier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>