eve CES 2022 Outdoor Camera Instruction Manual
- June 5, 2024
- eve
Table of Contents
Meet Eve Outdoor Cam
Get started
** If you are unsure or uncomfortable about installing Eve Outdoor Cam,
consult a qualified electrician. To be installed and/or used in accordance
with appropriate electrical codes and regulations.**
**View the installation video atwww.evehome.com/outdoorcam-
installation
Choose a location
Eve Outdoor Cam is best installed to replace an existing outdoor light. An
installation height of 2.5 m / 8 ft and a tilt angle of 30° is ideal, however,
you can easily adapt Eve Outdoor Cam to your needs thanks to the three-axis
camera angle adjustment.
Please respect local laws regarding the filming of public spaces.**
Check Wi-Fi coverage
Outdoor install locations often offer challenging conditions for Wi-Fi
reception. Before you proceed with the installation of Eve Outdoor Cam, ensure
that Wi-Fi coverage is sufficient at the desired location.
Eve Outdoor Cam connects exclusively to 2.4 GHz Wi-Fi networks for greater
range and reliability. To check coverage using your iPhone, make sure it is
connected to a 2.4 GHz Wi-Fi network. You may need to temporarily disable the
5 GHz network of your router.
Hold your iPhone close to the wall at the location you want to install Eve
Outdoor Cam. Wait for at least 10 seconds and check the Wi-Fi signal on your
iPhone. You should have at least two bars of reception.
If your Wi-Fi signal does not reach the desired location, you may try to move
your Wi-Fi access point closer, use a Wi-Fi repeater or an additional mesh
node, or choose a different location for Eve Outdoor Cam.
Disconnect power
CAUTION – Risk of electric shock!
In your fuse box, switch off the fuse connected to your existing outdoor
light. Switch the associated light switch on and off to make sure that there
is no current flowing.
Installation
-
Install the Mounting Plate
Disassemble and remove your existing outdoor light. Position the mounting plate (1) and remove one of the plastic clips to create an opening for passing the power cable through. Ensure the UP arrow is pointing upwards and trace the screw holes. Remove the mounting plate (1), drill into your tracings, and insert the supplied wall anchors.
Eve Outdoor Cam requires both a neutral wire and a connection to a ground wire. If these are not present, Eve Outdoor Cam is not compatible with this location.
You
may also use the wall anchors from your existing outdoor light if they’re
spaced as required. In this case, please ensure that the UP arrow is pointed
upwards, or horizontally to the left or right.
Place the mounting bracket (2) on top of the mounting plate (1) and secure them using the supplied screws.
-
Mount Eve Outdoor Cam
Place the mounting cover (3) on top of the mounting bracket (2) with the cable inlet at the top.
Place the
mounting ring (4) with the moisture outlet facing downwards and secure it by
twisting it to the left.
Place the
mounting clip (5) along with the metal bracket in the recessed area of the
mounting cover (3) and snap in the mounting clip (5). Turn the supplied
mounting screw (6) clockwise to attach Eve’s, Outdoor Cam.
Please ensure you keep holding Eve’s Outdoor Cam until the screw is sufficiently fastened. You don’t need to fasten the screw all the way, and don’t need to use the supplied Allen key just yet – simply use your fingers.
-
Connect Eve Outdoor Cam
Pass the cable through the cable inlet.
Turn Eve
Outdoor Cam upside down and open the mounting ring (5) again by twisting it to
the right and pulling it towards you for easy access to the cabling.
Pass the
cable of Eve Outdoor Cam through the wall mount so that the ingress seal sits
flush with the mounting cover (3).
Secure
the ingress seal (8) with the ingress seal bracket (7).
Connect
the corresponding wires from your power cable to Eve Outdoor Cam using the
supplied connection terminals.
Eve
Outdoor Cam requires both a neutral wire and a connection to a ground wire.
If these are not present, Eve Outdoor Cam is not compatible with this location.
Turn Eve Outdoor Cam back to the original position and stow the terminals and cables in the wall mount.
-
Set up Eve Outdoor Cam
Align Eve Outdoor Cam and fully secure it using the supplied Allen screw.
Switch
the fuse in your fuse box back on.
The status LED should now turn on.
Download the Eve app from the App Store.
Open the Eve app and tap Add Accessories. Eve will now guide you through the setup process.
If you have already set up another accessory, go to the Eve settings to add Eve Outdoor Cam to your home.
To
add Eve Outdoor Cam, use the HomeKit code on the back of this manual.
Enjoy
Recordings
Eve Outdoor Cam exclusively supports Apple HomeKit Secure Video, enabling you
to securely store activity detected by Eve Outdoor Cam in iCloud. HomeKit
Secure Video requires iCloud+ (not included). iCloud+ with 50 GB storage
supports one camera, iCloud+ with 200 GB storage supports up to five cameras,
and iCloud+ with 2 TB storage supports an unlimited number of cameras. Camera
recordings don’t count against your iCloud+ storage limit. Recordings are
saved for ten days and then deleted automatically. If you want to hold on to a
recording, you have the option to save it permanently.
Securely access Eve Outdoor Cam while you’re away from home and intelligently
determine when a person, animal, or vehicle is in the video recorded by Eve
Outdoor Cam.
Any Apple TV HD, Apple TV 4Kor HomePod using the same iCloud account as your
iPhone will automatically serve as a home hub, no further setup required.
To adjust the settings of Eve Outdoor Cam, tap the Settings icon in the video
feed of the Home app on your iPhone or iPad.
Access
To invite people with an iCloud account to access Eve Outdoor Cam, select Home
Settings in the home app. Only the owner of the home in the Home app can
change the streaming and recording mode when home or away and determine if
others can view recordings of Eve Outdoor Cam.
Status
You can turn off the camera status light in the Eve Outdoor Cam settings in
the Home app.
Off – Streaming / Recording disabled
Blue – Streaming enabled and inactive
Red – Streaming active / Recording enabled
Eve Outdoor Cam is designed to safeguard your personal data. Video streamed
from Eve Outdoor Cam and iCloud is end-to-end encrypted to your devices, so
only you and the people you share your Apple Home app with can view it.
Learn more at evehome.com/privacy
Motion Detection
Thanks to a dedicated motion sensor, Eve Outdoor Cam will not bother you with
reacting to leaves blowing in the wind, small animals, and other events that
do not require your attention.
You can adjust the motion sensitivity in the accessory settings in the Eve
app.
Motion Light
Eve Outdoor Cam will automatically turn on the floodlight when motion is
detected by the dedicated motion sensor. To limit the automatic motion light
to nighttime, adjust the duration, or deactivate it together, access the
accessory settings in the Eve app.
Light Boost
If you want the integrated floodlight to shine extra-bright, tap the light
boost button in the Eve app. You can also enable a light boost for the
automatic motion light. Light boost will turn off automatically after a period
of time.
Reset
Wi-Fi Reset
To connect Eve Outdoor Cam to a different Wi-Fi network, push and hold the
reset button on the bottom of the camera with a paper clip for 5 seconds until
the LED starts blinking blue. Release the reset button as soon as the LED
starts blinking blue and open the Home app to add Eve Outdoor Cam to the Wi-Fi
network your iPhone is currently connected to.
Reset
To reset all settings of Eve Outdoor Cam, including the HomeKit pairing, push
and hold the reset button on the bottom of the camera with a paper clip for 10
seconds until the LED starts blinking red.
Legal Information
This device complies with part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, you
are encouraged to try to correct the interference by one or more of the
following measures: reorient or relocate the receiving antenna; increase the
separation between the equipment and receiver; consult the dealer or an
experienced radio/TV technician for help. ·
This Class B digital apparatus complies with Canadian ICES-003. Changes or
modifications not expressly approved by Eve Systems could void your authority
to operate this device. This equipment complies with FCC RF, IC RSS-102, and
CE radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For questions about compliance with FCC regulations, please contact:
Compliance Officer, Eve Systems, 100 Pine St., Suite 1250, San Francisco CA
94111, USA · UK
Authorized Representative: Authorised Representative Service, The Old
Methodist Chapel, Great Hucklow, SK17 8RG, UK Hereby, Eve Systems declares
that this device is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EC.
The declaration of conformity is available at
www.evehome.com/doc
Purpose of control: operating control; construction of control: plug-in
operating control; type 1 action, operating time: continuous; temperature
range: -20 °C – 45 °C; frequency range: 2412 – 2472 MHz (2462 for FCC, ISED),
max. EIRP: 20 dBm
Product: 10ECA4101/ 10ECA8101· Model: 20ECA8101 / 20ECA4101
Part: 51ECA9901· FCC ID: SNE-ODC-001 · IC: 11192A-ODC001
Eve Systems GmbH, Rotkreuzplatz 1, 80634 Munich, Germany
Please keep your HomeKit Setup Code in a safe place.
You need it to securely add Eve to your home, and nobody but you has a
copy.
Documents / Resources
| eve
CES 2022 Outdoor
Camera
[pdf] Instruction Manual
CES 2022, Outdoor Camera, CES 2022 Outdoor Camera
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>