EAZYRC EAZ11807 Glacier 1/18 RTR Scale Mini Crawler Instruction Manual

: June 5, 2024
: EAZYRC

Table of Contents

EAZYRC EAZ11807 Glacier 1/18 RTR Scale Mini Crawler
Function
Install the Batteries
FCC STATEMENT
Introduction
Setting the Gear Mesh
Charging the Battery
Lithium Polymer (LiPo) Battery Warning
Spare parts list
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EAZYRC EAZ11807 Glacier 1/18 RTR Scale Mini Crawler

EAZYRC-EAZ11807-Glacier--RTR-Scale-Mini-Crawler-
product

Function

Push the trigger forward to slow down or break.
Pull the trigger back to accelerate

Install the Batteries

Remove the battery compartment cover.
Replace the used batteries with new AA-size batteries.

Please replace batteries when the power indicator blinks or the buzzer beeps EAZYRC-EAZ11807-Glacier--RTR-Scale-Mini-Crawler-fig-2

Keep the transmitter and receiver ill 40cm apart when operating.

Throttle trim: If the vehicle inches forward or backward without throttle input, adjust the trim to set the neutral throttle position.
Steering trim: If the vehicle veers left or right without any steering input, use the steering trim to adjust the steering servo until the vehicle tracks straight

Operating procedure

Always tum the transmitter on before turning on the vehicle.
Always disconnect the vehicle BEFORE turning off the transmitter.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. FCC ID: 2AUBX –TX01Z

Introduction

18 GLACIER, a new masterpiece from EAZYRC comes to rock you with shocking momentum!
Pickup trucks, being the symbol of post-modern US western culture, are born with ruggedness and conquest,from which EAZYRC boldly brought in for the first time to develop a brand new model-That is 1:18 Glacier.
The Glacier features hard and strong body lines offering a great taste of American vintage, bringing you right back to American 70s at once with a glance of the square-shaped front end. The bold design renders the characteristics of grandeur and Vividness with the exquisite body head and tail design. Customized license stickers are available for players to decorate the front and rear of this car model.
Metallic luster has been in full display when the electrostatic spray is deployed on the vehicle, making the craftsmanship and visual presentation up to the level of the real car.
The body adopts the typical design of pickup truck, meaning you can access to large space of the bucket carrying different items and an openable bucket rear door panel. Great fun and authenticity are well enhanced no matter for static set-up or dynamic walking.
In terms of frame suspension, the bearing angle of the rear spring suspension is adjusted according to the truck model to achieve a longer and smoother driving journey.
Move your attention to the hood design, as always, EAZYRC provides an openable hood and enough engine compartment space for players to DIY based on their interests, such as increasing the counterweight for better driving posture, or replacing the larger-capacity battery to improve the endurance, etc
The interior is realistically drawn, and the dashboard and steering wheel are restored according to the original scale. In the simulation of one-seat replica history, all parts are precision injection molded in one piece.
Cool lights, simulating the real car light set, including headlights, turn signals and reversing lights.
Newly equipped with newly developed high-performance retro wheels and all-terrain tires, grip is substantially improved.
Glacier storm skin is a comprehensive entertainment and RC remote control model car, to the hand that is to play, to achieve at any time and anywhere as you like climbing, crossing.

Warnings

When not in use, must be remove the battery of the remote control and vehicle.

This vehicle is not intended for those under 14 years of age without proper adult supervision. It is not a toy!
Failure to operate or maintain this vehicle in a safe manner can result in bodily harm.
Replace damaged components with original factory-parts. Pay special attention to the polarity of all vehicle wiring.
This product is strictly forbidden to be used in water, please do not drive on water stains
Only use approved 2 cell lithium polymer batteries. Do not over-charge or over dis-charge the battery as doing so may cause the battery to become a fire hazard. If the battery should become hot during charging, discontinue charging immediately and disconnect the battery from the charger. Never leave the battery unattended while charging. If you are unsure of how to charge this battery, please seek the advice of experienced RC users. Never let children charge the battery without adult supervision.
The motor will become hot during use. Allow 10-15 minutes between runs for the vehicle to cool down. Doing so will prolong the life of your vehicle.
Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water or unstable terrain. The operator is solely responsible for their actions.
The product is composed of precision electrical components. It is critical to keep the product away from moisture and other contaminants. If exposed to a humid environment, make sure the electronics are fully dried prior to using them again.
Always check the radio range of the vehicle prior to operation in order to prevent radio loss or interference. Operate this product within your ability. If the vehicle is dangerous to retrieve, it’s never worth the risk.
Always turn on the transmitter before connecting the battery on the model. When turning off the model, always disconnect the battery first, and then tum off the model, always disconnect the battery first, and then turn off the transmitter. If this order is reversed, the model may become uncontrollable and cause serious damage.
Never allow transmitter batteries to run low as it may cause loss of vehicle control.
Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold climate. Do not store the model near any source of heat such as oven or heater. Store the model indoors, in a climate-controlled, room temperature environment.
Never shorten the receiver antenna; this may affect the transmitting range of the radio system.

Setting the Gear Mesh

The gear mesh is the clearance between the pinion and spur gears in your vehicle. If the motor or gearing components are replaced, check that the gears are not meshing too tightly as this may cause premature wear.

Charging the Battery

Connect the charger to a USB port then connect the battery to the charger.
When charging. the Green LED is flash, when charged, the Green LED is stable.
Do not let the battery charge unattended!
if the battery or charger is hot, disconnect the battery and charger immediately as this may be caused by an internal short-circuit.

Lithium Polymer (LiPo) Battery Warning

Never charge a lithium polymer battery with a charger designed for Nied, NIMH, or any other type of battery chemistry.Use ONLY charger designed for Li Po battery.
Do not leave LiPo battery unattended during charging.
Do not overcharge the battery.
Always charge LiPo batteries on non-flammable, heat-resistant surfaces.
Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat at any time.Cells that reach greater than 140 Fahrenheit(60°C) will usually become damaged and will catch fire.
Do not charge the LiPo pack while it is still in the model. Never charge or store battery packs in a vehicle.
Do not discharge LiPo; doing so will damage the battery.
Do not expose LiPo cells to water or moisture at any time.
Do not store battery near open flame or heater.
Do not assemble LiPo cells or pre-assembled packs together with other LiPo cells or packs.
Always store LiPo batteries in a secure location away from children.
Always remove the LiPo battery if the model is involved in any kind of crash.
Carefully inspect the battery and connectors for even the smallest damage.
CAUTION: Cells may become hot after usage. Allow the pack to cool to room temperature prior to recharging.
Do not allow the electrolyte to get into the eyes or on the skin. Wash affected areas immediately if they come into contact with electrolytes. Do not alter or modify connectors or wires of a LiPo battery pack.
Always inspect the condition of the battery before charging and operating.
Do not short circuit the LiPo battery.
Do not have contact with a leaky/damaged battery directly.
Do not charge the battery out of recommended temperature range(0°C-45°C).

NOTE

If it is not in use for a long time, unplug and take oﬀ the battery to prevent battery leakage.
Do not open, disassemble, or attempt to repair the battery.
Please disconnect the battery from the receiver before charging.

Spare parts list

E1070 EAZY GLACIER Hood BLUE
E1071 EAZY GLACIER Front and Rear Light Cup Set
E1072 EAZY GLACIER Hood Mount Set
E1073 EAZY GLACIER Rearview Mirror And Wiper
E1074 EAZY GLACIER Bumper And Side Panel
E1075 EAZY GLACIER Lens
E1076 EAZY GLACIER Body SHELL
E1077 EAZY GLACIER CHASSIS
E1078 EAZY GLACIER HANDLE
E1011 EAZY Teraz Tire 19.2 x 13.5 x 56
E1012 Eight Planets Style Wheels plastic parts
E1014 EAZY LIPO Battery 2S LIPO 380mAh
E1016 EAZY USB Charger
E1019 EAZY 050 Motor set
E1020 EAZY Gear set
E1079 EAZY Transmission Shaft full set GLACIER version
E1067 EAZY SCREW SET
E1023 EAZY 5 wire 9g SERVO
E1080 EAZY GLACIER Window
E1036 EAZY 1:18 Rear wheel shaft
E1037 EAZY 1:18 Wheel Hex
E1038 EAZY 1:18 Rear axle plastic parts
E1040 EAZY 1:18 SHOCK PLASTIC PARTS
E1041 EAZY Connecting Rod
E1042 EAZY 1:18 M4 ALLY BALL
E1043 EAZY 1:18 BALL HEAD
E1044 EAZY 1:18 C HUB PARTS
E1045 EAZY 1:18 FRONT/REAR AXLE parts
E1046 EAZY 1:18 SERVO HORN
E1081 EAZY GLACIER MIRROR LENS
E1048 EAZY 1:18 FRONT OUTDRIVE SHAFT
E1049 EAZY 1:18 Gear Box Plastic Parts

Declaration of Conformity (DoC)

declare under our responsibility that the product: Type of Equipment: Patriot Driving System & 2.4GHz Control System Brand Name: EAZYRC
Equipment Model: 11807

to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the RED Directive 2014/53/EU, EMC Directive 2014/30/EU,FCC Identifier 2AUBX-TX01Z, and EU RoHS Directive 2011/65/EU. The product is in conformity with the following standards and/or other normative documents:

ETSI EN 301 489-1 V2.2.3 (2019)
ETSI EN 301 489-17 V3.2.4 (2020-09) EN 55032:2015
EN 55035:2017
EN 61000-3-2:2014.
EN 61000-3-3:2013
IEC/EN62368-1
EN 62368-1:2014+A11:2017 EN 62479:2010
EN 300 328 V2.2.2:2019-07

DISTRIBUTOR

North America: AMain Distributing 424 Otterson Drive Chico, CA 95928 https://www.amaindistributing.com/ 530-894-9082

The United Kingdom