VonHaus 3500183 2200W 9″ Angle Grinder Instruction Manual
- June 5, 2024
- vonhaus
Table of Contents
VonHaus 3500183 2200W 9″ Angle Grinder
- Please read all instructions carefully before use and retain for future reference.
- Protect your eyes.
- CAUTION Sharp edges.
- Protective clothing must be worn
- Protect your hands.
- Wear suitable footwear
- Do not use outdoors.
- CAUTION Do not immerse in water.
INTENDED USE
Only operate the power tool/machine for its intended purpose and within the parameters specified in this manual. This power tool/machine is for domestic use only. Do not use outdoors or on wet surfaces. This power tool/machine is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless supervised or given appropriate instruction concerning the product’s use by a person responsible for their safety.
GENERAL PRECAUTION
Do not allow it to be used as a toy. Children should be supervised to ensure they do not play with the power tool/machine. If the power tool/machine is not functioning properly, has been dropped, damaged, left outdoors, or immersed in liquid, do not use, contact DOMU Brands Customer Services. Do not use the power tool/machine if any parts appear to be faulty, missing, or damaged. Ensure all parts are securely attached before use.
RISK OF PERSONAL INJURY
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Prevent unintentional starting. Ensure the switch is in the off position before connecting to the power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch, or energizing power tools that are switched on, invites accidents. Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, or gases or dust. Power tools create sparks that may ignite dust or fumes. Always wear eye protection. Any power tool can throw foreign objects into your eyes and cause permanent eye damage. Always wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1 Every day glasses have only impact-resistant lenses. Do not expose power tools to rain or wet conditions. Water entering the power tools will increase the risk of electric shock. Stay alert, watch what you are doing, and use common sense when operating a power tool/machine.
Do not use a power tool/machine while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tool/machine may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying a power tool/machine with your finger ontheswitch or energizing power tool/machine that have the switch on invites accidents. Remove any adjusting key or spanner before turning the power tool/machine on. A spanner or a key left attached to a rotating part of the power tool/machine may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool/machine in unexpected situations. Dress appropriately. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
WORK AREA SAFETY
Keep the work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tool/machines in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools/machines create sparks that may ignite thedust or fumes. Keep children and bystanders away while operating a power tool/machine. Distractions can cause you to lose control.
GENERAL POWER TOOL USE AND CARE
Do not force the power tool/machine. Use the correct power tool/machine for your application. The correct power tool/machine will do the job better and safer at the rate for which it was designed. Do not use the power tool/machine if the switch does not turn it on and off. Any power tool/machine that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool/machine before making any adjustments, changing accessories, or storing power tool/machine tools. Such preventive safety measures reduce the risk of starting the power tool/machine accidentally. Store idle power tool/machine out of the reach of children and do not allow persons unfamiliar with the power tool/machine or these instructions to operate the power tool/machine. Power tools/machines are dangerous in the hands of untrained users. Maintain power tool/machines. Check for misalignmentor binding of moving parts, breakage of parts, and any other condition that may affect the power tool/machine’s operation. If damaged, have the power tool/machines repaired before use. Many accidents are caused by poorly maintained power tool/machines. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool/machine accessories and tool bits in accordance with these instructions, take into account theworking conditions and the work to be performed. Use of the power tool/machine for operations different from those intended could result in a hazardous situation.
CLEANING & MAINTENANCE
Never soak or immerse electrical components and or a component that has a plug attached. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing. Such preventive safety measures reduce the risk of starting the power tool accidentally. Ensure the motor has fully stopped before cleaning, clearing a blockage, checking, or carrying out any maintenance on the tool. Maintain your power tool. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired by a qualified repair person before use. Many accidents are caused by poorly maintained power tools.Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Regularly check external nuts and fixings to ensure vibration caused by normal use has not begun to loosen them. Store idle power tools out of reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the Breaker. Locate the power tool out of reach of children, in a dry, locked unit. Make sure that the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. Remove the plug from the main socket/battery (where applicable) before carrying out any adjustment or maintenance. Always store the power tool/machine in a dry place.If the power cord is damaged, it must be replaced by a qualified service technician. Keep the ventilation slots and motor housing as free of dirt and dust as possible (where applicable). Clean the power tool/machine by rubbing it with a clean cloth and blowing it clean using low-pressure compressed air is recommended. Ensure you have all the pieces listed. If you are missing any components, contact our customer services department at hello@domu.co.uk (UK/EU) usasupport@domubrands.com (US). DO NOT proceed with assembly if any components are missing.
ANGLE GRINDER
Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite dust or fumes. Keep bystanders, children, and animals away while operating the power tool. Distractions can cause you to lose control. Dress appropriately. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts to prevent them from becoming caught in the tool. Remove any adjusting key or wrench before turning the power tool on. A wrench or key left attached to a rotating part of the power tool may result in personal injury. If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used to reduce dust-related hazards. Use clamps, or another practical way, to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control. Make sure that there are no nails or foreign objects in the path of the workpiece to be cut or sanded. Be aware of hidden hazards. Before cutting into walls, floors or ceilings, check for the location of wiring and pipes. Prevent unintentional starting. Ensure the switch is in the off position before connecting to the power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch, or energizing power tools that are switched on, invites accidents.
WARNING! Only use accessories recommended for use with this Grinder. Follow the instructions that accompany the accessories. The use of improper accessories may result in injury to the operator or damage to the tool. Do not use the power tool if the switch does not turn it on and off. A power tool that cannot be controlled with the switch is dangerous and must be repaired. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool whilst tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a power tool may result in serious personal injury. Hold the power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord. A cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Keep hands away from the cutting area. Never reach underneath the workpiece for any reason.
Do not insert fingers or thumb into the vicinity of the blades/ sanding attachments. Do not stabilize the Angle Grinder by gripping the shoe. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate at which it was designed. Do not overreach. Keep proper footing and balance at alltimes. This will enable better control of the power tool in unexpected situations. Disconnect the plug from the power source and/or the battery back from the power tool before making any adjustments, changing accessories or storing. Such preventative safety measures reduce the risk of starting the power tool accidentally. The blade will continue to move after releasing the switch. Always switch the tool off and wait for the blade to come to a complete standstill before putting the tool down. Do not touch the workpiece or the blade immediately after operating the tool. They can become very hot.
TECHNICAL SPECIFICATION
- Rated Voltage 230V ~
- Rated Power 2200W
- Rated Frequency 50Hz
COMPONENT LIST
- Shoe
- Spindle Lock
- Handle Thread
- On/Off Switch
- Angle Adjustment
- Power Cable
- Guard
- Outer Washer
- Diamond Disk
- Auxillary Handle
- Wrench
COMPONENTS
ASSEMBLY
HANDLE ROTATION
OPERATION
DISPOSAL INFORMATION
Please recycle where facilities exist. Check with your local authority for
recycling advice.
CUSTOMER SERVICE
If you are having difficulty using this product and require support, please
contact hello@domu.co.uk (UK/EU)
usasupport@domubrands.com (US)
WARRANTY
To register your product and find out if you qualify for a free extended
warranty please go to www.vonhaus.com/warranty. Please retain a proof of
purchase receipt or statement as proof of the purchase date. The warranty only
applies if the product is used solely in the manner indicated in the warnings
page of this manual, and all other instructions have been followed accurately.
Any abuse of the product or the manner in which it is used will invalidate the
warranty. Returned goods will not be accepted unless re-packaged in its
original packaging and accompanied by a relevant and completed returns form.
This does not affect your stat-utory rights. No rights are given under this
warranty to a person acquiring the appliance second-hand or for com-mercial or
communal use.
COPYRIGHT All material in this instruction manual are copyrighted by DOMU
Brands.Any unauthorised use may violate worldwide copyright, trademark, and
other laws.
THANK YOU
Thank you for purchasing your product/appliance. Should you require further
assistance with your purchase, you can contact us at
hello@domu.co.uk (UK/EU)
usasupport@domubrands.com (US) VonHaus is
a registered trademark of DOMU Brands Ltd. Made in China for DOMU Brands. M24
2RW.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>