HOLMAN MK21013 7 Meter Misting Kit Instruction Manual
- June 5, 2024
- Holman
Table of Contents
HOLMAN MK21013 7 Meter Misting Kit
Outdoor Cooling Misting System
PLEASE READ THE INSTRUCTION MANUAL BEFORE USE
The Holman Misting system features 7mm diameter high-pressure tubing with
“compression fittings” that are made to match this tubing. The compression
fittings fit the pipe very precisely and simply push over the pipe and are
very easy to assemble. No clamps are required. Please note that your misting
system can be expanded with more Holman misting parts. These are available at
your Holman stockist.
The Way It Works
The misting system cools the air temperature by the evaporation of the fine
particles of water emitted by the misting nozzles. The process of evaporation
absorbs heat from the air and cools the area.
The misting nozzle emits very small amounts of water. It also breaks the water
into very small droplets or a “mist”. In hot conditions, the small water
droplets evaporate almost instantaneously. In cooler or humid conditions the
evaporation rate may be slower. Generally, you will not want to run the
misting systems continuously. If you do, the general environment may become
damp and unpleasant. The simple way to solve this problem is to use a Holman
Misting Timer. This timer can be programmed to suit the environmental
conditions of the day. You can easily adjust the “ON” time (in seconds) and
the “OFF” time (in seconds or minutes) and the misting system will
automatically turn on and off as you desire.
Glossary
PACKAGE CONTENTS
- 7m Misting Hose
- 6x Misting Tees with Brass Nozzles
- 1x Misting Elbow with Brass Nozzle
- 1x Misting Tee
- 1x Universal Tap Adaptor
- 2x Brass Misting Nozzles (Spare)
- 1x Misting Filter
- 2x Hose Joiners
- 1x Tee Joiner
- 1x Elbow Joiner
- 1x Auto Drain Valve
- 15x Hose Clamps
Misting System Assembly & Installation
Plan Your Misting Installation
Take 5 minutes to work out how you will run the misting pipe-work and where
you should position the misting jets, where your water source will come from
and where the supply pipeline will run.
The general idea is to position the jets to create a “mist curtain”
surrounding your outdoor entertainment area. It is best to position the jets
away from tables and chairs, and where people may sit as the jets may at times
drip water. You do need to work out what you can attach the pipe-work to and
plan a route that makes attaching the pipe-work easy
Water Supply
The misting system uses very little water volume. Each jet uses 2 litres an
hour. The misting system works best when you have a high pressure water
supply. The higher the pressure the finer the water droplet and the quicker
and more effectively the droplet evaporates and cools the area. A normal
household water supply is usually at an adequate pressure. The misting pipe
can be connected directly to a garden tap. Only fresh tap water is suggested
as bore or dam water may contain sediment that will block the jets. You can
use a garden hose to bring water from a tap in the area to the start of the
misting pipe-work. If the hose is running in the sun, please ensure it is a
good quality hose that will be able to withstand the pressure when the water
and hose may get heated. (See page 6 for Garden Hose connection)
HINT: If you want to easily maintain the use of the garden tap for other uses, install a Holman 2 way or 4 way manifold and fit the misting system to one outlet.
Positioning Misting Jets
- Spacing of jets.
- Location of jets over tables or chairs.
- How many jets in a particular area.
There are no fixed rules to how you position the jets. The more jets you have, the more water you will use and potentially the cooler the space will become. However, too much water can be a problem because the air can become saturated and even wet the people and objects in the space. Holman recommends the following:
- Space jets between 600mm and 1 meter apart.
- Locate jets away from tables and sitting areas if possible.
- Try and create a curtain of mist at least on two sides of the area being cooled.
- Install a Holman misting timer. This will allow you to regulate the amount of water entering a space by adjusting the “ON” times and “OFF” times of the timer. You would have more “ON” time on a hot dry day than a cooler moister day.
The HOLMAN misting timer allows you to make these settings in seconds, where other timers may not have this feature.
Installing The Fittings
The Holman Misting System features “compression fittings”. These fittings
feature a compression ring that grips the tube and prevents it from coming
loose or leaking water. The higher the pressure the better the compression
fittings hold onto the tube. To ensure a good joint, the tube must be cut
“square” and “burr-free”. The best way to achieve this result is to use the
Holman misting tube cutter. This ensures a clean square cut. It is also very
quick to use. (Holman Misting Tube Cutter sold separately – Product Code:
MS20011) Once the tube is cut the compression fitting is very simply
installed.
- Bring the 2 parts together, level and straight.
- Push the tube in while twisting the fitting a little.
- The tube should enter the fitting at least 10mm. Once tubing is installed it cannot be removed from the elbow, tee or joiner.
Installing The Misting System
Each section of tube should be connected before attempting to pin the system
to walls or beams. Start at the garden tap or water source point. If you are
using a Garden Hose (A), it is recommended that you install a Sprinkler
Adaptor (C) into the Misting Filter (8) as shown. Run the tube to the position
you want your first misting jet in. Use Tees or Elbows to go around corners or
split the pipe runs. Visit
www.holmanindustries.com.au for more info
on our sprinkler adaptors
Curtain of Mist for most effective coverage.
(Illustration shows 5 Misting Tees and 1 Misting Elbow being used as an
example of a basic layout. Further products to extend your misting system are
available at your local HOLMAN stockist).
Work out the spacing of the misting jets and cut the misting hose to length
and install the relevant misting tees. Finish each line with a misting elbow.
(3 x Misting Elbows are included in this System to enable installation of a
single or multiple line misting solution. More Misting Elbows are available at
your nearest HOLMAN stockist Product Code: MS20003) Use the hose clamps to
attach the misting hose to the wall or beams.
The Holman hose clamps use a very strong masonry nail that should not bend when you hammer it into timber or masonry.
- HINT 1: Run pipework along mortar joints in brickwork. Hammer the hose clamps into the brickwork for a reliable result.
- HINT 2: Use a hose clamp on each side of a misting tee to ensure the tee is firmly positioned and misting in the correct direction.
- HINT 3: If hammering into metal, the correct nails will need to be purchased.
- HINT 4: Avoid installing the tube in direct sunlight as this may cause the tube to go brittle over time.
Flushing The System
Perhaps the most important part of the installation process is to properly
flush the system. Remove ALL JETS and then connect the water and run for 4 or
5 minutes. This will ensure that all dirt and pipe swarf is flushed from the
system. If this is not done, the brass jets will clog up and then they will
not work correctly.The hole size in the brass jets is extremely small. It is
like this to ensure that the water particle is very small – like a mist.
Water Filter
Because the principle of evaporative cooling relies on very small volumes of
water evaporating and absorbing the ambient heat, it is critical that the
water entering the misting system is very clean and free of all particles that
will not pass through the very small hole in the misting jet. It is highly
recommended that the filter be installed immediately after the connection to
the water source. From time to time it may be necessary to clean the filter.
This is best done by using cleaning solution like vinegar. This is available
at your hardware store. This will not only assist clean solid particles away,
but it will dissolve calcium and iron deposits that build up as water
evaporates in the filter (and jets).
Auto Drain Valve
This is a very important component in your misting system. This should be
installed at a low point in the system. This valve will automatically release
the pressure in the line and them “dump” the water in the misting hose “above”
the level of the auto drain valve when the water is turned off. It is
important to note that the Auto Drain Valve should be positioned where water
can run freely. ie. Into a drain or garden area. This is important to stop the
misting jets from “dripping” and “dribbling” and also stops the build up in
precipitated salts (like calcium and iron) from the water. Do not remove the
end of Auto Drain Valve unless blocked. There is a very small ball inside and
if opened the ball will fall out.
Maintenance Of Your Misting System
Please use these hints to keep your misting system operational and prevent unnecessary clogging of the misting jets: –
-
Drain Water from your System
When your system is not in use, drain all water from your system. If you use an automatic draining valve, this job will happen automatically. -
Clean Nozzles
Periodically clean all nozzles by soaking them in a solution of vinegar, or similar calcium and iron remover. -
Flush System
Periodically remove all nozzles and flush the system by running water through it for 4 or 5 minutes. -
Clean Filter
Periodically clean the filter by soaking in a solution of vinegar to remove calcium and iron buildup.
Troubleshooting
- Clean Nozzles
If nozzles are “dripping” or not “misting” properly, they must be removed and soaked in a cleaning solution like vinegar. If this fails to clean the jet, it is highly recommended to purchase replacement jets and replace all jets as required.
We really appreciate having you as a customer and would like to say thank
you for choosing us.
We recommend registering your new product on our website. This will ensure we
have a copy of your purchase and activate an extended warranty. Keep up to
date to with relevant product information and special offers available through
our newsletter. www.holmanindustries.com.au/product-
registration/
References
- Holman Industries - Irrigation, Garden Lights, Plumbing
- Product Registration and Extended Warranty - Holman Industries
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>