Slotva 1500000355429 Multi Texture Reverb Instruction Manual
- June 5, 2024
- Slotva
Table of Contents
1500000355429 Multi Texture Reverb
9 volt DC, Center Neg. 100ma min*
Output Jack Input Jack
Mode Switch Secondary Function: Wave shape selection
Depth knob Secondary Function: Modulation Rate
The Slötvå Multi Texture Reverb allows players to create and save up to three
presets with lush, modulated, sleepy and ambient soundscapes. Stocked with
three different algorithms specifically designed to invoke textures for
bringing dreams from your subconscious to reality.
The toggle switch allows three different reverb modes, Dark (Lower Octave),
Rise (Ambient Swell) and Dream (Latching Pad), while secondary functions on
the switch change between different wave shapes for the modulation on the
reverb trail.
Combine deep modulation with long washy trails and experience, the Slö.
Bypass LED
Bypass Switch/ Secondary Function
Sustain Switch
*The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended.
Got questions or need a repair? help@walrusaudio.com. All our pedals come with
a limited lifetime warranty.
CONTROLS: DECAY Adjusts the length of the reverb decay. Go from tight short
reverb, at full counter-clockwise, to long drawn out texture at full
clockwise.
FILTER Controls the tone of the reverb decay. Each algorithm includes a low-
pass filter optimized for that unique sound and the knob controls the filter
cutoff frequency. Turn the knob up to open the filter for brighter tones, and
down to close the filter resulting in a darker tone.
MIX Turn counter-clockwise for increased dry signal, and clockwise for more
reverb. Use the white line to reference approximately equal parts dry and
reverb. Since this point is around 2 o’clock, it gives a greater range of
adjustment of your mix ratio below the 50/50 point making it easier to dial in
the perfect amount of reverb.
X The X knob changes jobs depending on which algorithm is selected.
DARK Sets the level of a -1 octave signal that feeds the reverb.
RISE Sets the amount of time it takes the reverb to swell in after a note is
played. Set lower for shorter rise times and higher for longer rise times.
DREAM Sets the depth of vibrato applied to the reverb decay.
DEPTH Controls the amount of modulation applied to the reverb decay. Go from
no modulation, to nightmare inducing pitch bending at high settings. Secondary
Function: Rate – Controls the speed of the modulation applied to the reverb
decay.
ALGORITHM SWITCH The toggle switch selects one of three onboard reverb
algorithms. Secondary Function: Wave Shape selection.
REVERB MODES: Use the toggle switch to select one of three onboard algorithms.
DARK Add a lower octave to your reverb trail. Create deep and wide
atmospheric sounds and channel nightmarish soundscapes. X knob sets the level
of a -1 octave signal that feeds the reverb.
RISE Auto-swell reverb for beautiful cinematic swells. Don’t rush it. Let it
breathe and gently wake up. X knob sets the amount of time it takes the reverb
to swell in after a note is played. Set lower for shorter rise times and
higher for longer rise times. Note: Rise works best in front of an amp, not
through an FX loop.
DREAM Lush reverb with a latching pad function. Press the sustain switch to
latch signal. Experiment with the X knob to add vibrato over the pad. Press
sustain again and pad will decrescendo according to where decay knob is set. X
knob sets the depth of vibrato applied to the reverb trail.
MODULATION WAVE SHAPES:
SINE Smooth and even pitch up and down modulation. WARP Asymmetric pitch
up modulation similar to a warped record. SINK Asymmetric pitch down
modulation for sinking detune similar to a Bigsby.
BYPASS Turns the effect on and off. It also features our smart bypass
switching. When the switch is in off position, press and hold to temporarily
activate the effect to add a moment of reverb texture. Releasing the switch
turns the effect off, and fades it out.
SUSTAIN When pressed, the decay switch ramps up the reverb trail to maximum
creating long dreamy reverb trail and then ramps back down to the decay knob
setting when released. In the “Dream” algorithm, the sustain switch is
latching. Press it once to capture and sustain the current reverb decay for
extremely long pad-like sounds. Press it again to let the reverb trail taper
off, based on the position of the decay knob.
SECONDARY FUNCTIONS To access the secondary functions, with the pedal
engaged, hold down the bypass switch and use the toggle to select the desired
wave shape, and the depth knob to set the desired rate. The bypass LED will
flash at the rate of modulation while in the secondary mode. The pedal
remembers the wave shape and rate settings for the current preset when saved,
until the next time they are modified. The pedal also maintains the algorithm
and depth setting when modifying secondary functions.
TRAILS MODE The Slö can run in trails or no trails mode. In trails mode,
when you turn the pedal off, the reverb decay dies off naturally. In no trails
mode, the decay is abruptly cut off when you turn the pedal off. To toggle
between either mode, hold down the bypass switch for 1 second while applying
power to the pedal. Unplug power and repeat to toggle to the other mode.
Default is Trails mode.
Presets – Slotva has 3 on-board presets (Red, Green, Blue). If the same
algorithm is used in the next preset, the reverb sound will fade into the
saved settings.
Scroll through the presets by pressing both stomp switches at the same time.
Each press of both stomp switches will load the next preset until you get back
to red and the pattern of Red, Green, Blue repeats.
To save a preset: 1. Scroll to the preset color you want to save a new sound.
2. Using the knobs and switches, dial in the desired reverb sound. The preset
LED will turn purple indicating the preset has been modified. The preset LED
will go back to the preset color when you cross the current saved setting. 3.
To save, hold down the Bypass and Tap switches until the preset LED blinks.
The preset is now saved and the LED will return to the preset color.
FACTORY RESET To perform a factory reset, hold down both foot switches while
plugging in power to the pedal. Hold both switches until the Preset LED starts
to flash, then release both switches. The pedal will now be in Trails mode
with the three default presets loaded in the Red, Green and Blue presets. The
default wave shape are as follows: Dark – Sink // Rise – Sine // Dream – Sink.
WALRUSAUDIO.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>