cache Trajecta Helmet User Manual
- June 17, 2024
- cache
Table of Contents
cache Trajecta Helmet
HELMET FEATURES
- Smartshock® Rotational Protective System (13 points)
- Incredibly light, full face enduro and all-mountain helmet
- Multi-density EPS foam injection molded with polycarbonate in two size-specific molds (SM, MD and LG, XL)
- Patent-pending chin bar integration
- Massive airflow with a class-leading 24 ventilation ports
- Multi-point adjustable visor designed for maximum vision and goggle stowage
- Washable, moisture-wicking anti-microbial liner
The TRAJECTA is tested and certified according to ASTM (F1952-15), CPSC (16
CFR 1203), CE (EN 1078:2012+A1:2012), and AS/NZS (2063:2008) Bicycle Standards
.
WARNING
Use at your own risk : Read the owner’s manual before using this helmet. This helmet complies with U.S. CPSC Safety Standard for bicycle helmets for persons age 5 and older. This helmet has passed EN 1078:2012+A 1 :2012 in conformance with Regulation EU 2016/425. Declaration of Conformity can be found at: https://www.ride100percent.com/declarations This product meets or exceeds CE EN1078:2012+A1:2012, ASTM F1952-15, CPSC 1203, AS/NZS 2063:2008. Standards may vary by region. THIS HELMET IS INTENDED FOR BICYCLES ONLY AND NOT FOR MOTORIZED VEHICLES INCLUDING MOTORCYCLES OR MOPEDS.
WARNING FDR PARENTS
This helmet should not be worn by children while climbing or doing other
activities. There is a risk of hanging or strangulation if the child gets
trapped while wearing this helmet.
WARNING
Bicycle helmet-NOT intended for use in motorsports or by motorcyclists.
Substances such as petrol, paint, adhesives, or cleaning agents can seriously
damage helmets. Make no modifications. Fasten the helmet securely under the
jaw.
WARNING
This helmet is made specifically for the mountain biking rider’s protection
and is made for bicycling only. It cannot guarantee the same safety standards
for a different use. In an accident, the helmet alone does not eliminate the
risk of serious or even mortal injuries. Because every accident scenario is
different, it is impossible to know whether the use of a helmet will provide
partial or complete protection. Studies have shown that you are better off
with a helmet than without one. This helmet can’t protect the user from all
injury or death in case of an accident. Depending on the type of impact,
serious injury or death may even occur in low-speed accidents. This helmet
will not protect against injury from all types of foreseeable or unforeseeable
accidents. It is critical that you ride responsibly and within your skill
level and abilities. Follow all cycling rules and laws on the street, track,
and on the trails. Dangerous and extreme sports can result in serious injury
or death. Sharp objects can pierce this helmet. For maximum protection, the
helmet must be fitted and attached properly to the wearer’s head per the
owner’s manual. Any of the original components of this helmet should not be
modified or removed, otherwise recommended by the manufacturer.
THIS HELMET MAY, AFTER RECEIVING ANY IMPACT, BE DAMAGED TO THE POINT THAT IT IS NO LONGER ADEQUATE TO PROTECT THE HEAD AGAINST ANY FURTHER IMPACTS, AND THAT THIS DAMAGE MAY NOT BE VISIBLE TO THE USER. A HELMET THAT HAS SUSTAINED ANY IMPACT SHOULD BE RETURNED TO THE MANUFACTURER FOR INSPECTION, OR BE DESTROYED AND REPLACED.
WARNINGS AND STANDARDS
- NO HELMET CAN PROTECT THE WEARER AGAINST ALL POSSIBLE IMPACTS.
- THE HELMET IS DESIGNED TO BE RETAINED BY A STRAP UNDER THE LOWER JAW.
- TO BE EFFECTIVE, A HELMET MUST FIT AND BE WORN CORRECTLY. TO CHECK FOR THE CORRECT FIT, PLACE THE HELMET ON THE HEAD AND MAKE ANY ADJUSTMENTS INDICATED. SECURELY FASTEN RETENTION SYSTEM. GRASP THE HELMET AND TRY TO ROTATE IT TO THE FRONT AND REAR. A CORRECTLY FITTED HELMET SHOULD BE COMFORTABLE AND SHOULD NOT MOVE FORWARD TO OBSCURE VISION OR REARWARD TO EXPOSE THE FOREHEAD
- NO ATTACHMENTS SHOULD BE MADE TO THE HELMET EXCEPT THOSE RECOMMENDED BY THE HELMET MANUFACTURER.
- THE HELMET IS DESIGNED TO ABSORB SHOCK BY PARTIAL DESTRUCTION OF THE SHELL AND LINER. THIS DAMAGE MAY NOT BE VISIBLE. THEREFORE, IF SUBJECTED TO A SEVERE BLOW, THE HELMET SHOULD BE DESTROYED AND REPLACED EVEN IF IT APPEARS UNDAMAGED.
- THE HELMET MAY BE DAMAGED AND RENDERED INEFFECTIVE BY PETROLEUM AND PETROLEUM PRODUCTS, CLEANING AGENTS, PAINTS, ADHESIVES AND THE LIKE, WITHOUT THE DAMAGE BEING VISIBLE TO THE USER.
- A HELMET HAS A LIMITED LIFESPAN IN USE AND SHOULD BE REPLACED WHEN IT SHOWS OBVIOUS SIGNS OF WEAR.
- THIS HELMET SHOULD NOT BE USED BY CHILDREN WHILE CLIMBING OR DOING OTHER ACTIVITIES WHERE THERE IS A RISK OF HANGING OR STRANGULATION IF THE CHILD GETS TRAPPED WHILE STILL WEARING THE HELMET.
DISTRIBUTED BY 100% Speedlab, LLC
9630 Aero Drive, San Diego, CA 92123 Ph: 1.619.876.4202 •
www.ride100percent.com
HELMET SIZE AND FITTING
ATTENTION – READ CAREFULLY!
For maximum protection, the helmet must be fitted and attached properly to the
wearer’s head. Users should try different sizes and choose the size that feel
secure and comfortable on the head. The helmet should be adjusted to fit the
user, e.g. the straps positioned so that they do not cover the ears, the
buckle positioned away from the jawbone, and the straps and buckle adjusted to
be both comfortable and firm. The helmet should be positioned on the head to
ensure the intended protection is provided. The helmet should not be adapted
for fitting accessories in a way not recommended by the manufacturer.
INITIAL FIT
Grabbing one chinstrap in each hand, gently pull each strap outward and then pull the helmet over your head. Gently shake your head to the right and to the left. Then shake your head forward and back, or try to turn the helmet with your hands. Rotating the helmet from side to side, observe the movement of your skin about the helmet. The initial helmet fit is correct when skin movement and helmet movement are nearly the same. If it slips in any direction easily, try the next size down.
CHIN STRAPS
Position the chinstraps underneath your chin, towards your neck, and secure
the buckle. Tightly fasten the chin strap by pulling it comfortably tight for
a secure and snug fit. The chinstrap should be as tight as possible, but
without causing pain. Move your head up and down and side-to-side to ensure
that the strap does not interfere with your ability to breathe, talk, swallow,
or turn your head. If so, re-adjust the straps. Make sure the strap and strap
covers are flat against your skin and are not twisted or bunched in any way.
FINAL FIT
With the buckle secured and chinstrap properly and securely fastened, check
for the final fit. Grab the front of the helmet, push up and rotate the helmet
to the rear. Then lift up firmly on the rear of the helmet, push forward, and
try to rotate the helmet off. You should not be able to remove the helmet from
your head while doing either of these steps. If you can remove the helmet or
if it slips in any direction easily, try the next size down. With the straps
properly fastened, you should not be able to pull the helmet off of your head
in any direction. IF THE HELMET STILL DOES NOT FIT PROPERLY AFTER THE ABOVE
STEPS. DO NOT USE THE HELMET. Replace it with a different size or a different
model. Failure to do so may result in serious injury or death in the event of
an accident. To ensure the continued proper fit of this helmet, you should
check the fit during riding and every time it is worn and adjust as needed. To
ensure maximum safety, the helmet should be fit by trying several different
sizes on and choosing the size that feels secure and comfortable on the head.
Warning
A helmet cannot always protect against injury. Any helmet subjected to a
severe impact should be discarded and destroyed. The original components of
this helmet should not be modified or removed, other than as recommended by
the manufacturer. The helmet should not be adapted for the use of accessories
in a way not recommended by the manufacturer. The chinstrap must be used as
furnished and instructed. Do not use a chin cup or wear the strap on the point
of your chin.
WARNING: DO NOT MAKE ANY MODIFICATIONS TO THIS HELMET INCLUDING THE CHIN STRAP, IMPACT-ABSORBING LINER, AND EXTERIOR SHELL. Do not cut, drill or extract parts from the impact-absorbing liner or composite outer shell; you could reduce the helmet’s ability to absorb impact energy. Any modification to the helmet will void all warranties.
COMFORT LINER
The comfort liner is secured to the Smartshock® rotational system and removal is possible by gently pulling up each circular plastic liner cap. The reverse is also true with re-installing the liner by pressing each male liner cap onto the female rotational member that is integrated within the helmet.
VISOR ADJUSTMENT AND REPLACEMENT
The visor is easily adjustable by grasping the visor and lifting up or down until the visor snaps into the final low, middle or high position. In the event of a need for a replacement visor, it can be removed by snapping off each side and repeated by snapping in replacement.
HELMET CARE AND of PACT
WARNING
DO NOT WEAR THE HELMET AFTER AN IMPACT FOR ANY REASON, EVEN IF THERE IS NO
VISIBLE DAMAGE TO THE SHELL. THE HELMET IS MADE FOR ABSORBING IMPACT THROUGH
AN ALTERATION OR PARTIAL DESTRUCTION OF SOME OF ITS PARTS, AND DAMAGE MAY NOT
BE VISIBLE. FOR THIS REASON, THE HELMET MUST BE DESTROYED OR REPLACED AFTER
IMPACT. IF YOU HAVE ANY QUESTIONS WHETHER YOUR HELMET SHOULD BE REPLACED, YOU
CAN CALL YOUR LOCAL DEALER OR 100% FOR FURTHER INSPECTION.
WARNING
DO NOT MAKE ANY MODIFICATION TO THIS HELMET. Do not make any modifications on
the chin strap, or interior. Do not cut, drill or extract any parts from the
helmet. Doing so could reduce the Impact absorption features of the helmet. No
attachments shall be made to the helmet except those recommended by the
manufacturer and any modification to the helmet will void all warranties. Do
not expose this helmet to direct or indirect heat, such as leaving it in the
sun or a hot car. Heat may damage the internal substructure and damage or
destroy the helmet. This helmet has a limited life span and should be replaced
when it shows obvious signs of wear or has been subject to any impact or
accident. The helmet shall be replaced after 5 years from the production date.
Use only genuine parts and accessories.
WARNING
Helmet can be damaged by contact with common substances. This damage may not
be visible to the user. The most common substances that may damage the helmet
include; ammonia, bleach, cleaners and solvents. Which will nullify the
warranty conditions and can cause damage to the helmet potentially rendering
the helmet ineffective in an accident. The protection of this helmet may be
severely reduced by the application of paint, adhesive stickers or transfers,
cleaning fluids or other solvents. Clean the interior and exterior of your
helmet regularly. Use a soft cloth with a mild detergent and lukewarm water
solution to clean both the inside and outside of your helmet. The fit pads are
easily and fully removable, as well as being completely hand washable.
Carefully hand wash and air-dry the fit pads when needed. Moist fit pads
should be removed and dried, out of direct sun exposure.
CRASH REPLACEMENT POLICY
Here at 100% we understand accidents happen. If you were in an accident and
your helmet suffered from any impact, please contact 100% directly and request
a CRA (Crash Replacement Authorization) Number and we will inspect it. Once
inspected, if the damage shows it was indeed from an accident and not
intentional, you may be eligible for a 30% discount on a replacement helmet.
DISPOSAL
Please dispose your helmet at the end of service life. Contact your local
waste disposal company for the correct disposal
LIMITED WARRANTY
All 100% helmets come with a one-year warranty from the date of purchase. The
warranty covers manufacturing defects. The warranty DOES NOT cover the
following: damage caused by an accident, negligence, improper care, normal
wear and tear, scratches, abrasions or other incidental damage to the helmet’s
outer shell. You must have proof of purchase for the warranty to be valid.
Helmet specifications are subject to change without notice.
ASTM F1952-15/CPSC 1203
Taicang ACT Sporting Good Testing Co. No. 35 Zhenghe Road, Ludu Town, Taicang
City, Suzhou, Jiangsu Province,
China 215412
- Phone: 86.512.53230300
- Fax: 86.512.53230369
- Email: info@act-lab.com
COUNTRY OF ORIGIN
Made In China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>