Kingjoy M080 T11 Bluetooth Remote Control Instructions

Kingjoy M080 T11 Bluetooth Remote Control

Product Information

Specifications:

• Model: M080 T11 Bluetooth Remote Control
• Effective Range: Up to 10 meters
• Battery Life: Approximately 10 minutes active time
• Compatibility: Compatible with mobile phones supporting Bluetooth connectivity

Product Usage Instructions

Power On:
Push the switch to the ON position to power on the Bluetooth Remote Control.

Pairing:
When turned on, the Bluetooth remote control enters pairing mode with a blinking LED light. Follow these steps to pair:

1. Open the Bluetooth settings on your mobile phone.
2. Scan for nearby devices and locate “T11”.
3. Select “T11” as the device to pair.
4. Grant access to contacts and call history when prompted.
5. Once paired, the Paired Devices page on your phone will show T11 connected.

Usage:
To capture photos with your phone, press the camera button on the Bluetooth remote control. The green light will blink when the photo is taken.

Power Off:
To turn off the device, push the switch to the OFF position.

Sleep Mode:
If the device fails to establish a connection within 90 seconds, it will enter sleep mode to conserve battery power. It will also go to sleep after 10 minutes of inactivity. To reconnect, press any button on the remote control.

Frequently Asked Questions (FAQ)

• How do I know if the Bluetooth remote control is paired successfully?
  When successfully paired, the Paired Devices page on your phone will display T11 as connected.

• What is the maximum range of operation for the device?
  The device can effectively operate within a range of up to 10 meters from the receiver. Beyond this range, signal quality may degrade or be lost.

• How long does the Bluetooth remote control stay active before going into sleep mode?
  The device remains active for approximately 10 minutes when connected to a mobile phone before entering sleep mode to save battery power.

Bluetooth Instruction

1. Power on: Push the switch to the “ON” position to power on the Bluetooth Remote Control.

2. The Bluetooth remote control enters pairing mode when it is turned on, indicated by a blinking LED light. It then searches for a compatible mobile phone to connect with.

3. OpentheBluetoothpageonyourphonesetting.Next,scanfornearbydevicesandfindtheavailabledevicenamed”T11″.Then, select the device. Finally, wait for the pairing confirmation on your phoneandtheT11.

4. To complete the Bluetooth pairing process, you need to grant access to your contacts and call history. This will allow you to make and receive calls using the Bluetooth device. To do this, go to the “Bluetooth Pairing Request” page and tap on “Allow access to contacts and call history”. Then, tap on “Pair” to finish the pairing.

5. Connection successful, the “Paired Devices” page shows “T11 connected”.

6. The device can operate effectively in a limited area. The maximum distance between the device and the receiver should not exceed 10 meters. Beyond this range, the signal quality may degrade or be lost.

7. You have successfully connected the Bluetooth remote control. To capture photos with your phone, press the camera button. The green light will blink when the photo is taken.

8. Pushtheswitchto”OFF”toturnitoff

9. The Bluetooth remote control attempted to pair with the mobile phone for 90 seconds, but failed to establish a connection. As a result, the device entered sleep mode to conserve battery power.

10. The Bluetooth remote control has a sleep mode to save battery power. When it is connected to a mobile phone, it will stay active for 10 minutes. After that, it will disconnect from the phone and go to sleep. To reconnect, press any button on the remote control.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference
2. this device must acceptancy interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digit device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates.uses and can radiate radio frequency energy and, if not installed and used in accordance with thenstructions, may cause harmful interference to radio communications. However, there is nonguaranteed that interference will not occur in a particular installation.if this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: This device and its antenna(s) must not be co‐located or operation in conjunction with anyother antenna or transmitter
The device has been evaluated to meet general RF exposure requirement, The devicecan be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>