BROKIS CM12203 Knot Glass and Hemp Rope Pendant Light Instruction Manual
- June 13, 2024
- BROKIS
Table of Contents
- CM12203 Knot Glass and Hemp Rope Pendant Light
- COMPONENTS OF PACKAGING:
- CLEANING THE GLASS (2 persons)
- INSTALLING THE CEILING CANOPY
- SWITCHING ON THE LIGHT
- CLEANING/DISASSEMBLING AND REMOVING THE GLASS
- REASSEMBLING THE LIGHT
- BALANCING THE LIGHT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CM12203 Knot Glass and Hemp Rope Pendant Light
Instruction Manual
KNOT SMALL
CILINDRO- PC1034
CM12203
CM12203 Knot Glass and Hemp Rope Pendant Light
INSTALLATION MANUAL
KNOT SMALL Pendent light
https://brokis.sharepoint.com/:f:/s/brokis_sp/Eg_uICQiasNAucRL–MPgvsBQDWcKXjmWj242KqB1EFHdA?e=CQidWF
COMPONENTS OF PACKAGING:
- 1x assembled light
- 1x ceiling bracket with electronics
- 1x ceiling canopy
- 2x hex screws (M6)
- 1x hex key size 2
- 1x hex key size 3
- 1x cotton gloves
- 1x installation manual
WARNING:
Installation must be carried out by a qualified electrician only.
Switch off power at main circuit panel prior to installation!
The manufacturer assumes no liability for damage occurring in transport or
resulting from incorrect installation.
Instalation time: 30 minutes / 1 personhttps://www.brokis.cz/cleaning-
information/
CLEANING THE GLASS (2 persons)
BROKIS applies the highest possible quality standards in manufacturing its
lights. Prior to shipping, each light undergoes several quality controls and
stages of cleaning. Lights may require additional cleaning as a result of
transportation, storage, and the amount of time that passes between packing in
our plant and subsequent unpacking by the client. Therefore, we emphasizes
cleaning the lights prior to installation.
The glass must first be rinsed in hot water, with a dilution of a dish-
detergent used to remove all foreign particles and dust. Eventually repeat
this basic treatment, if necessary. Afterwards the glass must have a second
cleaning using hot water, with a dilution of a de-greaser (such as ammonia or
vinegar). The glass must then be thoroughly rinsed with running hot water.
Eventually repeat this treatment, if necessary. The glass is then thoroughly
dried with a paper towel or a clean soft cotton towel. Only re-assemble the
glass to the lamp body, when completely cooled down.
Do not use mineral spirits, highly concentrated thinners, or other substances
not intended for use on glass surfaces. Also: do not use products, containing
silicones – since they will rapidly attract more dust and grease.
PRIOR TO SHIPPING, THE FUNCTIONALITY OF EACH LIGHT AND ITS COMPONENTS IS
THOROUGHLY TESTED.
THE MANUFACTURER ASSUMES NO LIABILITY FOR THE MISHANDLING OF PRODUCTS.
CONNECTING THE LIGHT TO THE BUILDING WIRING – KNOT
Connect the light to the building wiring according to the connection diagram.
INSTALLING THE CEILING CANOPY
Using the two hex screws (M6) and the hex key, secure the ceiling canopy to
the bracket. Do not sink the screws into the ceiling canopy – we recommend
installing them so that they extend from the ceiling canopy by at least 1 mm.
SWITCHING ON THE LIGHT
Restore power at the main circuit panel and verify that the light works properly.
CLEANING/DISASSEMBLING AND REMOVING THE GLASS
! CLEAN THE INNER PARTS OF THE LIGHT ONLY AFTER IT HAS BEEN TAKEN DOWN AND
DISASSEMBLED !
Using the included hex key, remove the hex screws from the rope end cap.
Remove the cap and leave the end of the rope exposed. 
Expose the spring mechanism in the top of the light by raising
the cover up the rope approximately 20 cm. The spring is held under tension by
a stainless-steel lock with two M4 hex screws. Completely remove these screws
by turning counterclockwise until the spring pushes the lock out of the top of
the light. Raise the lock and spring up the rope to the cover.
The light assembly is now completely loose and unstable.
Raise the entire light assembly along the rope to the spring (approx. 20 cm),
untie the knot beneath the light, and carefully and slowly lower the glass
shade and glass diffuser to remove them from the rope. The metal top and light
source will remain hanging on the suspension cord. You can now clean the glass
components.
REASSEMBLING THE LIGHT
Place the glass diffuser on the glass shade and carefully thread these
components back onto the rope. To make this step easier, first straighten the
end of the rope where the knot was. Begin by passing the rope through the
opening in the glass diffuser and continue through the opening in the bottom
of the glass shade. Raise the glass components along the rope and rejoin them
with the metaltop. Align all these components until they fit together snugly.
Grip the rope directly beneath the glass to hold the light assembly safely on
the rope. Retie the knot in approximately the same position it was before
disassembly and lower the light onto it.Straighten the light as necessary to
achieve the correct look and then lower the lock with spring and insert the
spring into the metal top. Compress the spring as far as possible and secure
the lock with the two hex screws. Tighten the screws so that they do not
protrude from the surface of the lock and then replace the lock cover.
BALANCING THE LIGHT
The light is balanced by rotating the knot and incrementally shifting the metal top in the desired direction. Despite thorough inspection and balancing prior to shipping, each light must be balanced individually following installation. Raise the lock cover approximately 5 cm and leave to hang freely on the rope. Remove the hex screws in the lock and reduce the tension in the spring by allowing it to extend approximately 2 cm. The metal top should still be under enough tension to keep the light assembly stable yet free enough to allow for adjustment. The metal top can now be slightly lifted and shifted until the light is perfectly balanced. Once the light is balanced, compress the spring as far as possible and secure the lock with the two hex screws. Replace the lock cover.
BROKIS S.R.O.
ŠPANIELOVA 1315/25
163 00 PRAHA 6 – ŘEPY
CZECH REPUBLIC
ORG. ID 64940799
VAT ID CZ64940799
C 42174 MĚSTSKÝ SOUD
V PRAZE
TEL +420 567 211 517
TECHNICAL@BROKIS.CZ
INFO@BROKIS.CZ
WWW.BROKIS.CZ
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>