Closer Pets CP400W Large Pet Flap Wall Liner Installation Guide
- June 5, 2024
- Closer Pets
Table of Contents
Closer Pets CP400W Large Pet Flap Wall Liner
IMPORTANT SAFETY INSTRUCTIONS
-
• Read all instructions before installing or using this product.
• Do not allow children to play with this product.
• This product is designed for use with pets only, as described in these instructions. -
• Follow safety instructions for all tools and wear appropriate personal protective equipment.
• Dispose of all packaging material properly.
INSTALLATION GUIDE Wall Liner
For use with Large Cat Flap and Small Dog Door (Ref. 221)
| Wall Thickness (t) | Wall Liners |
|---|
51-99mm (2-4″)
100-149mm (4-6″)
| ****
2
150-199mm (6-8″)| 3
200-249mm (8-10″)| 4
250-299mm (10-12″)| 5
FOR CONTACT
- www.closerpets.com
- +44 (0)1932 700 001
- Designed and Manufactured by Pet Mate Ltd: Lyon Road, Hersham, Surrey KT12 3PU, UK
- Imported to the EU by Closer Pets BV: Newtonlaan 115, 3584 BH Utrecht, The Netherlands Imported to North America by Ani Mate: 104A Longview Street, Conroe, TX 77301, USA
What you’ll need
- Power drill with screwdriver bit
- Drill bits (5mm (3/rn”) for plastic frame)
- Saw
- Waterproof tape
- Silicone sealant or ABS solvent adhesive
- Make a suitably sized hole in the wall and line it with 18mm (11/16″) plywood or similar material to take screws. (We recommend the bottom of the hole is approximately level with your pet’s stomach.)
- Determine the thickness of the wall Determine the number of Wall Liners required (use the table on the front page). Use an additional liner for each 50mm (2″) of wall thickness.
- Assemble a required number of Wall Liners on the internal frame and tape to secure (frame without swinging flap). Carefully cut length to wall thickness (t) less than 6mm (¼”) using a hacksaw or plastic cutting disc. Use moulded lines as a guide to ensure a square cut. Important: Do not cut past the 3rd cut line.
- Tape Wall Liners together, covering the joint prior to inserting. Place any cut wall liners in the middle of the assembly.
- Attach interior frame and Wall Liners to the inside of the wall, using short 13mm (½”) screws.
- Drill out four screw holes in the exterior frame to allow close clearance on screws. (Recommended drill 5mm (3hs”) diameter.)
- Position exterior frame on outside of wall and screw on using 19mm (¼”) screws. Finally, fit screw caps.
A helpful tip: To train your pet to use the cat flap, prop it open at first and use food as an encouragement.
GUARANTEE
We offer a 1-year standard warranty. However, if you register your product at www.closerpets.com/pages/product- registration within 14 days of your purchase you get an additional 2-years warranty and Pet Mate Ltd. will guarantee your product for a period of 3 years from the date of purchase. If you do not have access to a computer, please send details of your purchase with a copy of the receipt along with your name and address, and our Customer Services team will handle this for you. Please get in touch with Closer Pets Customer Services if you have a problem with your purchase. The guarantee is here to protect you if any defect arises due to faulty materials or manufacture. Any defective items will be repaired or replaced free of charge by Pet Mate Ltd, provided the defect has not been caused by neglect, misuse, or normal wear and tear. Your statutory rights are not affected. To get started, register now by scanning the QR code or by following the link here: www.closerpets.com/pages/product-registration
For use with Large Glass Fitting Cat Flap (Ref. 357)
IMPORTANT SAFETY INSTRUCTIONS
- Read all instructions before installing or using this product.
- Do not allow children to play with this product.
- This product is designed for use with pets only, as described in these instructions.
- Follow safety instructions for all tools and wear appropriate personal protective equipment.
- Dispose of all packaging material properly.
| Wall Thickness (t) | Wall Liners |
|---|---|
| 51 · 99mm (2 – 4″) | |
| 100 – 149mm (4 – 6″) | 2 |
| 150 – 199mm (6- 8″) | 3 |
| 200 – 249mm (8 – 1O”) | 4 |
| 250 – 299mm (10 · 12″) | 5 |
FOR CONTACT
www.closerpets.com +44 (0)1932 700 001 N
America (936) 760 4333
Designed and Manufactured by Pet Mate Ltd: Lyon Road, Hersham, Surrey KT12
3PU, UK Imported to the EU by Closer Pets BV: Newtonlaan 115, 3584 BH Utrecht,
The Netherlands Imported to North America by Ani Mate: 104A Longview Street,
Conroe, TX 77301, USA
What you’ll need
- Power drill with screwdriver bit
- Drill bits (5mm (3/rn”) for plastic frame)
- 6 x wall anchors/plugs
- 6 x minimum 13mm (½”) screws
- Saw
- Pliers
- Waterproof tape Silicone sealant or ABS solvent adhesive (optional)
- Make a suitably sized hole in the wall. (We recommend the bottom of the hole is approximately level with your pet’s stomach.)
- Determine the thickness of the wall (t). Determine the number of Wall Liners required (use the table above). Use an additional liner for each 50mm (2″) of wall thickness.
- Assemble a required number of Wall Liners on the internal frame (frame without swinging flap). Carefully cut length to wall thickness (t) using a hacksaw or plastic cutting disc. Use moulded lines as a guide to ensure a square cut. Important: Do not cut past the 3rd cut line.
- Tape Wall Liners together, covering the joint prior to inserting. Place any cut wall liners in the middle of the assembly. If desired, glue Wall Liners together using silicone sealant or ABS solvent adhesive. Place glue into the outer joint(s).
- Snap off the four tabs using pliers or a similar tool so they are flush with the edge of the rim. Important: Ensure you wear safety goggles.
- Attach interior frame and Wall Liners to the inside of the wall, using short 13mm (½”) screws.
- Position exterior frame on the outside of wall and screw on using recommended screws. Finally, fit screw caps.
A helpful tip: To train your pet to use the cat flap, prop it open at first and use food as an encouragement.
GUARANTEE
We offer a 1-year standard warranty. However, if you register your product at www.closerpets.com/pages/product- registration within 14 days of your purchase you get an additional 2-years warranty and Pet Mate Ltd. will guarantee your product for a period of 3 years from the date of purchase. If you do not have access to a computer, please send details of your purchase with a copy of the receipt along with your name and address, and our Customer Services team will handle this for you. Please get in touch with Closer Pets Customer Services if you have a problem with your purchase. The guarantee is here to protect you if any defect arises due to faulty materials or manufacture. Any defective items will be repaired or replaced free of charge by Pet Mate Ltd, provided the defect has not been caused by neglect, misuse, or normal wear and tear. Your statutory rights are not affected. To get started, register now by scanning the QR code or by following the link here: www.closerpets.com/pages/product-registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>