FISHER PAYKEL DD60SCTHX9 Single DishDrawer Dishwasher Installation Guide

FISHER PAYKEL DD60SCTHX9 Single DishDrawer Dishwasher Installation Guidev

SAFETY AND WARNINGS

! WARNING!

| Electric Shock Hazard

Failure to follow this advice may result in electrical shock or death.

•     Before installing the DishDrawer, remove the house fuse or open the circuit breaker.

•     This appliance must be earthed. In the event of a malfunction or breakdown, earthing will

reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment- earthing conductor and an earthing plug.

•     The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.

•     WARNING – Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly earthed.

•     Do not modify the power supply plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box.

! WARNING!

| Cut Hazard

Failure to use caution could result in injury.

•     Take care – panel edges are sharp.

WARNING!

To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Servicing

•  Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken be a Fisher & Paykel trained and supported service technician or qualified person. Installation
• Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.
• The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.
• The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation.
•  This dishwasher is manufactured for indoor use only.
• Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses.
• If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.
• Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should not be reused.
• Failure to install the dishwasher correctly could invalidate any warranty or liability claims.
• Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an unstable product, which may cause damage or injury.
• Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has missing or broken parts, including a damaged power supply cord or plug.
• Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the dishwasher.
• Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.
• Make sure that the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
• Do not install or store the dishwasher where it will be exposed to temperatures below freezing or exposed to weather.
• \D o not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box) to connect the dishwasher to the power supply.
• This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current.
• This appliance is equipped with a cord having an equipment-earthing conductor and a earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.
• EARTHING INSTRUCTIONS – This appliance must be connected to a earthed metal, permanent wiring system, or an equipment-earthing conductor must be run with the circuit conductors and connected to the equipment-earthing terminal or lead on the appliance.
• Ensure the product is not plugged in when fitting custom panels.
• Installation of custom panels requires basic mechanical and electrical skills.
• Installation must comply with your local building and electricity regulations.
•  Failure to install the custom panels correctly could invalidate any warranty or liability claims.
• Installation of this dishwasher requires basic mechanical and electrical skills.
• Be sure to leave these Instructions with the Customer.
• Installation must comply with your local building and electricity regulations.
• At the completion of the dishwasher installation, the Installer must perform the Final Checklist.
• Remove all packaging materials supplied with the dishwasher.
• if the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle, boat or mobile facility containing the product to the service shop at your expense or pay the service
• technician’s travel to the location of the product.

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country,
please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

PARTS SUPPLIED

• Keep all packing materials until the unit has been inspected.
• Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage.
• Fisher & Paykel is not responsible for shipping damage.

TOOLS AND COMPONENTS

Supplied

TOOLS REQUIRED

Not supplied

INSTALL VIDEO

This video provides an overview of what is needed to install a DishDrawer™ Dishwasher. It is intended as an overview only of the installation process and is not intended to be used as a
standalone guide on how to install a DishDrawer™ Dishwasher yourself. Installation should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person.

To access installation videos
Scan the QR code with your smartphone or watch online at: fisherpaykel.com /dishdrawer-install.

PRODUCT DIMENSIONS — DD60SC MODELS

PLAN                                       FRONT

ISOMETRIC                                    PROFILE

DIMENSIONS

ISOMETRIC

*depending on adjustment of levelling feet
including 19mm door panels on adjacent cabinetry
For more information on service requirements, refer to ‘Plumbing & electrical considerations’ and ‘Cabinetry preparation’.

CLEARANCES

CABINETRY CLEARANCES MM

A Minimum clearance to adjacent cupboard door 2
B Minimum clearance to corner cupboard 13

Hose and cord lengths

• Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements.
• If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher & Paykel drain hose extension kit which will extend the drain hoses by 3.6m (part number 525798).

Water connection

• Recommended water temperature: Cold (maximum 60°C)
• 3/4″ BSP (GB20) to suit flat washer
• Ensure water connection complies with local plumbing regulations

SERVICE DIMENSION

| **LEFT SIDE***

MM

| RIGHT **SIDE***

MM

---|---|---
A Length of drain hoses| 2000| 1800
B Length of power cord**| 1650| 1650
C Length of inlet hose| 1650| 1250
Ⓓ Distance from floor to top of hose support| 750 – 883| 750 – 883
E Minimum distance from floor to end of drain hoses**| 500| 500
F Minimum inlet hose radius| 200| 200
G Maximum distance from cabinetry centre of electrical outlet| 450| 450
dimensions taken from the chassis edge where applicable

**excluding plug

***standpipe install illustrated. Distance is the same for all plumbing installs.

|  |

dimensions taken from the chassis edge where applicable
excluding plug
***standpipe install illustrated. Distance is the same for all plumbing installs.

CABINETRY PREPARATION

SERVICE ACCESS

• We recommend locating the service holes on either side of the DishDrawer as shown below.
• If the hole is created through wood, ensure the edges are smooth and rounded
• If the holes is created through metal, ensure the edge protector is fitted.

SERVICE HOLE DIMENSIONS MM

A Maximum distance between rear of cavity and service hole 5
B Maximum distance between shelf and service hole 10
C Minimum diameter of service hole 57

MOISTURE PROTECTION

1. Align the supplied moisture protection tape to the cabinetry as illustrated
   Ensure this area is free of debris before carefully applying the tape to the surface.

SIDE PARTITION

2. If securing via the drawer removal method, ensure the marked locations provide adequate support.
   If there are no side partitions, construct timber bracing to secure the fixings to.

SELECT CABINETRY SECURING METHOD

METHOD A
Secure to cabinetry via brackets Recommended method*

METHOD B

Secure via drawer removal

SECURE TO CABINETRY VIA BRACKETS (METHOD A)

1. Secure all four side brackets to the
   DishDrawer™ Dishwasher, aligning bracket A with slot A and bracket B with slot B.
   Ensure the ends of the brackets are not pushed into the chassis

2. Push the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them.
   Push the product in the positions illustrated to avoid denting the door.

3. Partially open the drawer and remove the first screw cover from\ the trim moulding.

4. Secure to cabinetry via the brackets. Pre-drilling a pilot hole may be required depending on the cabinetry material

5. Replace the trim cover and repeat for the remaining brackets.

SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B)

1. Push the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them.

Push the product in the positions illustrated to avoid denting the door

2. Open the drawer and press both locking tabs back to release

3. Lift the drawer off the runners and carefully set aside on a protected surface. Push runners back in.
   Take care not to pull drawer out too far to prevent any strain on the hoses. Where possible, protect the base of the tub to prevent damage.

4. Secure to cabinetry via all three fixing locations in the chassis.
   Ensure sound insulation is replaced correctly.

5. Before refitting the drawer, ensure the hoses are not twisted. Refit the drawer to the runners and clip into place via both locking tabs.

PLUMBING & ELECTRICAL CONNECTION

1. Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to
   ‘Plumbing & electrical considerations’ for minimum install heights.

2. Pull the hose through the support guide and rest in standpipe.
   Ensure the drain hose does not extend into water retained in the trap; an air gap is required to prevent waste water from siphoning back into the tub

3. Ensure the supplied rubber washer is fitted to the coupling before connecting the inlet hose to tap. Hand-tighten into place.
   Using a spanner or pliers, turn a further 180° to secure. Avoiding over- tightening.
   Do not turn water supply on.
   The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled.

4. Plug product in.

SINK TRAP/WASTE TEE INSTALLATION

1. Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to
   ‘Plumbing & electrical considerations’ for minimum install heights

2. Pull the hose through the drain hose support before threading the wire clip on to the hose and fitting to the supplied hose joiner. Secure using the wire clips.
   Ensure hose is routed straight to the joiner, removing excess drain hose if necessary. Do not shorten the inlet hose.
   Unplug or drill out the waste tee before securing joiner to sink trap or waste tee.

3. Ensure the supplied rubber washer is fitted to the coupling before connecting the inlet hose to tap. Hand-tighten into place.
   Using a spanner or pliers, turn a further 180° to secure. Avoiding over- tightening. Do not turn water supply on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled

4. Plug product in.

TO BE COMPLETED BY THE INSTALLER

Installation

• Check all parts are installed correctly and are secure.
• Ensure DishDrawer™ Dishwasher is securely fastened to the cabinetry and drawer opens and closes freely with no resistance.
• Ensure any packaging or tape securing the racks and spray arm is removed.
• Check the spray arm is in place, mounted correctly and rotate freely.

Plumbing

• Ensure any knock-outs or plugs in drain connection have been drilled out and drain connection has been made.
• The drain hose joiner must not support the weight of excess hose material. Keep drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the highloop.
• Ensure inlet hose has supplied rubber washer fitted, and that it’s tightened.
• If connecting the drain hose to the sink trap, ensure the highloop is a minimum 150mm higher than the drain hose joiner.
• Water softener models: adjust the water softener setting from the default setting to suit the water hardness of the area. Refer to your user guide.
• Ensure water supply is turned off until power is connected and turned on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled.

Electrical

Ensure all electrical tests have been conducted in accordance with local regulations.

Test operation

• Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the control panel.
• Add three cups of water into the drawer.
•  Navigate to RINSE and start the program.
• Repeat for the other drawer.
• After the Rinse cycle has finished, ensure the dishwasher has run and drained correctly.
• Check the water supply has been shut off correctly.
•  Check drainage connections for leaks.
• If site is left without power after installation is complete, ensure water supply is turned off to prevent flooding.

TROUBLESHOOTING

The DishDrawer is beeping continuously

• Refer to the ‘Fault codes’ section of your User guide
  No program indicator lights up when the drawer is opened

• Ensure power is connected and is switched on.

• AUTO POWER-ON may need to be activated. Refer to your User guide for details.
  Drawer doesn’t close properly

• Ensure nothing is obstructing the drawer from closing such as hoses or drawer latches.
  Water appears around water supply and drain connections

• Check hoses, connections and existing plumbing for leaks.

• Check rubber washer and hose clamp are correctly fitted.
  Product is tipping

• Ensure the product is secured to the cabinetry.
  Front panels are misaligned to surrounding cabinetry

• Check the cabinetry is square. Unscrew the product from the cabinetry. Re-secure to the cabinetry.
  If a problem occurs that is not listed, refer to your user guide for additional troubleshooting If after checking these points, you still need assistance, please refer to the Service & Warranty book for warranty details or contact us through our website fisherpaykel.com

Read More About This Manual & Download PDF:

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Install | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>