OTODATA C020 BLE-ES3016 Bluetooth Tracker Installation Guide

OTODATA C020 BLE-ES3016 Bluetooth Tracker Installation Guide

SPECIFICATIONS

INPUT

I2C bus with Bulk M12 for Hall effect, Thermal or level sensors

• REPORTING & OUTPUTS
  Measured parameter (5% variation)
  Low battery
  High/Excessive variation
  Temperature

• Data Interface
  Raw data
  Client mobile app

• Automated Testing
  Connection status
  Battery status

ELECTRICAL SPECIFICATIONS

• Battery Pack
  Hybrid LTC 8.5Ah ~ 3.6 Vdc

RADIO SPECIFICATIONS

• Receiver
  Freq. : 2402.000MHz ~ 2480.000MHz
  Modulation : GFSK

• Transmitter
  Freq. : 2402.000MHz ~ 2480.000MHz
  Modulation : GFSK
  Output: 4.73dBm

ENVIRONMENTAL SPECIFICATIONS

Operating & storage -40C to +85C -40F to 185F
temp. range
Relative humidity range 0% to 100%
Enclosure rating IP67
Warranty 1 year
CERTIFICATIONS
ISED RSS-247, Issue 2 IC Registration: 12649A-BEHT3AD
FCC Part 15 Subpart C FCC ID: 2ADQFBEHT3AD

FEATURES

• Auto-Pairing to any Otodata ready sensor
• Android and IOS apps
• Ready to install

DIMENSIONS

Height 41mm[1.6in], Width 130mm[5.1in], Depth 66mm [2.6in]

ORDERING OPTIONS

ES3016-DH – Digital Hall sensor
ES3016-DT – Digital Temperature sensor
ES3016-DL – Digital Lidar sensor

FCC Statement

This device complies with part 15 of the FCC Rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device is compliant with Industry Canada’s RSS standards for license- exempt radio apparatuses. Authorized use depends on the following two conditions:

1. the device must not create radio interference, and
2. the device user must accept all radio interference, even if this interference could potentially impair its functioning.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Label on Device:

ISED non-interference disclaimer

This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure statement for ISED

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.6 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure statement for FCC

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.

Installation of the device

1. Unpack your device and ensure all parts look good with no damage.

2. If the sensor was shipped disconnected from the box, you can connect it now. Look for the correct position of the connector by aligning the half moon marks.
   

3. Proceed to the Bluetooth pairing by downloading the Otodata TechApp, available for Android or IOS.

4. Start the app on your phone

5. Select BLE Pairing
   

6. Confirm
   

7. Select your device from the displayed list
   

8. Once the process is finished you will be able to use your device in the regular Nee-Vo app.
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>