WORX WG583E, WG583E.9 Cordless Blower, Vacuum, Mulcher Instruction Manual

WORX WG583E, WG583E.9 Cordless Blower, Vacuum, Mulcher Instruction Manual

WG583E, WG583E.9 Cordless Blower, Vacuum, Mulcher

PRODUCT SAFETY

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire
8 and/or serious injury. Save all warnings and instructions for future reference.
The appliance is only to be used with the power supply unit provided with the appliance.

IMPORTANT

READ CAREFULLY BEFORE USE.

KEEP FOR FUTURE REFERENCE.

Safe operating practices

1)Training

1. Read the instructions Be familiar with the controls and the correct use of the machine.

2. Never allow children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the machine, local regulations may restrict the age of the

• Never operate the machine while people, especially children, or pets are

1. Keep in mind,that the operator or user is responsible for accidents or hazards occurring to other people or their

2) Preparation

1. While operating the machine, always wear substantial footwear and long Do not operate the machine when barefoot or wearing open sandals. Avoid wearing clothing that is loose fitting or that has hanging cords or ties.
2. Do not wear loose clothing or jewellery that can be drawn into the air inlet. Keep long hair away from the air

• Obtain ear protection and safety glasses. Wear them at all times while operating the machine.

1. Operate the machine in a recommended position and only on a firm, level
2. Do not operate the machine on a paved or gravel surface where ejected material could cause
3. Before using, always visually inspect to see, that the shredding means,shredding means bolts and other fasteners are secure, the housing is undamaged and that guards and screens are in place.

Replace worn or damaged components in sets to preserve balance. Replace damaged or unreadable labels.

3) Operation

1. Before starting the machine, make certain that the feeding chamber is
2. Keep your face and body away from the feed intake

• Do not allow hands or any other part of the body or clothing inside the feeding chamber, discharge chute, or near any moving part.

1. Keep proper balance and footing at all Do not overreach. Never stand at a higher level than the base of the machine when feeding material into it.
2. Always stand clear of the discharge zone when operating this
3. When feeding material into the machine be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not

• If the cutting mechanism strikes any foreign objects or if the machine should start making any

unusual noise or vibration, immediately shut off the power source and allow the machine to stop. Remove the battery pack from the machine and take the following steps before restarting and operating the machine:

1. inspect for damage;
2. replace or repair any damaged parts;

• check for and tighten any loose
  1. Do not allow processed material to build up in the discharge zone; this may prevent proper discharge and can result in kickback of material through the intake opening.

1. If the machine becomes clogged, shut-off the power source and remove the battery pack from the machine before cleaning
2. Never operate the machine with defective guards or shields, or without safety devices, for example debris collector in

• Keep the power source clean of debris and other accumulations to prevent damage to the power source or possible

1. Do not transport this machine while the power source is
2. Always disconnect the machine from the power supply (e.g. remove the battery pack from the machine)

• whenever you leave the machine,
• before clearing blockages or unclogging chute,
• before checking, cleaning or working on the

1. Avoid using the machine

in bad weather conditions especially when there is a risk of lightning.

4) Maintenance and storage

1. keep all nuts, bolts and screws tight to be sure the appliance is in safe working
2. Check the debris collector frequently for wear or

• Replace worn or damaged

1. Use only genuine replacement parts and

2. Store the machine in a dry place out of the reach of

3. When the machine is stopped for servicing, inspection, or storage, or to change an accessory, shut off the power source, disconnect the machine from the supply and make sure that all moving parts are come to a complete Allow the machine to cool before making any inspections, adjustments, etc. Maintain the machine with care and keep it clean.

4. Store the machine in a dry place out of the reach of children.

5. Always allow the machine to cool before

6. When servicing the shredding means be aware that, even though the power source is switched off due to the interlock feature of the guard, the shredding means can still be

7. Never attempt to override the interlocked feature of the

5) Additional safety instructions for units with bagging attachments

Switch-off the machine before attaching or removing the bag.

BATTERY SAFETY SAFETY WARNINGS FOR BATTERY PACK

1. Do not dismantle, open or shred cells or battery

b)  Do not short-circuit a battery pack. Do not store battery packs

haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by

conductive materials. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

c)  Do not expose battery pack to heat or fire. Avoid storage in direct

sunlight.

• Do not subject battery pack to mechanical

e)  In the event of battery leaking, do not allow the liquid to come

into contact with the skin or

eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.

f) Keep battery pack clean and dry.

1. Wipe the battery pack terminals with a clean dry cloth if they become

h)Battery pack needs to be charged before use. Always refer to this

instruction and use the correct charging procedure.

i) Do not maintain battery pack on charge when not in use.

1. After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.

• Recharge only with the charger specified by Do not use any charger other than that specifically provided for use with the equipment.

l)  Do not use any battery pack which is not designed for use with the

equipment.

1. Keep battery pack out of the reach of

n)  Retain the original product literature for future reference.

1. Remove the battery from the equipment when not in

p)  Dispose of properly.

1. Do not mix cells of different manufacture, capacity, size or type within a

r)   Keep the battery away from microwaves and high pressure.

SYMBOL

COMPONENT LIST

1. HANDLE
2. ON/OFF SWITCH
3. HIGH/LOW SPEED CONTROL BUTTON
4. TUBE RELEASE BUTTON
5. BLOWER TUBE
6. BLOWER TUBE NOZZLE
7. **BATTERY PACKS***
8. . ANTI-STATIC STRIP
9. UPPER VACUUM TUBE
10. TUYAU DE ASPIRATION INFÉRIEUR
11. ROUE
12. SAC DE COLLECTE DES FEUILLES
13. VENTILATEUR BOÎTIER COUVERCLE
14. BOUTONS DE DÉTACHEMENT DU BLOC DE
15. BATTERIE *( VOIR FIG. C)
16.  VOYANT D’ BATTERIE (VOIR FIG. D)

**** TECHNICAL DATA

Type WG583E WG583E.9 (5 -designation of machinery, representative of Cordless Blower

Charger rating

| Input: 100-240 V~

50-60 Hz

Output 1: 20 V  ,

2.0 A *** Output 2: 20 V  ,

2.0 A ***

|

/

Charging time (approx.) Battery pack:

4.0 Ah (1 pc)

4.0 Ah (2 pcs)

|

1              hr

2              hrs

|

/

Machine weight| 4.2 kg (Blow)

5.1 kg (Vac)

| 2.9 kg (Blow)

3.8 kg (Vac)

**Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.
*** Charger output 1 and output 2 mean two ports with the same output voltage and current.

ACCESSORIES

We recommend that you purchase your accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice

NOISE INFORMATION

A weighted sound pressure                 LpA : 84.7 dB(A)
A weighted sound power                     LwA : 99.7 dB(A)
KpA & KwA:                                     3 .0 dB(A)

WARNING: The vibration emission value during actual use of the power tool can differ from the
declared value depending on the ways in which the tool is used dependant on the following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained. Using the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off

and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Helping to minimise your vibration exposure risk. ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Plan your work schedule to spread any high vibration tool use across a number of days.

OPERATION

INTENDED USE:

The blower & Vac is intended for residential use only.
A weighted sound pressure  LpA : 84.7 dB(A)
Use the blower outdoors to move or vacuum yard debris as needed

ASSEMBLY AND OPERATION

Checking the battery condition

NOTE: Fig. A only applies for the battery pack with battery indicator light.

| ****

See Fig. A

Charging the battery pack

NOTE:

•    The batteries are shipped un- charged. Each battery must be fully charged before the first use.

•    Always fully charge the two batteries at same time. More details can be found in charger’s manual.

WARNING! The charger and battery pack are specially

designed to work together, so do not attempt to use any other devices.

Never insert or allow metallic objects into your charger or battery pack connections because of an electrical failure and hazard will occur.

| ****

See Fig. B

Installing and Removing the battery pack

NOTE:

•     This machine will only run when 2 batteries are installed. It is recommended to use the same two batteries and charge the two batteries at the same time.

•    When you use two batteries with different power,the machine will only run to the level of the lowest charged battery

| ****

See Fig.C

Battery indicator light

See details in BATTERY STATUS part

IMPORTANT:

When only one light is illuminated, your battery is overly discharged, even though the machine may still be capable to work. Continuing

to operate your machine with the battery in this discharged condition may reduce the life and performance of your battery.

When no light is illuminated, at least one battery is not fully installed or battery may be defective, please double check the batteries are fully seated into position.

|

See Fig. D

---|---
OPERATION|
Blow mode|
Assembling the Blower Tube and fan housing cover| See Fig. E1,E2,E3
On/Off Switch

WARNING! The tool runs for a few seconds after it has been

switched off.

Let the motor come to a complete standstill before setting the tool down.

|

See Fig. F

Using the Blower

USER TIPS

– Hold the blow tube approximately 8” above the ground when operating the tool.

– Use a sweeping motion from side to side. Advance slowly keeping the accumulated debris/leaves in front of you.

Caution!

Do not blow hard objects such as nails, bolts, or rocks.

|

See Fig.G

Adjusting the blowing speed NOTE: the speed your tool keeps each time you turn it on is the speed when you turned it off last time. If necessary, please readjust the speed.|

See Fig.H

Vacuum mode|
Disassembling the blower tube and fan housing cover| See Fig. I1,I2
Assembling the vacuum Tube and wheel| See Fig. J1,J2
Assembling he Leaf Collection Bag| See Fig. J3
On/Off Switch

WARNING! The tool runs for a few seconds after it has been

switched off.

Let the motor come to a complete standstill before setting the tool down.

| ****

See Fig.F

---|---
Using the Vacuum

NOTE: It is recommended to use high speed for best vacuum performance.

| ****

See Fig. K

Disassembling the vacuum Tube and the Leaf Collection Bag| See Fig.L1,L2
Emptying the Leaf Collection Bag| See Fig. M1,M2
Removing Clogged Debris from the Impeller(no tool included)

NOTE: Ensure to remove the batteries before attempting to clear any debris.

| ****

See Fig. N

BATTERY STATUS (See Fig. D

• Before starting or after use, press the button beside the power indicator light on the machine to check the battery
• During operation, the battery capacity will be indicated automatically by the battery power       __ indicator. The indicator constantly senses and displays the battery condition as follows.                 15
  For the machine with 2 battery packs with different power, the power indicator light displays the battery condition with the lower one of the two batteries

Five green lights (             ) are

illuminated.

| The two batteries are in a highly charged condition.
Two, three or four green lights are il- luminated.| The two batteries have a remaining charge. The more lights are illuminated, the more battery capacity.
Only one green light (       ) is il-

luminated.

| The battery level of at least one battery pack is very low. Please check and charge the battery pack.
No light is illuminated.| At least one battery is not fully installed or battery may be defective.

Only one light is flashing twice per cycle.

| At least one battery is over discharged (please refer to the battery charge condition), please recharge the two batteries at once before use again or storage.
---|---
Only one light is flashing three times per cycle.| At least one battery is hot, wait for them cool down before start again.
Only one light is flashing four times per cycle.| The machine is over load. Remove tool from blowing area and try again.

STORAGE

Store the Blower/Vacuum indoors, in a cool dry location, out of reach of children and animals.

CLEANING THE TOOL

Clean the tool regularly.
Warning! Keep your product dry. Under no circumstances spray with water.
– To clean the tool, use only mild soap and a damp cloth.
16 Do not use any type of detergent, cleaner or solvent which may contain chemicals that could seriously damage the plastic.

ENVIRONMENTAL PROTECTION

Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.

DECLARATION OF CONFORMITY

We, Positec Germany GmbH
Grüner Weg 10, 50825 Cologne, Germany
Declare that the product
Description Battery-operated Blower Vacuum Type WG583E WG583E.9 (5-designation of machinery, representative of battery-operated Blower Vacuum)
Function blowing and picking up debris into a debris collector
Complies with the following Directives: 2006/42/EC, 2014/30/EU
2011/65/EU &(EU)2015/863
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC:

• Conformity Assessment Procedure as per Annex V
• Measured Sound Power Level 7 dB(A)
• Declared Guaranteed Sound Power Level 103 dB(A)

Standards conform to:
EN 60335-1, EN 50636-2-100, EN 62233,
EN ISO 3744, EN 55014-1, EN 55014-2
The person authorized to compile the technical file,
Name Marcel Filz
Address **Positec Germany GmbH Grüner Weg 10, 50825 Cologne, Germany**

Read More About This Manual & Download PDF:

References

• Lawn & Garden Equipment | Innovative Power Tools | WORX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>