FOXTECH Map-A7RII Full-Frame Mapping Camera User Manual
- June 5, 2024
- FOXTECH
Table of Contents
Map-A7R II Full-Frame
Mapping Camera
User Manual
V1.0 2021.12
Description
Disclaimer
Thank you for purchasing this product. You can log in to the website for the
latest product information, technical support, and user manual. It is
recommended that you download and use the latest version of the user manual.
This manual is subject to change without notice.
You can also get product usage information or technical support through
official customer service. Due to different production batches, the appearance
or function parameters are slightly different and will not affect the normal
use of the product.
Please read this statement carefully before using it. Once used, it is deemed
to be an endorsement and acceptance of the entire contents of this statement.
Please read the instruction manual carefully and strictly follow the
instructions in this manual to use this product. Foxtech will not be liable
for any result or loss caused by improper
use, installation, assembly, or modification of users.
Intellectual Property
The intellectual property rights of this product and manual are owned by
Foxtech. Any organization or individual may not copy, reproduce or distribute
in any form without written permission. If you need to quote, you need to
indicate the source, and you should not make any modifications, deletions or
references to this manual.
Specification
Product | A7R II |
---|---|
Pixels | 42.2 megapixels |
pixel size | 4.5um |
Minimum exposure time | 0.8s |
Sensor size | 35.8*23.9mm |
Hot shoes for PPK | Support |
Image size(pixels) | 7952*5304 |
Shutter speed | 30-1/8000 |
Size | 95mm75mm43mm |
Lens | 35mm/40mm/56mm |
Power | 7.2-8.6V |
weight | 219g(Standard),234g(PSDK) |
Parameter Setting | Button/USB |
Date reading | USB/SD card |
Interface Definition
|
Description
| |
Description
---|---|---|---
1| POS Card| 5| Setting
2| Screen| 6| HDMI/USB
3| Skyport| 7| SD Card
4| Restart/Save| 8| Menu
Operating Instructions
- The camera will take a picture automatically, then it can be used via flight controller or manually.
- If the memory card is used for the first time. After the camera self-check, insert the memory card into the camera and click the “OK” button to format, then it can be used normally.
- When debugging the camera, it is recommended to connect the camera to the monitor or TV using an HDMI wire. Camera Shutter Setting
Camera Shutter Setting
Triggered by Relay
-
Connect the shutter release cable to AUX OUT 5 on the flight controller. If there is no PPK module, connect the PPK cable to AUX OUT 6 on the flight controller.
-
Connect the flight controller to the computer using USB or other data links and open the mission planner.
-
Proceed to the CONFIG > FULL PARAMETER LIST and locate the CAM_TRIGG_TYPE parameter. This parameter must show as “1”. If it is not set to 1, change this parameter to 1 before proceeding to the next step.
-
Locate the BRD_PWM_COUNT parameter in the same category, and set it to “4”, meaning that only the top four AUX ports will emit a PWM signal.
-
Locate the RELAY_PIN in the same category and set its value to “54” which means the shutter release cable connects to the flight controller via AUX OUT 5.
-
Locate the CAM_FEEDBACK_PIN parameter in the same category, and set it to “55”, which means the PPK module connects to the flight controller via AUX OUT 6.
Triggered by PWM signal
-
Connect the shutter release cable to AUX OUT 5 on the flight controller. If there is no PPK module, connect the PPK cable to AUX OUT 6 on the flight controller.
-
Connect the flight controller to the computer using USB or other data links and open the mission planner.
-
Proceed to the CONFIG > FULL PARAMETER LIST and reset these four parameters:
-
Set the value of BRD_PWM_COUNT in the same category to “5”, meaning that only the top five AUX ports will emit a PWM signal.
-
Locate the SERVO13_FUNCTION in the same category and set its value to “10” which means the shutter release cable connects to the flight controller 13 port.
-
Locate the CAM_FEEDBACK_PIN parameter in the same category, and set it to “55”, which means the PPK module connects to the flight controller via AUX OUT 6.
The setting camera on APP and PC
https://helpguide.sony.net/ilc/1520/v1/en/index.html
Imaging Edge Mobile for Android
https://www.foxtechfpv.com/product/cameras/map-
a7r-2/imaging_edge_mobile_7.6.0.apk
Please download Imaging Edge Mobile(for IOS) in APP Store.
This content is subject to change.
Download the latest version from
https://www.foxtechfpv.com/foxtech-map-a7r-ii-full-frame-mapping-camera.html
For everyday updates, please follow
Foxtech Facebook page: https://www.facebook.com/foxtechhobby
YouTube Channel:
https://www.youtube.com/user/foxtechonline/featured?view_as=subscribe
©2021 FOXTECH All Rights Reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>