FLYWOO CineRace20 ANALOG Base User Manual
- June 5, 2024
- FLYWOO
Table of Contents
CineRace20 ANALOG Base
Manual
drone introduction
CineRace20 is a new concept and more than a cinewhoop. Inspired by RaceWhoop
designed by Free Zillion. This is a combination of CineWhoop and RaceWhoop!
CineRace s double duct design, is not a simple guard anymore. . It can fly as
flexible as a racing drone, and as stable as Cinewhoop. Pilots can quietly
enjoy the fun of shooting a video without jelly and up to 12 minutes of Super
long flight time with Flywoo’s latest 4S HV 900mah Battery !
All in all, this is an all-around drone that can not only Race but also shoot
a video stably, and at the same time achieve a super long flight time!
Features
- Almost all parts are injection molded. ABS\PC material. More sturdy and durable.
- Very easy to disassemble and install, only fixed by two aluminum columns.
- Pilots can freely combine their favorite colors to be more individual
- Efficient power configuration and reasonable structural design ensure CineRace20 flight stability, low noise, and super long flight time up to 12mins
- No Propellers in view, NO Jello flight Footage, stable flight picture
- With its own power cable output to the SMO camera (If you are using a GoPro 6/7/8 camera, you need to buy an adapter cable )
- Add Flywoo Bt-nano Bluetooth Module
You can use mobile devices to set the parameters of the flight controller.
Personalization Frame Kit
You can freely combine the color frame you like! （Please note： you need to replace the Ducts yourself, all Pre-build Drone colors are determined.） Link: CineRace Frame kit Parts
Specification
Item: CineRace20 Analog w/ Caddx Ant
Weight: 93g (without battery)
FC & ESC : GOKU GN 413 13A AIO
Frame: CineRace20 Frame Kit
Motors: NIN V2 1203PRO 3400Kv
Props: Gemfan D51 -5
VTX: vtx625 450mw
Antenna: Flywoo Circular RHCP 5.8Ghz Ant ( UFL-Length: 115mm \ Tube 45mm )
Battery: Explorer 4S HV 300mAh / Explorer 4S HV 900mAh battery (Not including)
Highly recommended battery
Explorer 4S HV 300mah Battery (You will get good flight time and fly quite
flexible)
Explorer 4S HV 900mah Battery (You will get a super long flight time, and the
flight will be more stable)
Includes
1x Prebuilt and tested CineRace20 Quadcopter
4x D51-5 Props (Pairs)
2x Battery Strap
1x Hardware Set
2/ Configuration and wiring diagram description
Flight control wiring diagram
PID and filter settings
Default serial port settings
UART1: ELRS/TBS/R9M/XM+/DSMX/SBUS receiver UART2: VTX IRX TX
- The selections in XXXX require a HAM license to operate .legally. XXXX Selections are only available on special requests.
- Button function
- FR (blue light), short press the button, the blue light flashing times represent CH1-CH8
- CH (yellow light), long-press the button 2S until the yellow light flashes, and then press the button shortly, the number of flashes of the yellow light represents A-r
- PWR (power), long-press the button 6S until the red light flashes, and then press the button shortly, the number of flashes of the red light represents 5 levels of power
- Long press 105 to unlock 40 channels. (three-color led flashes)
Receiver binding
TBS NANO 915:
When the USB is connected, the green light of the receiver flashes, and then
binds according to the picture operation.
https://www.youtube.com/watch?v=-iNkVcOLITM&ab_channel=Danimal3D
ELRS 2.4G RX:
Bind procedure:
– Supply power to the EL24E/EL24P RX, wait until the LED on the RX is off,
immediately turn off the power, and then repeat again the above steps. When
the RX is powered on for the third time, the LED light will start to double-
flash, which means that the RX enters the binding mode
– Insert the 2.4G ELRS TX to the Radio transmitter, and choose External RF
mode to CRSF protocol, then you can find the ELRS menu from the Radio
systems(Need to copy the ELRS.LUA file to the SD-Card tools first), Enter into
ELRS and press [Bind], the LED on the RX module will get to be solid if bind
successfully.
– Receiver LED status meanings:
EL24E/EL24P RX: LED solid means to bind successful or Connection established;
LED double-flash means in bind mode; LED flash slowly means no signal
connection from the TX module; LED flash fast means in WIFI hotspot mode, you
can connect the WIFI of the RX and upgrade the firmware of the RX via visit
10.0.0.1 from the web browser(password: expresslrs)
R9MM FCC ACCESS OTA：
Make sure your remote control supports ACCESS protocol, then follow the link
to register and bind
https://www.youtube.com/watch?v=az5hDdNBcjg&t=9s&ab_channel=FrSkyRC
If the remote control is ACCST protocol, please bind as follows:
1/ Put these two files into the firmware directory of the SD card of the
remote control.
R9MM firmware: FW-R9MM-ACCST_v20190201
R9M TX module: FW-R9M-ACCST-20190117
2/ Insert the R9M TX module and write the firmware you need
3/ To write the firmware of the R9MM receiver, you need to remove the R9MM
receiver, and then write the firmware by connecting to the S.PORT
port.
4/ After both R9M TX and R9MM RX are written into the ACCST firmware.
Binding method:
1/ Press and hold the button of RX, power on, the red and green lights are
always on.
2/ Then after R9MM selects binding, RX red light flashes, and then exit
3/ RX is powered on again, and only green light is displayed, indicating that
the binding is successful.
XM+ receiver:
1/ Press the XM+ receiver button, and USB power supply, the red and green
lights are always on
2/ The remote control turns on the binding mode, and the green light flashes
to indicate successful binding, turn off and restart
3-1/ Then set the
corresponding serial port and receiver protocol to ensure the normal output of
each channel of the receiver.
Mode setting:
Set the ARM switch and flight mode switch, AUX* corresponds to the remote control switch, and the yellow area mark is turned
Motor test:
Unload the propeller, test the rotation direction of the motor, turn on the
safety switch, and test the rotation of the motors one by one.
Flight firmware upgrade and write default CLI
1/ Activate DFU mode
2/ BF Configurator will display to enter DFU mode. If it does not enter DFU mode, it may be that the driver is not installed. The driver can be installed using IMPULSE RC software
Driver software:
https://impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
3/ Then load the local HEX firmware and wait for the flashing to complete. A
green progress bar is displayed to indicate completion, and DFU will become a
COM port
4/ After the connection is entered, it is a blank interface, you need to write
CLI commands, Factory CLI LINK: https://flywoo.net/pages/manual
5/ If the command is not restarted after writing the command, please write
SAVE and press Enter to save, and the FC will restart
6/ Then all functions of FC return to normal.
Configuration table
| CineRace20 Analog | CineRace20 Analog Pro | CineRace20 Polar Nano |
|---|---|---|
| Color | Grey | Color |
| FC \ESC | GOKU 413SAIO 13A MO | FC\ESC |
| \ESC** | GOKU 405S 20A AIR | |
| Camera | Caddx Ant | Camera |
Polar Nano
VTX| VTX625 450mw| VTX| HM850 850mw| VTX| Vista
Antenna| Plywood circular RHCP 5.8Ghz Antenna
( UFL–Length: 115mm \ Tube 45mm)
| Antenna| Plywood circular RHCP 5.8Ghz Antenna
(UFL– Length: 115mm \ Tube 45mm)
| Antenna| Plywood circular LHCP 5.8Ghz Antenna
( UFL –Length: 115mm \ Tube 45mm)
Motor| Nin V2 1203PRO 3400kv| Motor| Nin V2 1203PRO 3400kv|
Motor| Nin V2 1203PRO 3400kv
Propeller| Gemfan D51-5 blade| Propeller| Gemfan D51-5 blade|
Propeller| Gemfan D51-5 blade
Bluetooth, module| | Bluetooth, module| YES| Bluetooth,
module| YES
Microphone module| | Microphone module| YES|
Microphone module| \
Battery| Explorer 4S 300mah HV
Explorer 4S 900mah HV| Battery| Explorer 4S 300mah HV
Explorer 4S 900mah HV| Battery| Explorer 4S 300mah HV
Explorer 4S 900mah HV
Flight Time (Without Caddx Peanut)| 300mAh\7mins 900mAh\15mins
30s| Flight Time (Without Caddx Peanut)| 300mAh\7mins 900mAh\1
Smins 30s| Flight Time (Without Caddx Peanut)| 300mAh\6mins
900mAh\12mins 30s
Flight Time (With
CaddxPeanut| 300mAh\4mins 30s 900mAh\12mins| Flight Time (With
CaddxPeanut)| 300mAh\4mins 30s 900mAh \12mins| Flight Time
(With
CaddxPeanut)| 300mAh\3mins 30s 900mAh\10mins
Weight| 93.2g (Without Battery)| Weight| 94.7g (Without Battery)|
Weight| 111.7g (Without Battery)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>