SOUNDPEATS S5 Wireless Earbuds User Guide

: June 5, 2024
: SoundPEATS

Table of Contents

First use
Reset
Wearing
Product Diagram
Control
Q&A
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SOUNDPEATS S5 Wireless Earbuds

SOUNDPEATS-S5-Wireless-Earbuds

First use

Please open the lid of the charging case, take out the two earbuds, and tear off the insulating film on the earphone charging contacts, then put the earbuds back into the charging case.

Open the charging case, take out the two earbuds, the earbuds will automatically power on and start to paring with each other. One earbud’s white LED is on, another one is blinking with white and red light, which indicates that the earbuds has entered pairing mode.
Turn on the bluetooth of your device, and please choose“SOUNDPEATS S5”inthe list to pair, then the earbuds will connect with your device.

Reset

Clear the pairing data from your device.
Put both earbuds into the charging case. Make sure they are in charging status.
Then long press the MFB of both earbuds for 10 seconds at the same time until the LED indicator in both earbuds flash white and red twice. The reset finish.

Wearing

Identify the left and right earphones. Adjust the earphones to fit your ears.
Right and wrong way of wearing.

Product Diagram

SOUNDPEATS-S5-Wireless-Earbuds-Q&A

Control

Power on| Automatic: Open the charging case, take out the earbuds, the earbuds will automatically power on Manual: Long press the MFB for 1.5 seconds in shutdown status
---|---
Power Oﬀ| Automatic: Place the earbuds back into the charging case.\

Manual: Long press the MFB for 10 seconds in working status.

Q&A

Q1: What does the LED indicator mean when the earphone is charging?
During the charging, the LED show red light, it will turn off when full charged.

Q2: What does the LED indicator on the charging case mean?
During the charging, the indicator light flashes to show the remaining power of the charging case.
The first white LED light flashes to show 0-24% remaining power of the charging case.
The first white LED light is on and the second LED flashes to show 25%-49% remaining power.
Two white LED lights are on and the third LED flashes to show 50%-74% remainingpower of the charging case.
Three white LED lights are on and the fourth LED light flashes to show 75%-99% remaining power of the charging case.
4 lights are all on when full charged.
SOUNDPEATS-S5-Wireless-Earbuds-Q&A

Q3: How to charge the charging case?

Connect to a Type-C charging adapter charge it.(Charging current does not exceed 1A).
When not using for a long time, please charge it once every three months at least.

Q4: Why does the earphone still connect to the mobile phone after putting it back into the charging case ?

The charging case has no power. The earphone will not power off in charging case when charging case has no power.
Make sure the earphone is properly placed in the charging case. Please try to clean the contact area between the charging box and the earphones with a soft cloth, keep the charging metal piece and pin clean.

Q5: Why is the playtime not as described?

A single charge not allow the earbuds to last 20 hours. 5 hours playtime per charge and another 3 recharges by charging case.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.