SoundPEATS S5 True Wireless Earbuds User Guide
- June 5, 2024
- SoundPEATS
Table of Contents
SoundPEATS S5 True Wireless Earbuds
User Guide
First use
Please open the lid of the charging case, take out the two earbuds, and tear off the insulating film on the earphone charging contacts, then put the earbuds back into the charging case.
- Open the charging case, and take out the two earbuds, the earbuds will automatically power on and start to paring with each other. One earbud’s white LED is on, another one is blinking with white and red light, which indicates that the earbuds have entered pairing mode.
- Turn on the Bluetooth of your device, and please choose“SOUNDPEATS S5”in the list to pair, then the earbuds will connect with your device.
Reset
- Clear the pairing data from your device.
- Put both earbuds into the charging case. Make sure they are in charging status.
- Then long-press the MFB of both earbuds for 10 seconds at the same time until the LED indicator in both earbuds flashes white and red twice. The reset finished.
Wearing
- Identify the left and right earphones. Adjust the earphones to fit your ears.
- Right and wrong way of wearing.
Product Diagram
Control
Power on| Automatic: Open the charging case, take out the earbuds, the earbuds
will automatically power on
Manual: Long press the MFB for 1.5 seconds in shutdown status
---|---
Power Off| Automatic: Place the earbuds back into the charging case.
Manual: Long press the MFB for 10 seconds in working status.
Play/Pause| Double-tap MFB
Volume-| Tap MFB(L) once
Volume+| Tap MFB(R) once
Play Previous| Press the MFB(L) for 1.5 seconds
Play Next| Press the MFB(R) for 1.5 seconds
Answer/Hang-up phone call| Double-tap MFB(L/R)
Reject phone call| Press the MFB(L/R for 1.5 seconds
Switch between two calls| Long press the MFB(L/R )for 2 seconds
Manually enter into pairing
mode| Long press the MFB(L/R )for 6 seconds
Activate voice assistant| Triple tap MFB(L/R )
Q&A
Q1: What does the LED indicator mean when the earphone is charging?
During the charging, the LED shows red light, it will turn off when fully
charged.
Q2: What does the LED indicator on the charging case mean?
During the charging, the indicator light flashes to show the remaining power
of the charging case.
The first white LED light flashes to show 0-24% remaining power of the
charging case.
The first white LED light is on and the second LED flashes to show 25%-49%
remaining power.
Two white LED lights are on and the third LED flashes to show 50%-74%
remaining power of the charging case.
Three white LED lights are on and the fourth LED light flashes to show 75%-99%
remaining power of the charging case. 4 lights are all on when fully charged.
Q3: How to charge the charging case?
- Connect to a Type-C charging adapter and charge it. (Charging current does not exceed 1A).
- When not used for a long time, please charge it once every three months at least.
Q4: Why does the earphone still connect to the mobile phone after putting it back into the charging case?
- The charging case has no power. The earphone will not power off in the charging case when the charging case has no power.
- Make sure the earphone is properly placed in the charging case. Please try to clean the contact area between the charging box and the earphones with a soft cloth, keep the charging metal piece and pin clean.
Q5: Why is the playtime not as described?
A single charge does not allow the earbuds to last 20 hours. 5 hours of
playtime per charge and another 3 recharges by charging case.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited.
Room 1308-1309, Building B, Huaihai Square, Chuangye Road, Longhua District,
Shenzhen, China. 518109
support@soundpeatsaudio.com
www.soundpeatsaudio.com
Company：Qing UG(haftungsbeschränkt)
Address： Undinestr. 7, 12203 Berlin Germany
FCC ID: 2AFTU-DD023
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>