pecron S1000 Outdoor Portable Power Station User Manual

pecron S1000 Outdoor Portable Power Station

Introduction

Pecron S1000/Sl500 is a multi-use outdoor portable power station, it adopted a three-dimensional spinet-based lithium-ion battery made up of a first-class EVE automotive-grade power cell guaranteeing it’s great stability and longevity.

• Pure Sine Wave output
• DC output 12VI0A USB*4 QC3.0
• LCD Smart Display
• Super Fast Charging
• Support Three Ways Charging(AC charging, Car charging and Solar charging) With l,461.6Wh(l,028Wh) lithium-ion battery pack at its core and a built-in pure sine wave inverter, Sl500(S1000) is capable of providing 1,500(1,000) watts power to run a wide range of appliances, such as mobile phones, refrigerator,juicer, projector, electric saw, or even your Tesla; It can be widely used in the area of mobile working, outdoor recreation, camping, rescuing, environment protection, emergency communication, power outage backup and so on. Please read the user manual carefully before using, and keep the purchase receipt as a proof of purchase for any warranty claim.

Function Instruction

1. Power Switch: Press the power switch to start the unit, the general information of the power station will be displayed within 2 seconds at 100% brightness; press the button one more time to decrease the brightness to 50%; Press and hold the button for I second to turn the unit off.
2. DC Switch: Press and hold the DC switch for 1 second, the USB and 12V DC output ports will be activated, at the same time, the LCD screen shows the battery level, estimated discharging time(H), discharge(load) wattages, “DC OUT” symbol (shown as Picture!); Press the DC switch one more time to show the discharging voltage; Press and hold the DC switch for 1 second to deactivate the USB and DC output.
3. AC Switch: Press and hold the AC switch for 1 second, the AC output will be  activated, at the same time, the LCD screen shows battery level, AC discharge time(H), AC discharge(load) wattages, load percentage, “AC OUT” symbol; Press the AC switch once more time to show AC discharge voltage+ PF value (shown as Picture 2). Press and hold the AC switch for 1 second to tum off the the AC output function.
4. OLCD smart display screen
5. USB QC3.0: Turn on the DC Switch to use the USB function
6. Air Vent
7. (T DC Output Port: 16MF two-prong aviation plug(1 is positive, 2 is negative), it can supply (12V 10A) power to it’s connected devices when DC switch is turned on.
8. DC Input Port: 16MF four-prong aviation plug(1822 are positive, 384 are negative), charging the through this port when the battery is nunning now(29.4V 10A)
9. AC Output Socket*2: When AC switch turned on, it can produce up to I500(1 000) wattages power to run your appliances.
10. Air Vent

Product Information

3

|

AC Output

| 220V/50Hz

（Version）

| AC110V60Hz

（Version）

| AC100V50Hz

（Version）

4

| Output Waveform|

Pure sine wave

5| DC Output| DC 12Vl0A USB*4（QC3.0）
5| Cell Type| 18650-20P7S( 3.6V2.9Ah)
6| Battery Capacity| 1028Wh{25.2V40.8Ah)       I          1461.6Wh{25.2V58Ah)
7| Battery Type| Lithium-ion
9| Charging Time| 5~6H(2~3H for pro version)| 7~8H (3~4H for pro version)

10

| Charging Voltage And Current|

DC29.4V9A      Solar Panel 36V 20A( MAX)

11

| Protection Function| Over-voltage, low-voltage, over-temperature, overload, AC short circuit protection

12

|

Working Temperature

| 0°C~45°C（Charge）

-20°C~60°C（Discharge）

13

| Product Dimension|

L352Wl87H260( mm)

14| Shell Material| UL94-V0      PC+ABS
16| Net Weight| 22.4lbs(l 0.2kg)| 25lbs(11.6kg)

WORKING CONDITIONS

**Specifications

**

Protection Instructions

Operating Instructions And Precautions:

To ensure safety during the transportation, the power station is in low battery capacity status when you receive it, please charge the unit to full before using. Please use Pecron original charger for, or 36V 200-300W solar panel for faster charging experience. Please disconnect the charger after the unit is fullycharged. Using third-party charger or adapter could result in product damage or even safety hazards.
Prior To Using
Precautions:

1. Please make sure the input voltage and frequency fits into the unit

2. Please make sure the appliance consumption power is below its rated
   power. It is suggested not to run devices at or over its 80% loadin gcapacity for prolonged time Fail to take the precautions could result in product failutre.

   • You can get larger capacity and wattages power stations from www.pecron.com if S series does not meet your needs. Remark: Some appliances require extra power to start up; In general, the startingpower for inductive load equipments(e.g. motor, compressor, fluorescent lamps) is 3-8 times higher than its rated power. The BMS will activate the over-load protection and shut down all outputs if the total output exceeds its loading capacity.

3. The BMS will activated and shut down the outputs when the following situations happen

4. OWhen the total loading power exceeds the power station rated power.

5. Short circuit in AC output

6. The temperature of the battery pack is too high

7. The voltage of the battery pack is too low

How To Use AC:

• Step 1: Press “ON/OFF” to start the power station; Press and hold “AC ON/OFF” for I second to activate AC output function
• Step 2: Check your device working wattage and make sure it does not exceed the rated power of the unit(1500W).
• Step 3: Plug your device into the AC outlets before turn it on.
• Step 4: Press the “ON/OFF” button to shut down the unit after finishing using.
• Step 5: Please charge the power station on time when the battery is running low.

6.3 How To Charge:
You can charge your Pecron through the following methods:

1. Use Pecron official charger to charge your Pecron from a standard wall Outlet.
2. Use 29.4-40V solar panel to charge: S1000/S1500 is universally compatible with third party (MC4) solar panels. For any 18V panels, you will need to get two of them in series connection(18V*2-36V) to charge S1500, this including Pecron Auroral00
3. Use car adapter to charge: You can use the 4 in l adapter to charge your Pecron from your vehicle cigarette port. Make sure to start your vehicle before charging.

Notes:

1. US series standard power adapter can be used for Pecron S series only, please don’t use it to charge other device.
2. When charing your Pecron through PV input(solar or vehicle), make sure to connect the outlet with correct positive and negative pins.
3. Please make sure to charge your Pecron at least once for every six months if it is left unused for a prolonged time.

How To Use 12V DC and USB ports:

Two-prong aviation DC outlet: Press and hold the DC switch for second to activate/deactivate the DC output function, this outlet can produce up to 12V, 10A(120W) power to run your

DC devices 4x USB QC3.0: Activate the USB function by pressing and holding the DC switch for I second(Same as the DC outlet).

Product Testing

Conditional Testing

Function TestING

• Discharging test with load
• Charging test
• 12V DC output test
• USB output test

TROUBLESHOOTING

PACKAGE LIST

References

• Pecron: All Around Portable Power Expert – PECRON LLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>