MINN KOTA i-Pilot Remote- Legacy Remote User Guide

Table of Contents

PRODUCT

FIG-1

FIG-3

FIG-4

ENGAGING SPOT LOCK

Press the Spot Lock button on the remote.
The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down buttons. Pressing the Spot Lock button again or waiting for three seconds accepts the memory location.

DISENGAGING SPOT LOCK

To disengage Spot Lock press any of these buttons:

RE-ENGAGE A SAVED SPOT LOCK LOCATION

Manually navigate the boat to within a quarter mile of the saved Spot Lock location. Due to safety reasons,i- Pilot will not re-engage a saved Spot Lock location greater than a quarter mile away.
Press the Spot Lock Recall button on the remote.
The Memory Location icon will flash on the remote LCD for three seconds allowing you to choose a memory location by pressing the Speed Up or Speed Down buttons. Pressing the Spot Lock Recall button again or waiting for three seconds accepts the memory location.

SPOT LOCK ESCAPE

If the Spot Lock button is accidentally hit, press the Record Pause/Escape button or any manual navigation button within three seconds to cancel the command.

ENGAGING CRUISE CONTROL

Press the Cruise Control button on the remote.
The current GPS speed will flash, displaying your current speed as the target GPS speed on the remote LCD for three seconds.
Press the Speed Up or Speed Down buttons to increase or decrease the target speed or press the Cruise Control button again to engage Cruise Control immediately.

DISENGAGE CRUISE CONTROL

ADJUSTING TARGET SPEED WITH CRUISE CONTROL ENGAGED

With Cruise Control engaged press the Speed Up or Speed Down buttons to adjust the target speed by 0.1 MPH increments.

ENGAGING ADVANCED AUTOPILOT AND AUTOPILOT

To engage Advanced AutoPilot, press the AutoPilot button once. To engage AutoPilot, press and hold the AutoPilot button for two seconds.
The Advanced AutoPilot or AutoPilot icon will be displayed on the remote LCD.
To adjust desired heading, manually steer motor to new heading. i-Pilot will lock onto new heading.

RECORDING A TRACK

Press the Record button on the remote.
The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down buttons. Pressing the Record button again or waiting for three seconds accepts the memory location.
The REC icon will be displayed on the remote LCD. Remember this will be the start point on the track.
Navigate the boat along the desired path or course. AutoPilot and/or Cruise Control can be used while recording a track.
Press the Record button on the remote again to stop the recording. The recording will end automatically if the two-mile distance limit is reached for the track or if one of the following buttons are pressed: Spot Lock, Spot Lock Recall, Track to End or Track to Start.

PAUSE AND RESUME A RECORDING

While recording a track press the Record Pause/Escape button.
The record icon will flash on the remote LCD.
i-Pilot has now paused the recording of the track.
If the boat moves farther than a quarter mile from where the Record Pause/Escape button was pressed, the recorded track will be ended and saved to the memory location previously selected.
When ready to resume recording, navigate the boat just ahead of where the Record Pause/Escape button was pushed. Failure to do this may cause erratic play back of a track.
Push the Record Pause/Escape button.
The record icon will stop flashing on the remote LCD.
i-Pilot is now recording again and adding to the track that was paused.

REPLAYING A TRACK(TRACK TO START / TRACK TO END)

Manually navigate the boat to within a quarter-mile of the saved track. Due to safety reasons, i-Pilot will not re-engage a saved track greater than a quarter-mile away.
Press the Track to Start or Track to End button on the remote.
The Memory Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Up or Speed Down button. Pressing the button pressed in step 2 again or waiting for three seconds accepts the memory location.
Adjust motor speed to desired setting to engage and navigate track automatically.

RECORD, TRACK TO END AND TRACK TO START ESCAPE

If the Record, Track to Start or Track to End button is accidentally hit, press Record Pause/Escape button within three seconds on the remote to cancel the command.