smartbitt 1200va UPS System User Manual
- June 5, 2024
- smartbitt
Table of Contents
smartbitt 1200va UPS System
Read all the safety instructions
carefully to correctly and safely use and operate Smartbitt UPS To avoid electric shock hazard or fire risk, place your UPS in an area where temperature and humidity don’t exceed the operative parameters of your UPS and make sure the environment is free of conductive or combustible contaminants. To reduce overheating risk of your UPS, do not cover the ventilation slots, avoid continuous exposure to direct sunlight and don’t place it near appliances that produce heat like heaters or boilers. Do not connect devices or appliances functioning with alternating current motors, like drills, chainsaws, microwaves, vacuum cleaners, refrigerators, or medical, vital support or industrial equipment. Do not connect your UPS to a surge protector, power strip or AVR. Do not power on your UPS with its power cord connected to its own power outlets. Do not expose to liquids that may leak inside the device. In case of emergency, press the power button making sure that the UPS shuts down, then disconnect its power cord from the AC outlet. Disconnect the UPS before cleaning it, do not use liquid detergent or scouring powder. Do not try to replace batteries, please contact Smartbitt Technical Support to get information about battery replacement. Only qualified personnel should replace batteries in case it is required. Replacement must be done with caution. The same kind and capacity of batteries shall be used.Nonauthorized personnel should abstain from making the replacement. Batteries must not be exposed to fire and have to be disposed of properly. Mistreat of the batteries can cause them to explode. The materials contained inside the batteries is dangerous for eyes and skin, in case of contact with these materials, rinse thoroughly and consult your doctor immediately.
ELECTRIC SHOCK HAZARD
DURING BATTERIES REPLACEMENT
In case of requiring battery replacement, please contact our Technical Support where you will be advised on the issue. This product meets with the actual European Union environmental and security regulations. If you need any further information about this or any other issue, do not hesitate to contact us, an expert will provide the necessary care.
WHAT’S IN THE BOX
The box should include the following elements:
Thanks for purchase Smartbitt Products.
Your UPS is an uninterruptible power supply system with interactive technology. It is a device designed to protect your electronic devices and appliances which are sensitive to different power faults and interferences, including total power fail. This device is equipped with various technologies capable of making your electric devices to work properly for extra time
Important Note.
Before installation, inspect the unit. Make sure that none of the elements in
the box is damaged. In case you find any damaged part, please contact your
vendor.
SBNB500
- Switch On / Off Button
- LED’S Status indicator
- Electronic Breaker
- Power Cord
- Four Outlets (With Backup)
SBNB750 /1000USB
- Switch On/Off Button
- LED’S Status Indicator
- Phone Line Protector
- Electronic Breaker
- Power Cord
- Six Outlets (With Backup)
- USB Port (USB models)
SBNB1200
- Switch On /Oft Button
- LED’s Status Indicator
- USB Port for Monitoring Software
- Power Cord
- Electronic Breaker
- Phone Line Protector
- Eight Outlets (With Backup)
-
Installation and Storage Conditions.
Place your UPS in a protected area, free from excesive dust and adequate ventilation. To avoid any interference, do not place your UPS less than 20 ems away from other devices.
Do not power on your UPS where temperature exceeds 40°C degrees or relative humidity is above 90%. -
Connection to power outlet and first battery charge.
Connect the plug of your UPS to the power outlet. To get the best performance of the battery, we suggest to charge it for 8 hours before its first use, afterwards, the UPS will charge its battery automatically while it’s connected to the electrical network. -
Power on/off of the UPS
Hold the power button for 3 seconds for either power on or shut down your UPS. -
Connection of your devices to the UPS
Connect your devices to the power outlets on the rear panel of your UPS. After this, when you power on your UPS your devices will be protected.
DO NOT CONNECT A POWER STRIP, SURGE PROTECTOR OR AVR TO THE UPS OUTLETS.
-
Connection of the telephone line protector.
Connect the telephone line to one of the connectors in the rear panel of your UPS. Connect a telephone cable to the remaining connector available and to the device you are willing to protect.- THIS DOES NOT APPLY FOR MODELS WITHOUT TELEPHONE LINE PROTECTION
-
Connection of the USB interface cable.
This function allows you to control and monitor your UPS through the included software. Connect the USB cable to the USB port of your computer.- APPLIES ONLY WITH USB COMPATIBLE MODELS
IMPORTANT
Never connect a laser printer to your UPS, input current generated from this
kind of devices could damage your UPS. Do not connect either appliances with
alternating current motors such as drills, chainsaws, etc.
AUDIBLE ALAMARS
TO HELP YOU TO IDENTIFY COMMON UPS PROBLEMS.
The UPS features an audible alarm which indicates when it is in a different status than normal, description of the audible alarms is as follows:
Troubleshooting
PROBLEM | POSSIBLE CAUSE | ACTION |
---|
LED status indicators not turning on
| Low Battery| Charge the UPS for at least 8 hours without any connected
devices.
Battery Failure| Replace battery, please contact Technical Support.
UPS not turned on| Press power on button, make sure that the UPS is
correctly
Alarm continuously active
|
A tone every 10 seconds. Power outage
|
If there’s not a power outage, make su the UPS is correctly connected to the power source.
A tone every second. Low Battery| Charge the UPS for at least 8 hours without any connected devices.
If after this, the problem continues, contact Technical Support for battery diagnosis and replacement.
A tone every 0.5 seconds. Overload
|
Disconnect devices from your UPS un the total load of connected devices is below the UPS maximum capacity.
Make sure your devices not exceed the maximum capacity.
A tone every 2 seconds. Battery fail.
|
Contact Technical support for diagnos and possible battery replacement.
A continuous tone. Unknown failure
|
Contact Technical Support
PROBLEM | POSSIBLE CAUSE | ACTION |
---|
During power outage, battery lasts too little.
|
UPS Overload
|
Disconnect some devices and verify the connected devices load do
not exceed the UPS capacity.
Battery voltage is too low
|
Charge the UPS for 8 hours without any devices connected .
Battery life is depleted
|
Replace battery.
Contact Technical Support.
UPS functioning in backup mode without a power outage
|
Power cord is not correctly connected or it’s broken.
|
Make sure the power cord is correctly connected to the power source,
if this is not the problem, contact Technical Support.
Technical Specifications
The backup time may vary depending on the load connected to UPS.
Consumption Table
Phone Mobil Charger | average consumption | SW |
---|---|---|
Multichannel Amplificator | average consumption | 120W |
Audio Minicomponent | average consumption | 60W |
Scanner | average consumption | lSOW |
Printer | Inkjet Printers | 27W |
PC (monitor) | CRT promedio 17 inches | 70W |
PC (monitor) | LCD, 19 inches | 100W |
PC (monitor) | LCD, 21 inches | 120W |
PC Netbook | 10.1 inches | 40W |
PC LapTop | 15 inches | 6SW |
PC Desktop (CPU) | average consumption | 170W |
PC Tower | average consumption | 400W |
PC iMac (CPU) | Apple | 36SW |
Digital Clock | average consumption | SW |
DVD Player | average consumption | 3SW |
Blu-Ray | average consumption | 60W |
Switch/HUB | 8 Ports | 8W |
lnalambric Phone (Dock) | average consumption | 2SW |
TV | CRT Color , 21″, average consumption | 200W |
TV | LED, 32 inches | 60W |
TV | LED, 40 inches | 100W |
TV | LED, 55 inches | 190W |
TV | LED, 60 inches | 230W |
TV | LED, 80 inches | 280W |
TV | LCD, 19 inches | 3SW |
TV | LCD, 21 inches | llSW |
TV | LCD, 32 inches | 1S6W |
TV | LCD, 34 inches | 200W |
TV | LCD 37 inches | 236W |
TV | LCD, 42 inches | 322W |
TV | LCD, 50 inches | 464W |
TV | Plasma , 42 inches | 474W |
TV | Plasma , 50-56 inches | 18W |
Video game Console | Nintendo Wii | 34W |
Video game Console | Nintendo Wii U | 23W |
Video game Console | Playstation 5 | 230W |
Video game Console | PS2 | 194W |
Video game Console | PS3 | 237W |
Video game Console | PS4 | 270W |
Video game Console | Xbox Series X | 200W |
Video game Console | Xbox 360 | 19SW |
Video game Console | Xbox ONE | 212W |
The calculation may vary according to the make and model of the electronic device.
Scan QR code to download datasheet product
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>