smartbitt 1350VA Automatic Voltage Regulator User Manual
- June 4, 2024
- smartbitt
Table of Contents
smartbitt 1350VA Automatic Voltage Regulator
Important Safe Notice
The total energy load connected to your AVR must not exceed AVRs capacity, an excess in the maximum load capacity will cause the thermal breaker to interrupt the AC flow. (For more details about the load capacity and consumption of your devices please check out the specifications of your devices and/or the consumption table in this manual.) The AVR is designed for its use with devices sensitive to voltage changes, such as PCs, monitors, Inkjet printers, scanners, and faxes, among others. It is also designed for its use with entertainment electronics such as: TVs, gaming consoles, audio, modems, and routers, among others. Is not recommended its use with: freezers, electric tools, air conditioners, dehumidifiers, or any other devices which employ alternating current motors for its functioning. Do not use fuel-powered electric generators or vital support equipment.
WHAT’S IN THE BOX
The contents of the box should include the following elements:
Introduction
Thank you for purchasing Smartbit Products.
This AVR has 8 polarized outlets NEMA5-15R, featuring 3 different kinds of
electronic device protection: Automatic Voltage Regulation, surge protection
and elimination of electrical noise/interferences. This AVR will keep an
optimum voltage level in all its outlets to protect your valuable and delicate
electronic devices such as: PCs, TVs, videogame consoles, and HiFi sound
systems, among others…
Characteristics:
Provides 8 outlets with AVR, surge protection, and electrical noise
protection. Provides stable voltage output through the low voltage step-up
(boost) and high voltage step-down (buck). Accepts wide range of input
voltages. Provides protection for electrical discharge and overload. Provides
telephone line protection through its RJ11 connector
Important Note:
Before installation, please inspect the unit. Make sure that no element contained in the package is damaged. If that is damaged contact the retailer where it was purchased with the responsible manager.
Knowing your AVR
- Power cord
- On/Off Switch
- 8 Outlets (all with surge protection, electrical noise suppression, and AVR).
- Power On LED (Green)
- AVR active (Yellow)*
- Telephone line protection (RJ11 Connector)
- Slotted ventilation
AVR active LED powers on only when the input voltage is above/below normal levels
Installation & Operation
Inspection.
Remove your AVR from the original packaging and verify the integrity of the
device, in case of finding any damage which could have occurred during the
transportation of the device from its origin to the point of sale where it was
acquired, please notify your vendor.
Installation conditions and placement.
Place your AVR in an area free of dirt or excessive dust and which has
adequate airflow. Please place your AVR at least 20 cm away from any other
devices to avoid any interference. Do not block the slotted ventilation. Do
not operate the AVR where the temperature and humidity is above the specified
limits (See specifications table included in this manual). Please operate the
device in an environment free of mechanical vibrations, inflammable gases
and/or corrosive or explosive atmospheres.
First load.
Connect the plug of your AVR into a polarized outlet, it is important that
your current output has an adequate connection to earth ground, this will make
your AVR work properly. Warning! Tearing up or bending the earth ground
terminal from the AVR plug such as inadequate connection could cause electric
shock and will void the warranty immediately.
Important Note
Improper connection can result in risk of electric shock and malfunction of
its equipment, besides this will invalidate your warranty.
Load connection.
This AVR has 8 power outlets NEMA5-15R (American standard) which provide
automatic voltage regulation, surge protection, and electric noise
suppression. Do not exceed the maximum capacity of your AVR, for this purpose,
it’s important for you to take advice from the consumption table further in
this manual to avoid malfunctioning of your devices. For more exactitude on
the consumption of your electronic/electric devices, it’s recommended to see
the consumption of each device, which must be stipulated on the rear panel or
charger of the devices you wish to connect to the AVR.
Modem or telephone line connection.
Connect the telephone line to one of the RJ11 connectors. Connect your
modem/telephone/router into the remaining RJ11 connector. (Only applies for
models with RJ11 protection).
Turning on the AVR.
Once you have connected the devices to the AVR and made sure that the load
doesn’t exceed the capacity of your AVR, now you can proceed to switch the AVR
to the ON position. (I)
Mounting on Wall & Troubleshooting
Installation on a vertical surface.
This AVR can be installed on a vertical surface. There are 2 ways to install
it in this kind of surface, vertically or horizontally
Draw.
Draw with a ruler a 140mm line (Vertical or horizontal depending on your
needs).
Mark.
Mark with a sharp object each of the ends of the drawn line, this is where the
center of the mounting brackets will be.
Place.
In both of the marks place one nail/screw on each, make sure that the
nails/screws are firmly placed and strong enough to support the AVR weight.
Place the AVR mounting brackets over the nails/screws, make sure the AVR is
firmly placed.
Here you will find the most common issues.
If you need any information you can get in contact with our technical support
team via e-mail, telephone or through the webpage http://www.smartbitt.com.
PROBLEM | POSSIBLE CAUSE | ACTION |
---|---|---|
AVR doesn’t turns on. | **AVR is not correctly plugged in to AC power | |
source.** | Make sure the AVR is correctly plugged in to the socket | |
Blown fuse | Check fuse, change if necessary for one of the same value | |
RJ11 not protecting |
The telephone cable not correctly plugged in.
|
Check if the telephone cable is correctly plugged in.
Check if the cable is in operative
conditions.
Technical Specifications
Consumption Table
Phone Mobil Charger | average consumption | 5W |
---|---|---|
Multichannel Amplificator | average consumption | 120W |
Audio Mini component | average consumption | 60W |
Scanner | average consumption | 150W |
Printer | Inkjet Printers | 27W |
PC (monitor) | CRT promedio 17 inches | 70W |
PC (monitor) | LCD, 19 inches | 100W |
PC (monitor) | LCD, 21 inches | 120W |
PC Netbook | 10.1 inches | 40W |
PC Laptop | 15 inches | 65W |
PC Desktop (CPU) | average consumption | 170W |
PC Tower | average consumption | 220W |
PC iMac (CPU) | Apple | 365W |
Radio | average consumption | 15W |
Radio | average consumption Old models | 40W |
Digital Clock | average consumption | 5W |
DVD Player | average consumption | 35W |
VHS Player | average consumption | 100W |
Blu-Ray | average consumption | 60W |
Switch/HUB | 8 Ports | 8W |
Inalambric Phone (Dock) | average consumption | 25W |
TV | CRT Color, 21”, average consumption | 200W |
TV | DLP, 50-56 inches | 206W |
TV | LED, 32 inches | 60W |
TV | LED, 40 inches | 100W |
TV | LED, 55 inches | 190W |
TV | LED, 60 inches | 230W |
TV | LED, 80 inches | 280W |
TV | LCD, 19 inches | 35W |
TV | LCD, 21 inches | 115W |
TV | LCD, 32 inches | 156W |
TV | LCD, 34 inches | 200W |
TV | LCD 37 inches | 236W |
TV | LCD, 42 inches | 322W |
TV | LCD, 50 inches | 464W |
TV | Plasma, 42 inches | 474W |
TV | Plasma, 50-56 inches | 18W |
TV | Nintendo Wii | 34W |
Video game Console | Nintendo Wii U | 23W |
Video game Console | Playstation | 30W |
Video game Console | PS2 | 194W |
Video game Console | PS3 | 137W |
Video game Console | PS4 | 70W |
Video game Console | Xbox | 185W |
Video game Console | Xbox 360 | 112W |
Video game Console | Xbox ONE | 15W |
Video game Console | average consumption | 12W |
Scan QR code to download datasheet product
Documents / Resources
|
smartbitt 1350VA Automatic Voltage
Regulator
[pdf] User Manual
900VA, 1350VA, 2200VA, 1350VA Automatic Voltage Regulator, 1350VA, Automatic
Voltage Regulator
---|---