VECTOR VECLIPS6 733 Watt Lithium Power Station Instruction Manual

VECLIPS4 / VECLIPS6
733 WATT LITHIUM POWER STATION
INSTRUCTION MANUAL

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
© 2022 Baccus Global LLC
Boca Raton, FL 33487
1-877-571-2391

LCD DISPLAY

CONTROL PANEL BUTTONS

1. To activate the unit press the power button for 2 seconds. The display panel will light up and the ventilation fan and icon will activate for 2 seconds and shut down.
2. To switch the unit off press the power button for 2 seconds until the display panel shuts off.
3. The AC icon will light up when the AC button is pressed, and output power and remaining use time will be displayed.
4. will light up to each corresponding feature when activated, output power and remaining use time will be displayed.
5. When multiple ports are being used at the same time, the total output power and remaining use time are displayed.
6. Should a fault occur the fault icon will flash with the corresponding output icon. Immediately shut down that output or it will be automatically shut after 10 seconds. Other outputs will not be affected.

FEATURES

FEATURES

1. Wireless charging pad
2. Strap handle
3. Control panel with touchscreen buttons
4. 12V DC output barrel pin port
5. 12V DC accessory outlet (under protective cover)
6. Dual 120 volt AC outlets (under protective covers)
7. Dual USB-C ports
8. Dual USB-A pods
9. Charging port (charger included)
10. LCD display screen
11. High output LED light

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  FCC Radiation exposure statement. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum 15cm between the radiator and your body.

Changes or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WHAT’S IN THE BOX

Multi-function portable power station|
---|---
USB-C cable|
Instruction manual|
Home charger|

SAFETY GUIDELINES /DEFINITIONS

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation that, if not avoided, may result in property damage.

RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed. The manufacturer strongly recommends that this product NOT be modified and/or used for any application other than for which it was designed. Read and understand all warnings and operating instructions before using any tool or equipment.

READ ALL INSTRUCTIONS

  WARNING: Read all instructions before operating the power station. Failure to follow all the instructions listed below may result in electric shock, fire, and/or serious injury.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

• This unit was designed for household use only.
  WARNING – Risk of fire, electric shock, burst hazard, or injury to persons or property:

• Avoid dangerous environments. Don’t use the power station in damp or wet locations. Don’t use appliances in the rain.

• Keep children away. All visitors should be kept at a distance from the work area.

• Dress properly. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

• Store idle appliances indoors. When not in use, the power station should be stored indoors in a dry and high or locked-up place — out of reach of children.

• Don’t abuse the cord. Never carry the power station by a cord or yank it to disconnect from the receptacle. Keep cord from heat, oil, and sharp edges.

• Disconnect appliances. Disconnect the power station from the power supply when not in use, before servicing, and when changing accessories.

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuits or outlets to be used. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.

• Use of accessories and attachments. The use of any accessory or attachment not recommended for use with this power station could be hazardous. Refer to the accessory section of this manual for further details.

• Stay alert. Use common sense. Do not operate this equipment when you are tired or impaired.

• Check for damaged parts. Any part that is damaged should be replaced by the manufacturer before further use. Do not use the tool if the switch does not turn on and off. Contact the manufacturer at 1-877-571-2391 for more information.

• Do not operate the power station near flammable liquids or in gaseous or explosive atmospheres.

• Never submerge this unit in water; do not expose it to rain, or snow, or use it when wet.

• To reduce the risk of electric shock , disconnect the unit from any power source before attempting maintenance or cleaning. Turning off controls without disconnecting will not reduce this risk,

• Do not use this unit to operate appliances that need more than 10 amps to operate from the 12 Volt DC accessory outlet

• Do not insert foreign objects into the USB port, the 12 Volt DC accessory outlet, or the 120 volt AC outlet.

SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT

• IMPORTANT: This unit is delivered in a partially charged state. Fully charge the unit with an enclosed charging power adapter before using it for the first time.
• To recharge this unit, use only the supplied charging power adapter.
• All Power switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connecting to a power source or load.

BEFORE FIRST USE

• Charge the unit before first use and when battery power is less than 20% to maintain optimal performance and extend service life.
• Each bar on the indicator display indicates the remaining battery level.
• Never completely discharge the internal battery.

CHARGING WITH THE HOME CHARGER

• Connect the DC connector tip to the power station Charging Port, charging will start automatically.
• The Indicator will show you the charging battery level and “Time to Full” on the remaining charge time.
  When fully charged, remove the cable from the unit.

OPTIONAL CHARGING VIA USB-C PD

• The USB-C PD port can be used as a power input or power output port.
• For power output to charge external devices, refer to the section “USB-A & USB-C CHARGING PORTS” below.
• For power input to charge the Power Station via the USB-C PD port, connect the included USB-C cable to a standard 60W or higher USB-C wall adapter. Wall adapter not included.
• Once connected, charging will start automatically.

SOLAR PANEL CHARGING

• Place the solar panel in direct sunlight
• Connect the charging cable, charging will start automatically.
• The Indicator will show you the charging battery level and “Time to Full” on the remaining charge time.
• When fully charged, remove the cable from the unit.

Note. Use only 200 Watt max solar panel with a regulated voltage between 11-30 VDC. The solar panel is not included and is sold separately

SPECIFIC SAFETY INSTRUCTIONS FOR INVERTERS

WARNING – To reduce the risk of electric shock:

• Do not connect to AC distribution wiring.

• Do not make any electrical connections or disconnections in areas designated as IGNITION PROTECTED. This inverter is NOT approved for ignition-protected areas.

• Never immerse the unit in water or any other liquid, or use it when wet.
  WARNING – To reduce the risk of fire:

• Do not operate near flammable materials, fumes, or gases.

• Do not expose to extreme heat or flames.
  CAUTION – To reduce the risk of injury or property damage:

• Disconnect appliance plug from inverter outlet before attempting any repairs to the appliance.

• When an appliance plugged into this unit is used outdoors, use only extension cords intended for use outdoors and so marked.

• Do not attempt to connect the inverter while operating your vehicle. Not paying attention to the road may result in a serious accident.

• Always use the inverter where there is adequate ventilation.

• Always turn the inverter off when not in use.

• Keep in mind that this inverter will not operate high-wattage appliances or equipment that produce heat, such as hair dryers, microwave ovens, and toasters.

• Do not use this inverter with medical devices. It is not tested for medical applications.

• Operate inverter only as described in this Instruction Manual.

120 VOLT AC PORTABLE POWER SUPPLY

The unit is equipped with a 500W pure sine wave inverter to provide power for all suited electronic equipment and electrical appliances.
However, you need to confirm the power rating and socket type of the device to be used. The AC-rated output power of this unit is not more than 500W. Devices such as fans or electric motors require additional power to start (commonly known as the “starting” or “peak” power). The generator can supply a momentary surge in wattage of as high as 1000W for less than 1/10 of a second; however, even devices rated less than the maximum 500W can exceed the inverter’s surge capability and cause an overload automatic shutdown.
Do not use products with more power than the inverter can provide, as this can lead to a risk of instability.
In the event of power overload (with a flashing warning symbol on the LCD screen), the AC output will automatically turn off, a safety feature that prevents the device from damaging the inverter.
If powering more than one device, start one device at a time to avoid power surges and/or inverter overloads. The surge load of each device shall not exceed the inverter’s rated power. You can use an extension cord from the inverter to the device without significantly decreasing the power being generated by the inverter. For best-operating results, the extension cord should be 16 AWG (1.31 mm ) or larger and no longer than 50 feet.

• Connect your AC power supply device or small household appliance to one or more of the unit’s two AC output sockets (make sure the device to be supplied is turned off before inserting the plug into the AC socket).
• Make sure the main power is on, then press the AC button to turn on the AC output, and the corresponding symbol will be displayed on the LCD screen.
• After use, press the AC button again, turn off the AC output of the unit, and pull out the device plug from the AC output socket of the unit.

SPECIFIC SAFETY INSTRUCTIONS FOR THE USB-A S USB-C PORTS

• Do not insert foreign objects into the USB Port.
• Do not attach USB hubs or more than one personal electronic device to the USB Port.
• Some household USB-powered electronics will not operate with this unit.

USB-A S USB-C CHARGING PORTS

Insert the input end of the device cable into the USB-A port or Type-C port of the unit. First, make sure that the main power is on. Then press the USB button on the control panel to turn on the output, and the corresponding symbol  will be displayed on the LCD screen.
After charging is completed, press the USB button again to turn off the output of the unit, and pull the wiring plug from the USB-A or Type-C output port of the machine.
The USB power port remains on until the USB power button is pressed again to turn it off. Make sure the USB port is turned off when the unit is being recharged or stored.

Periodically check the unit’s Battery Status on the backlit LCD screen.
Note: This unit’s USB power ort does not support data communication.
Note: The USB-C symbol only appears on the LCD screen when the device cable is inserted into the 60W PD port.

WIRELESS CHARGING

The built-in Wireless Charging feature is suitable for most appliances with a Wireless Charging function.
Before proceeding, check the unit’s battery status on the LCD screen. When the battery level is nearly empty with only one solid bar, the unit MUST be recharged before use or the unit’s built-in low voltage protection will activate. The empty Battery Status Icon will flash for a short period of time before automatic shut down.

WIRELESS OUTPUT
Press the wireless button to activate standby mode.
Flashes slowly
Solid during charging
****Quick flashing when a fault is detected

IMPORTANT:

• Make sure the Wireless Charging function is turned off when the unit is being recharged or stored.
• Note: Wireless charging may not work with some devices that are not Qi-certified. Wireless charging is available with some compatible Qi-certified devices up to 10W. For other devices, slower charging rates will apply. Actual charging speed may vary depending on multiple factors such as battery condition and frequency of use.

SPECIFIC SAFETY INSTRUCTIONS FOR THE 12V DC OUTPUT

• Do not insert foreign objects into the 12VDC output port.
• Do not attach more than one personal electronic device to the 12VDC output pods.
• Some household-powered electronics will not operate with this unit.

12 VOLT DC PORTABLE POWER SUPPLY WITH A COMBINED 10A OUTPUT

DC 5.5 output port:
Insert the 12V DC plug into the DC output port of the machine, first, make sure that the main power is turned on, then press the DC button to turn on the 12V DC output. At the same time, the corresponding symbol is displayed on the LCD screen.
12V DC accessory output port:
Insert the 12V DC accessory plug into the DC accessory socket of the unit, first make sure that the main power is turned on, then press the DC button to turn on the 12V DC output. At the same time, the corresponding symbol is displayed on the LCD screen.
After charging is completed, press the DC button again, turn off the 12V DC output of the unit, and pull out the 12V DC accessory plug from the 12V DC accessory socket of the unit.
IMPORTANT: always check the correct polarity of the device prior to accessing 12-volt dc outlet. LED AREA LIGHT

The built-in high-intensity area light is controlled by the area light power button on the control panel (refer to the Features section to locate). Make sure that the main power is on, then press the LED button to turn on the lighting function and display the corresponding symbol on the LCD screen.

1. Press the light button a second time to activate the light at 50% capacity.
2. Press the light button a third time to switch to SOS mode.
3. Press the light button a fourth time to switch the light off.
   Make sure the area light and the unit are turned off when the unit is being recharged or stored.

SAVE THESE INSTRUCTIONS

OVERVIEW
LCD Warning Symbols

Flashing once per second, the unit will go to sleep after 10 seconds.| Cause:
Charging fault (high & low temperature protection).
Solution:
Unplug the charger, after the battery temperature returns to normal, reconnect the charger for charging the unit.
---|---
Flashing once per second, the unit will go to sleep after 10 seconds. **| Cause:
Discharge high-temperature protection.
Solution:
After the battery temperature returns to normal press the main power button to restore.
Flashing once second, unit down after per will shut- 10 seconds
**| Cause:
DC output fault (over-current or short circuit protection).
Solution:
Press the DC button to restore after the load is removed.
DC Flashing once second, unit down after (,1 per will shut- 10 seconds
**| Cause:
USB-A output fault (over-current or short circuit protection). Solution:
Press the USB-A button to restore after the load is removed.
Flashing once second, unit down after per will shut- 10 seconds
**| Cause:
AC output fault (overload or short circuit protection).
Solution:
Press the AC button to restore after the load is removed.
 Flashing once second, unit down after 1 per will shut- 10 seconds
**| Cause:
USB-C output fault (over-current or short circuit protection). Solution:**
After the fault is removed, re-plug and restore the output.

Note: The unit will automatically power off once ALL the functions are turned off.

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors, and wires. Contact manufacturer to replace any components that have become worn or broken.

Battery

Please be advised that the battery is designed to last the service life of the unit and is not replaceable, removable, or serviceable. Service life is dependent on a number of factors including but not limited to the number of recharge cycles, and proper care and maintenance of the battery by the end- user. Contact the manufacturer for any information you may need.

SAFE BATTERY DISPOSAL

Contains a lithium battery, which must be disposed of properly. Recycling is required. Failure to comply with local, state, and federal regulations can result in fines or imprisonment.

Please recycle.
WARNINGS:

• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose the battery to fire or intense heat as it may explode.

TROUBLESHOOTING

Unit not charging|

•  Make sure all of the unit’s functions are turned off.
• Check the connection to the AC power source.
• Confirm there is a functioning AC current.

---|---
The wireless charging function will not charge the appliance|

• Make sure the Wireless Charging Button has been pressed to turn the Wireless Charging function on.
• Make sure the appliance is placed in the center of the Wireless Charging Pad.
• Some appliances may not charge/operate with this unit. Check the manual of the corresponding appliance to confirm that it can be used with this type of wireless charging.
• Check that the unit has a full charge. Recharge the unit if necessary.

USB Power Port will not power the appliance|

• Make sure the USB Power has been pressed to turn the USB function ON.
• If a fault condition exists in one of the USB Ports, the Fault Indicator will flash. Refer to the LCD Warning Symbols section in the “USB’ section to remedy any faults.
• Some USB-powered household electronics will not operate with this USB charging/power port. Check the manual of the corresponding electronic device to confirm that it can be used with this type of USB charging/power port.
• Check that the unit has a full charge. Recharge the unit if necessary.

120 Volt AC outlet will not power appliance|

• Make sure the AC Power Button has been turned on.
• Make sure you have followed all the steps in the “120 AC Power Outlet” section carefully. Refer to the important notes included in that section that explain common problems and solutions.
• Make sure the combined draw of the appliance being powered is not more than 500 watts.
• Check that unit has a full charge. Recharge unit if necessary.

Use of photovoltaic solar panel charging fault|

• If an over-current occurs. make sure to use solar panels of recommended specifications.
• If there is weak sunlight. place the solar panels in direct sunlight (Do not expose the unit to the hot sun).
• If the wire harness connection is abnormal, reconnect wiring hardness. If the problem persists, replace the solar panels.

LED area light does not come ON|

• Make sure the area light power button has been pressed to turn the area light on.
• Check that unit has a full charge. Recharge unit if necessary.

---|---

ACCESSORIES

Recommended accessories for use with your unit may be available from the manufacturer. If you need assistance regarding accessories, please contact the manufacturer at 1-877-571-2391.

WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.

SERVICE INFORMATION

Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391.

FULL TWO-YEAR LIMITED HOME USE WARRANTY

The manufacturer warrants this product against defects in materials and workmanship for a period of TWO (2) YEARS from the date of retail purchase by the original end-user purchaser (“Warranty Period”).

If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways:

• Return the product to the manufacturer for repair or replacement at the manufacturer’s option. Proof of purchase may be required by the manufacturer.
• Return the product to the retailer where the product was purchased for an exchange (provided that the store is a participating retailer). Returns to the retailer should be made within the time period of the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

This warranty does not apply to accessories, bulbs, fuses, and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from state to state or province to province. This product is not intended for commercial use.

Please visit our website www.baccusglobal.com/register to register your new Baccus Global LLC product and to be kept up to date on new products and special offers.

SPECIFICATIONS

Charging
LED| 10W MAX
10W MAX

FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body: Use only the supplied antenna. FCC ID: 2AZ48-VECLIPS6

Imported by Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.baccusglobal.com 1-877-571-2391
RD041322

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>