SOUNDPEATS TM194 TrueFree2 WS Sports Wireless Earbuds User Manual

soundpeats TM194 TrueFree2 WS Sports Wireless Earbuds

Package ContentSpecifications

Product Diagram

Touch Control

Wearing the earbuds

1. Identify the lef and right earbuds.
2. Rotate the earbuds, and adjust to the best angle.
3. Make Sure the ear fins fit your cymbal conchae.
4. Make sure the ear tip seals in the ear cancel.

Getting Started

Pairing &Re-pairing

1. Take both earbuds out of the charging case while the case is with enough power left. The left and right earbuds will pair to each other at first with a prompt suggests Successfully connected. After this, the LED on the left earbud stays on, and right earbud LED fiashes in red and white alternately with a voice prompt “Pairing” indicating the earbuds enter pairing mode
2. “SOUNDPEATS TrueFree 2” wll show up on the Bluetooth list, click it to connect.You will hear oa voice prompt “connected” from right earbud when the earbuds connect with your device suCcEssfully.
3. soundpeats TrueFree 2 Bluetooth earbuds can remember previously pired devices. When you make the second connection, simply activate the Bluetooth in your device. take out both earbuds from the charging case. They will connect to each other, and reconnect to your device automatically. If the earbuds dont automatically connect to your device, please activate the Bluetooth in your device and hit “SOUNDPEATS TrueFree 2” on the Bluetooth list.
4. Mono mode: after SOUNDPEATS TrueFree 2 is paired successfully, both the left earbud and the right earbud can be used separately.

Note

If you want to change the pairing device in the connection status, you can have it enter pairing mode direcily just by a long press for the multifunction button for 5s when the headset is off.

Reset Try

the following steps to reset if you fail to build a connection between fwo earbuds or between earbuds and the device:

1. Clear pairing record between the earbuds and all your devices.
2. Place back both earbuds into the charging case and ensure they’re in charging status. Then long-press the multifunction button of both earbuds for 10s unti the LED light of both earbuds fiash white twice. Reset is complete

Charging

soundpeats TrueFree 2 Bluetooth earbuds are equipped with a charging case which is not only a charging dock to charge the earbuds, but also a carrying case. With a built-in rechargeable battery, the charging case can provide 4 times full charge for the earbuds (both lef and right).

Charging the earbuds

The earbuds are partially charged at the factory. Please make sure they are fully charged before first use.

1. Put the earbuds into corresponding charging docks, make sure the charging contactors are match.
2. The LED indlicator will turn red when it starts charging.
3. The red LED indicator will turn off when the earbuds are fully charged.

Charging the case

When the charging case is in low battery level the last white led indicator flashes, please recharge the case:

1. Connect the charging port with Type-C charging adapter or computer Type-C port(current less than 5V 1A)
2. Please charge the earbuds at least once every 3 months when not in use for a long flame.

Warranty

We warranY this device 12 MONTHS from dafe of the original purchase for manufacture defects

support@soundpeatsaudio.com www.soundpeatsaudio.com

Please scan QR code to know the PDF user manual. https://soundpeatsaudio.com/downloads/

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installead and used in accordance with the instructions, may Cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which Can be determined by furning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>