DYNOJET PC6-20012 Power Commander 6 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-20012
Model Coverage: 2008-2009 Suzuki GSX650F 2007-2008 Suzuki GSF650
PC6-20012 Power Commander 6
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS| 2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
1 POSI-TAP
---|---
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
IPC6-20012.01
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
set up you can alter your map based on gear position and setup gear-dependent
kill times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2 2008-2009 SUZUKI GSX650F, 2007-2008 SUZUKI GSF650
INSTALLATION GUIDE
INSTALLING THE POWER COMMANDER 6
-
Remove the seat and left-hand side cover.
-
Remove the fuel tank.
-
Lay the PC6 in the tail section.
-
Route the wiring harness from the PC6 under the frame crossover and go towards the engine along the right-hand side of the air box.
-
Unplug the stock wiring harness from each of the fuel injectors.
-
Plug the connectors from the PC6 in-line of the stock injectors and the stock wiring harness.
PC6 colors: BLUE – cylinder #1
GREEN – cylinder #2
YELLOW – cylinder #3
ORANGE – cylinder #4 -
Locate the Throttle Position Sensor which is located on the left-hand side of the throttle bodies.
This is the 5-pin connector.
-
Attach the supplied Posi- tap to the stock PINK/ BLACK wire of the TPS.
-
Plug the GREY wire from the PC6 into the wiretap.
It is recommended to use dielectric grease on these connections.
For a cleaner look, you can follow the TPS wire back to a junction where you can hide the wiretap easier. -
Attach the ground wire from the PC6 to the negative side of the battery.
-
Using the supplied Velcro, install the PC6 in the tail section to the inner fender.
Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive. -
Reinstall the fuel tank, side cover, and seat. Download the latest map files from our website at dynojet.com/tunes.
4 2008-2009 SUZUKI GSX650F, 2007-2008 SUZUKI GSF650
PUSH THE LIMIT
PC6-20012
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –
800-992-4993 –
DYNOJET.COM
© 2007-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>