milwaukee PFH 26 Hammer Drill Instruction Manual
- June 3, 2024
- Milwaukee
Table of Contents
milwaukee PFH 26 Hammer Drill Instruction Manual
Illustrations
TECHNICAL DATA
| PFH 26| PH 26
---|---|---
Production code| 4282 31 02| 4282 41 02
| 4290 11 02
| 4290 16 02
000001-999999| 000001-999999
Rated input| 725 W| 725 W
Output| 365 W| 365 W
No-load speed| 1500 min-1| 1500 min-1
Speed under load max| 1250 min-1| 1250 min-1
Rate of percussion under load max| 4500 min-1| 4500 min-1
Impact energy per stroke according to EPTA-Procedure 05/2009| 2,4 J| 2,4 J
Drilling capacity in concrete| 26 mm| 26 mm
Drilling capacity in stee| 13 mm| 13 mm
Drilling capacity in wood| 30 mm| 30 mm
Light core cutter in bricks and limestone| 50 mm| 50 mm
Chuck neck diameter| 43 mm| .43 mm
Weight according EPTA-Procedure 01/2003| 2,4 kg| 2,4 kg
Noise Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)): 92 dB (A) : 92 dB (A)
Sound power level (Uncertainty K=3dB(A)): 103 dB (A) : 103 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value ah:
Hammer-drilling in concrete: 13,5 m/s²: 13,5 m/s²
Uncertainty K = 1,5 m/s²: 1,5 m/s²
Chiselling: – m/s²: 11,2 m/s²
Uncertainty K = – m/s²: 1,5 m/s²
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future reference.
ROTARY HAMMER SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
Hold the power tool by insulated gripping surfaces only, when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force. Determine
why the insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be machined
- the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
- when changing tools
- when setting the device down
Chips and splinters must not be removed while the machine is running.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Always disconnect the plug from the socket before carrying out any work on the machine.
When working with large drill diameters, the auxiliary handle
must be fastened in a right angle with the main handle (see
illustrations, section “Twisting the handle”).
SPECIFIED CONDITIONS OF USE
PFH 26: The rotary pneumatic hammer can be used for
hammer drilling and drilling in wood, metal as well as plastic.
PH 26: The rotary pneumatic hammer can be used for
hammer drilling, chiselling in stone and concrete and drilling
in wood, metal as well as plastic.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under “Technical Data” fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-6:2010
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2016-03-29
Alexander Krug
Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Appliances used at many different locations including wet room and open air must be connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Connect only to single-phase AC current and only to the system voltage indicated on the rating plate. It is also possible to connect to sockets without an earthing contact as the design conforms to safety class II.
Make sure the machine is switched off before plugging in.
This is a device for professional use which may slightly exceed the guide values for current harmonics when it is connected to the public low voltage mains supply. You should therefore contact your energy supply company before you connect the device to the public low voltage mains supply.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Important note! If the carbon brushes are worn, in addition to exchanging the brushes the tool should be sent to after-sales service. This will ensure long service life and top performance.
If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, to avoid hazardous situations.
Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying out any work on the machine.
Please read the instructions carefully before starting the machine.
Accessory – Not included in standard equipment, available as an accessory.
Do not dispose of electric tools together with household waste material.
Electric tools and electronic equipment that have reached the end of their
life must be collected separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for recycling advice and
collection point.
Class II tool, tool in which protection against electric shock does not rely
on basic insulation only, but in which additional safety precautions, such as
double insulation or reinforced insulation, are provided.
There being no provision for protective earthing or reliance upon installation
conditions.
European Conformity Mark
EurAsian Conformity Mark.
Copyright 2016
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
+49 (0) 7195-12-0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>