Einhell TC-CD 18/35 Li Cordless Drill/Screwdriver Instruction Manual
- June 5, 2024
- Einhell
Table of Contents
Einhell TC-CD 18/35 Li Cordless Drill/Screwdriver
Parts
Danger!
When using the equipment, a few safety precautions must be observed to avoid
injuries and damage. Please read the complete operating instructions and
safety regulations with due care. Keep this manual in a safe place, so that
the information is available at all times. If you give the equipment to any
other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due
to a failure to follow these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 8)
- Danger! – Read the operating instructions to reduce the risk of injury.
- Caution! Wear ear-muffs. The impact of noise can cause damage to hearing.
- Caution! Wear a breathing mask. Dust that is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
- Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of sight.
- Store the batteries only in dry rooms with an ambient temperature of +10°C to +40°C. Place only fully charged batteries in storage (charged at least 40%).
- Safety class II
- For use in dry rooms only.
Safety regulations
The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations and technical
data provided on or with this power tool. Failure to adhere to the following
instructions may result in electric shock, fi re and/or serious injury. Keep
all the safety information and instructions in a safe place for future use.
Layout and items supplied
-
Torque selector
-
Battery capacity indicator
-
Changeover switch
-
ON/OFF switch
-
Battery pack
-
Battery charger
-
Pushlock button
-
Quick-change drill chuck
-
LED lamp
-
Items supplied
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase atthe latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions. -
Open the packaging and take out the equipment with care.
-
Remove the packaging material and any packaging and/or transportation braces (if available).
-
Check to see if all items are supplied.
-
Inspect the equipment and accessories for transport damage.
-
If possible, please keep the packaging until the end of the guarantee period.
Important!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating! -
Cordless drill/screwdriver
-
Battery pack
-
Battery charger
-
Original operating instructions
-
Safety instructions
Proper use
The cordless drill driver is designed for tightening and undoing screws in wood, as well as for drilling in wood, metal and plastic. The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
Technical data
- Voltage supply ………………………………….18 V d.c.
- Idling speed: …………………………………. 0-550 rpm
- Torque settings: ……………………………………. 21+1
- Forward and reverse rotation ……………………..yes
- Chuck clamping width ……………………. 0,8-10 mm
- Battery charger output voltage: . ………… 20 V d. c.
- Battery charger output current: ………………….. 3 A
- Mains voltage for charger: .. 200-250V~ 50-60 Hz
- Battery type: … ………………………………Lithium-ion
- Number of battery cells: . ………………………… 5/10
- Battery capacitance: ………………….1.5 Ah/3,0 Ah
- Weight ……………………………………………….1.35 kg
- Max. screw diameter: . …………………………… 6 mm
The maximum screw diameter indicates the maximum diameter of the screw that can be screwed into wood. The screw diameter can vary depending on the type of wood. Keep the noise emissions and vibrations to a minimum.
-
Only use appliances that are in perfect working order.
-
Service and clean the appliance regularly.
-
Adapt your working style to suit the appliance.
-
Do not overload the appliance.
-
Have the appliance serviced whenever necessary?
-
Switch the appliance off when it is not in use.
Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout: -
Lung damage if no suitable protective dust mask is used.
-
Damage to hearing if no suitable ear protection is used.
-
Health damage is caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.
Limit the operating time.
All stages of the operating cycle must be considered (for example, times in which the electric tools are switched off and times in which the tool is switched on but operates without load).
Before starting the equipment
- Be sure to read the following information before you use your cordless screwdriver for the fi rst time:
- Charge the battery pack with the charger supplied.
- Only ever use sharp drill bits and screwdriver bits that are suitable for the purpose and in faultless condition.
- Always check for concealed electric cables and gas and water pipes when drilling and screwing in walls.
Operation
Charging the LI battery pack
-
Remove the battery pack (5) from the handle, pressing the pushlock buttons (7) downwards to do so.
-
Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (6) into the mains socket outlet. The green LED will then begin to fl ash.
-
Push the battery pack onto the battery charger. In section 10 “Charger indicator” you will fi nd a table with an explanation of the LED indicator on the charger. If the battery pack fails to become charged, please check
-
whether there is voltage at the socket-outlet
-
whether there is proper contact at the charging contacts on the charger.
If the battery still fails to become charged, please return -
the charger
-
the battery pack
to our Customer Service Department. To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased. When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fi res. To ensure that the battery pack provides long service, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops. Never allow the battery pack to become fully discharged. This will cause it to develop a defect. -
Torque setting (Fig. 4/Item 1) Caution! Only ever adjust the setting ring when the equipment is at a standstill. The cordless screwdriver is fi tted with a mechanical torque selector. The torque for a particular screw size is set with the setting ring (1). The torque is dependent on a number of factors:
-
On the type and hardness of the material involved
-
On the type and length of the screws used
-
On the requirements that the screw connection has to satisfy
The grating disengagement of the coupling indicates that the selected torque level has been reached. -
Drilling (Fig. 4/Item 1) For drilling purposes, adjust the setting ring for the torque to the last setting “Drill”. In the drill setting the slip coupling is non-functional. The maximum torque is available for drilling.
-
Changeover switch (Fig. 5/Item 3) The slide switch above the On/Off switch is for setting the direction of rotation of the cordless screwdriver and for preventing the cordless screwdriver from being switched on inadvertently. You can select between clockwise and counterclockwise rotation. To avoid causing damage to the gearing, the direction of rotation must only be changed when the equipment is at a standstill. When the slide switch is in the middle position, the On/Off switch is blocked.
-
On/Off switch (Fig. 5/Item 4) Infi nitely variable speed control is possible with the On/Off switch. The further you push the switch, the higher the speed of the cordless screwdriver.
-
All LEDs blink: The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.
-
LED lamp
The LED lamp (9) can be used in poor lighting conditions to illuminate the area where you want to drill or screw. The LED lamp (9) will be lit automatically as soon as you press the ON/off switch (4). -
Changing the tool is Important. Set the changeover switch (3) to its centre position whenever you carry out any work (for example changing the tool, maintenance work, etc.) on the cordless screwdriver.
-
Open the chuck (8). The chuck opening (a) must be large enough to hold the tool (drill bit or screwdriver bit).
-
Select the suitable tool. Push the tool as far as possible into the chuck opening (a).
-
Tighten the chuck (8) and then check that the tool is secure.
-
Screwdriving
It is advisable to use self-centering screws (e.g. cross recessed head) as these will enable you to work safely and reliably. Always make sure that the bit used is of the same size and shape as the screw. Set the torque to suit the screw size as specifi ed in the instructions.
Cleaning, maintenance
Cleaning
- Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- We recommend that you clean the device immediately each time you have finished using it.
- Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.
Maintenance
There are no parts inside the equipment which require additional maintenance.
Ordering spare parts and accessories Please provide the following information
when ordering spare parts:
- Type of unit
- Article number of the unit
- ID number of the unit
- Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in
transit. The raw materials in this packaging can be reused or recycled. The
equipment and its accessories are made of various types of material, such as
metal and plastic. Never place defective equipment in your household refuse.
The equipment should be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of such a collection point, you
should ask in your local council offi ces.
Charger indicator
| Indicator status | Explanations and actions |
|---|---|
| Red LED | Green LED |
| Off | Flashing |
The charger is connected to the mains and is ready for use; there is no battery pack in the charger
On| Off| Charging
The charger is charging the battery pack in quick charge mode. The char- ging times are shown directly on the charger.
Important! The actual charging times may vary slightly from the stated
charging times depending on the existing battery charge.
Off| On| The battery is charged and ready for use. (READY TO GO)
The unit then changes over to gentle charging mode until the battery is fully charged.
To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.
Action:
Take the battery pack out of the charger. Disconnect the charger from the mains supply.
Flashing| Off| Adapted charging
The charger is in gentle charging mode.
For safety reasons the charging is performed less quickly and takes more time. The reasons can be:
– The rechargeable battery has not been used for a very long time.
– The battery temperature is outside the ideal range.
Action:
Wait for the charging to be completed; you can still continue to charge the battery pack.
Flashing| Flashing| Fault
Charging is no longer possible. The battery pack is defective.
Action:
Never charge a defective battery pack. Take the battery pack out of the charger.
On| On| Temperature fault
The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).
Action:
Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .
Service information
We have competent service partners in all countries named on the guarantee
certificate whose contact details can also be found on the guarantee certifi
cate. These partners will help you with all service requests such as repairs,
spare and wearing part orders or the purchase of consumables. Please note that
the following parts of this product are subject to normal or natural wear and
that the following parts are therefore also required for use as consumables.
| Category | Example |
|---|---|
| Wear parts* | Drill chuck, Battery |
| Consumables* | Bit inserts/drill bits |
| Missing parts |
In the eff ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:
- Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure?
- What malfunction does the equipment have in your opinion (main symptom)?
- Describe this malfunction.
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:
- These guarantee terms apply to consumers only, e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
- The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectification of said defects on the product or the replacement of the product, whichever we
Please note that our devices are not designed for use in commercial, trade or professional applica- tions. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
- The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex- posing the device to abnormal environmental conditions or by lack of care and
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for ex- ample by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the
- The guarantee is valid for a period of 24 months starting from the purchase date of the Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if on-site service is used.
- To make a claim under the guarantee, please register the defective device at:
www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is co- vered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.
References
- Einhell Service
- VICE - VICE is the definitive guide to enlightening information.
- Einhell Service
- kwb Germany GmbH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>