MAXI-COSI SW14107 Cabriofix i-Size Baby Car Seat User Guide
- June 5, 2024
- MAXI-COSI
Table of Contents
MAXI-COSI SW14107 Cabriofix i-Size Baby Car Seat
The quick start guide is intended to provide only an overview. For the maximum protection and comfort of your child, it is essential that you read through the entire manual carefully and follow all instructions.
In The Box
Quick start guide
This is an Enhanced Infant Carrier Module to be used in combination with
i-Size product approved according to Regulation No. 129, for use in, “i-Size
compatible” vehicle seating positions as indicated by vehicle manufacturers in
the vehicle user’s manual. This module could also be used as a stand-alone
infant carrier according to the instructions of the Enhanced Child Restraint
System manufacturer. If in doubt, consult either the manufacturer or the
retailer of the Enhanced Child Restraint System.
Category of your car seat: i-Size infant carrier module (40-75 cm – up to
approx. 12 months)
Position of your car seat: rearward facing
How To Fix Seat position in the cars
CabrioFix i-Size can be installed on a Maxi-Cosi ISOFIX base. Please make sure
you read the user manual of this base carefully.
Alternatively, the CabrioFix i-Size can be installed by using the 3-point
safety belt of your car.
This child restraint is classified for “Universal” use and is suitable for
fixing
into the seat position of the following cars:
IMPORTANT :
For a complete list of cars, please visit www.maxi-cosi.com/car-fitting-
list
Instruction for use
Carrying handle
- A1: Carrying and driving position
- A2: Release and installation position for child
- A3: Reclined cradle position
Ready to go
How to fix on car seat
Child installation
Stroller & car seat
Washing
A – Carrying handle
B – Sun canopy
C – Push button for carrying handle
adjustment (L+R)
D – Belt hooks for lap part of belt (L+R)
E – Harness adjuster button
F – Instruction manual storage
G – Harness belt tensioner strap
H – Belt buckle with belt pad
I – Cover
J – Shoulder belts with removable belt pads K – Newborn inlay
L – Stroller release buttons (L+R)
M – Headrest
N1 – Belt hook for shoulder part of belt N2 – Mounting bars for base
SAFETY
The car seat is developed for intensive use of approximately 6 years.
CabrioFix i-Size car use
- Only use a forward-facing seat that is fitted with a 3-point safety belt that complies with the ECE R16 standard.
- Make sure the car safety belt buckle runs in a straight line and stays below the belt hook of the car seat.
- The car safety belt must be threaded tight along with all blue markings. For a proper installation, check the instruction in this manual and the sticker on the side of the car seat.
WARNING:
Install the car seat only rearward-facing in the car on a forward-facing
vehicle seat.
CabrioFix i-Size and your baby
-
Make sure you can fit no more than one finger between the harness and your baby (1cm).
If there is more space than 1 cm, tighten the harness belt further. -
Only use the baby-hugg inlay of the CabrioFix i-Size until your baby exceeds the 60 cm length limit. Afterward, remove the baby-hugg inlay from the CabrioFix i-Size.
WARNING:
- Never place the car seat on an elevated surface (such as a table or chair).
- In order to prevent the car seat from tipping over during carrying, check if the carrying handle is locked place in the carrying position (A1).
- When CabrioFix i-Size is installed on a stroller, always make sure to use approved car seat adapters and to secure CabrioFix i-Size correctly.
Care
The cover, inlay, belt pads and sun canopy of the car seat can be removed for washing. The front baleen of the sun canopy needs to be removed before washing.
References
- Car Seats & Baby Gear | Safety 1st, Maxi-Cosi, Cosco Kids, Tiny Love – Dorel Juvenile
- Car seat Advisory Tool | Maxi-Cosi
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>