Skullcandy Indy XT ANC – Active Noise Canceling True Wireless Earbuds-Complete Features/Instruction Manual

Skullcandy Indy XT ANC – Active Noise Canceling True Wireless Earbuds

Specifications

• SPEAKER DRIVER: 6mm
• IMPEDANCE: 16 Ohms, THD <3%@1KHz
• VOLTAGE REGULATION: 5V, 500mA
• BLUETOOTH : 5.0
• FREQUENCY BAND: 2402MHz – 2480MHz
• MAXIMUM POWER: <9dBm
• WEIGHT: 59.5g

Introduction

With Active Noise Cancelling, the Indy XT is a truly wireless earbud that cuts through the noise. Through a brief audio test on Skullcandy, you may fine-tune them to your specific hearing. The technology changes audio levels automatically, allowing you to hear your music like you’ve never heard it before. If you need to get back to reality, Ambient Mode allows you to listen to your surroundings in real time so you don’t miss anything. Also, don’t be concerned about misplacing your earbuds. Tile locating technology is included into the Indy XT ANC. Rapid Charge allows you to listen for 3 hours in just 10 minutes of charging time, and up to 19 hours on a full charge. With an IPX4 water and dust resistance rating, the Indy XT ANC is ready for any adventure.

How to power ON

How to power OFF

How to charge the charging case

• Use CTYPE cable to charge the charging case.

How to charge the earbuds

• Place the earbuds into the charging case the earbuds will start charging.

How to pair

• To enter the pairing mode, press the earbud for 4 seconds.
• Your earbuds will be ready to pair.

Pairing a new device

How to power on the earbuds

How to power off the earbuds

FUNCTIONS

• Click on the right earbud twice to play or pause the music.

• To change the track press right earbud for 2 seconds.

• Press left earbud for 2 seconds your previous track will be played.
  

• Tap right earbud for one time to volume up.

• Tap left earbud for one time to volume down.

• To answer or decline the call, press the right earbud two times.

• To reset the earbuds, press both earbuds for 4 seconds.

• Your earbuds will be reset.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

ISED Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED SAR Compliance Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is reported under this standard during product certification for use when properly worn on the body. This equipment should be installed and operated with a minimum distance 0cm between the radiator and your body.

Frequently Asked Questions

• In Skullcandy Indy, how can I change modes?
  When you tap the LEFT or RIGHT bud 2x and hold for 2 seconds while they are paired, you will hear a voice prompt telling you when it changes to a new pre- set EQ. Each time you complete the touch 2x and hold for 2 seconds action, the EQ modes will cycle through.\ When your

• Skullcandy case is fully charged, how do you know?
  Place your earbuds in the charging case to charge them. While charging, the earbud LEDs will be solid red. When the LEDs are fully charged, they will turn off.

• On Indy ANC, how do I turn off noise cancellation?
  Tap either bud once and then quickly touch the same bud for 2 seconds to toggle/alternate between your ANC ON/OFF and Ambient Modes.

• How can I increase the volume of my Skullcandy?
  Many customers have discovered that lowering the volume by gently touching your headphones until they reach the lowest possible volume, then repeating the process with the other earbuds by slowly tapping to increase the volume, addressed the problem.

• How loud are Skullcandy earbuds?
  Almost all of their headphones have the ability to get really loud and bassy. While the Sesh don’t have as much bass as the Crusher, they do have amplified bass that comes through after you get a good fit.

• What does the Skullcandy push case’s button do?
  A button on the front of the case displays the charge state with four LEDs next to it. They also flicker while charging the case. A micro USB port on the back charges the case, which then charges the earphones within.

• What’s the deal with my Skullcandy case blinking?
  Open the lid to see how much battery life is left in the case; the solitary LED on the front of the case will flash to indicate the charge level. Each LED flash symbolizes a different level of charge: low, medium, and high.

• What is the best way to tell if my Skullcandy earbuds are charged?
  The earbuds’ LEDs will glow solid red once placed in the case, signaling that they are charging; after fully charged, they will automatically stop charging and the LED light will switch off

• Why does one of my Skullcandy wireless earphones work but not the other?
  In most circumstances, if your left or right Skullcandy earbuds aren’t working, it’s because they didn’t pair with each other. Turn both earphones off, then hold the button on one of them for 10 seconds before putting it in the case. Replace the second earbud and repeat the process.

• My Skullcandy Bluetooth earphones aren’t connecting to each other.
  Ascertain that the two devices are in close enough proximity. It’s probably worth mentioning that any devices you’re trying to link should be within five feet of each other. Turn the devices off and on again. A gentle reset can occasionally fix a problem.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>