Gerlach GL 7733 Tower Heater LCD with Humidifier User Manual
- June 5, 2024
- Gerlach
Table of Contents
Gerlach GL 7733 Tower Heater LCD with Humidifier User Manual
user manual
This product is suitable only for occasional use or for use in well insulated rooms.
GENERAL SAFETY CONDITIONS
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
-
Before using the device, read the operating instructions and follow the instructions contained therein. The manufacturer is not liable for any damage caused by using the device contrary to its intended use or improper operation.
-
The appliance is for home use only. Do not use for other purposes not in accordance with its intended use.
-
The device should be connected to 220-240V ~ 50 / 60Hz. In order to increase the safety of use, many electrical devices should not be connected to one electric circuit simultaneously.
-
Be especially careful when using the device when children are in the vicinity. Do not allow children to play with the device and do not let children or people unfamiliar with the device use it.
-
WARNING: This equipment may be used by children over 8 years of age and people with reduced physical, sensory or mental abilities, or people with no experience or knowledge of the equipment, if this is done under the supervision of a person responsible for their safety or has been provided to them instructions on the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and user maintenance should not be performed by children, unless they are over 8 years old and these activities are performed under supervision.
-
Always after use, remove the plug from the outlet by holding the outlet with your hand. DO NOT pull on the cord.
-
Do not immerse the cable, plug and the entire device in water or any other liquid. Do not expose the device to weather conditions (rain, sun, etc.) or use it in high humidity conditions (bathrooms, damp mobile homes).
-
Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair shop in order to avoid a hazard.
-
Do not use the appliance if the power cord is damaged or if it has been dropped or damaged in any way or if it is not working properly. Do not repair the device yourself as it may cause electric shock. Take the damaged device to an appropriate service center for inspection or repair. Any repairs may only be performed by authorized service points. Incorrectly performed repairs can pose a serious threat to the user.
-
Place the device on a cool, stable, even surface, away from heating appliances such as: electric stove, gas burner, etc.
-
Do not use the device near flammable materials.
-
For additional protection, it is advisable to install a residual current device (RCD) in the electrical circuit with a rated residual current not exceeding 30 mA. In this regard, please consult a specialist electrician.
-
When the device is used in the bathroom, remove the plug from the socket after use, as the proximity of water is a hazard even when the device is turned off.
-
Do not put your fingers or any objects or metal foreign objects inside the product, through the ventilation grille and other slots, otherwise it may cause electric shock or malfunction.
-
Do not put any objects on top of the device. Vents must not be covered by a towel, curtain, etc. It may damage the device or cause a fire.
-
The device heats up during operation, do not touch hot parts of the device. Do not touch the device with wet hands.
-
If the convector gets wet or any object falls through the convector ventilation grille, turn it off immediately and disconnect it from the mains. Before relaunching using the convector, contact the service.
-
Do not place the machine directly below an electrical socket.
-
Always switch the device off using the buttons before disconnecting it from the mains.
-
Do not use this device if it has been dropped.
-
Do not use if there are visible signs of damage to the device.
-
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer.
-
All items should be at least 1 meter from the front and sides of the device.
-
Do not insert or allow foreign objects to enter the ventilation or exhaust vents as this may result in electric shock, fire or damage to the product.
-
Acommon cause of overheating is dust or lint inside the device. Make sure these deposits are removed regularly by unplugging the unit and vacuuming the vents and grilles, filters, if available.
-
Do not use this device in a window as rain may cause electric shock.
-
Do not connect the appliance to a power source until it has been installed in its final position and placed in the position for use.
-
It is not recommended to use an extension cord with this device.
-
Do not place the cord under carpets, rugs, rugs, etc. Keep the cord away from places where it may trip over it.
-
Do not use this device with a programmer, timer or any other device that automatically turns on the heater as there is a risk of fire if the device is covered or placed incorrectly.
-
To avoid the danger of inadvertently resetting the thermal cutout, this appliance must not be powered by an external switching device, such as a clock, or connected to a circuit that is regularly turned on and off by the mains.
-
Do not get the device wet. If the device falls into water, disconnect the plug from the socket immediately. Do not put your hands into the water when the device is plugged in. Before reuse, it must be checked by an authorized service center.
-
The device should be switched off whenever you put it down.
-
Never turn on the device when the tank is not filled with water.
-
Use only clean, cool water.
-
Do not pour water into the tank above the maximum level.
-
Do not submerge the base of the device.
-
Do not add any chemicals to the tank, base or steam outlet. Do not add aromatic oils, salt, descaling tablets, powders or cleaning agents to the water.
-
The filler cap / water tank cover should always be screwed on / closed at all times.
-
Take care that the humidifier’s water mist outlet does not point directly towards walls, furniture, electrical outlets, electrical and electronic devices, and children. Too much humidity in the room can lead to a build-up of moisture, causing the growth of bacteria and fungi and damaging walls, furniture and wallpaper.
-
Do not block ventilation of the device. Keep a distance of at least 100 cm from the device. Do not block the water mist outlet with the humidifier function.
-
Do not use the device where there is a risk of condensation. Moisture can form on the inside and outside of the appliance when:
– the device is moved from a cold to a warm place,
– the heating system has just been turned on,
– the device is used in a room with high humidity,
– the device is cooled by the air conditioning cooling system.
When moisture condensation occurs in the device, it may not work properly or, in extreme cases, may be damaged. In this case, do not use the device and leave it to dry for several hours. -
Do not tilt, fall over or try to refill or pour water from the device while it is working.
-
Do not remove the reservoir from the base of the device while the humidifier function is operating.
-
Afilled water tank is heavy. When carrying it, keep it underneath as well.
-
Do not use the device if there is a water leak.
-
Do not leave water in the tank when the machine is not in use.
-
Clean the humidifier after each use cycle of the device. Follow the cleaning instructions in this manual.
-
Never allow sediment, moisture or water to remain in the tank (this can cause contamination or even damage the ultrasonic atomizer).
-
During long-term operation of the device, water mist emitted by the humidifier may fall to the floor and cause moisture.
WARNING: Do not use this heater in small rooms where there are people who are
unable to leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains, or other
flammable materials at least 1 m away from the heater air outlet.
“Caution hot surface” – The temperature of the accessible surfaces may be
higher during operation, which means that the
housing elements get hot during operation during operation. CAUTION !!!
NOTE: To avoid overheating – do not cover the heater. Do not cover the device with clothes, blankets or other textiles that may cause ignition.
Do not use the device near water, e.g. in a shower, bathtub or over a washbasin with water.
MONTAGE
The base (10) montage: Align the four fixing screw holes of the base (10) with the screw posts of the base (10), and screw with four self tapping screws to put the product into use. Look at figure 2.
PRODUCTDESCRIPTION (Figure 1)
- Humidifed air outlet
- Front display panel
- Air outlet
- Housing
- Air inlet
- Back cover
- Drain cover
- Top panels
- Drain plug
- The base
- Remote control
- Power switch
TOPPANEL& FRONTPANEL& REMOTE CONTROLMARKING – Figure 3
A. Standby button
A1. Fan function indicator
B. Timer button
B1.Timer indicator
B2.Timer / Temperature / Cooling down count down indicator
C. Timer / Temperature increase button
D. Timer / Temperature decrease button
E. Heating level regulation button
E1. Low heating level indicator
E2. High heating level indicator
F. Oscillation button
G. Humidifier function button
G1. Humidifier indicator
H. Temperature unit indicator
USAGE
-
Power on: Place the device on a stable floor and insert the plug into socket. Turn on the power switch (12) on the back of the product. “I” means switched on, “0” means off. At this time, the device is in standby mode, the display shows ambient temperature (B2), and the temperature unit indicator (H) will light on.
-
Fan
Press the button (A), the indicator (A1) will light up and the fan is operating (flow the air in room temperature). -
Heating
Press the button (E) once for low-level heating 1400W, the display lights up indicator (E1).
Press the button (E) twice for high-level heating 2200W, the display will light both indicators (E1 + E2).
Press the button (E) again to cancel the heating.
TIMER function: Press the button (B) repeatedly to set a period after which the device will turn itself off (between 1.0 hour – 12.0 hours, in steps of 60 minutes). At the same time timer indicator (B1) light display
OSCILLATION function: Press button (F) to activate oscillation, the device will swing to the right and left to distribute the exhaust air evenly. Press again button (F) to cancel oscillation function.
TEMPERATURE ADJUSTMENT
Adjust room temperature by pressing button (D) or (C). The default setting
temperature is 25°C. Temperature range from 10-35°C. Pres the button (D) to
increase the desired temperature and press the button (C) to decrease the
desired temperature. The device is intelligently programmed, it selects the
working level between low or high heat according to the desired temperature
and present ambient temperature.
HUMIDIFICATION FUNCTION
At first pour the water to water tank (13) according to instruction described
below. To pour the water to water tank (13), unplug the device at
first. Next press down and pull outside the protrude part on the back cover
(6) – look at figure 4. Take out the water tank (13) from the housing,
unscrew the plug of water tank (13) counterclockwise, pour clean water (no
essential oils added) and screw the plug tightly. Put the water tank
(13) inside the housing. Set the cover properly on two latches places well and
push it to close. The humidifying function can be used normally. Plug in the
device. Press the button (G), the product turns on the humidification
function, the humidification indicator (G1) lights up. Press the button (G)
again to turn off the humidification function, at the same time the
humidification indicator (G1) will be off. The humidification function can
also be used separately when fan / heating function is switch off but power is
on.
To drain the water out open the drain cover (7) pull the drain plug (9) and
drain the reminding water to suitable tank. When the device is not used for a
long time, the water in the tank should be drained.
Applicable environment conditions for the device operation:
– heating function use temperature in range from -20°C to 25°C.
– humidifier function use in temperature in range from 5°C to 40°C and the
relative humidity less than 80%.
To turn off the device press the button (A) again. Then, the fan will cool down the heating element inside the housing during 30 seconds, next the fan will automatic turn off. If the device is not set on heating function before, it will go directly to standby
Lighting off of the front display panel (2): After the device is working for 10 minutes, it will automatically enter the light off screen mode, press any key to light up the screen.
Remote control: Before using the remote control (11), take away the plastic foil piece on the right side of the remote control. Remote control operation is same as hand operation of top panel (8).
HOW TO CHANGE THE REMOTE CONTROLS BATTERY:
- The battery cover can be opened with a coin or the like.
- Install the button battery, pay attention to the battery polarity (“+” face up and “-” face down).
- Cover the battery cover.
CLEANING AND MAINTENANCE
- Make sure the device is not hot.
- Before cleaning the device remove the plug from the electrical socket.
- Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings.
- Clean the housing using only dry or moist cloth.
- Do not immerse the device in water!
TECHNICALDATA:
Power: 2200W
Power supply: 220-240V~ 50Hz
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>