Dowellin Toys Factory DRW351MG RC Drone Instruction Manual

Instructions for use

Transmitter Functions

Transmitter Installation

Note: Always pay dose attention to battery polarity to ensure they are fitted correctly.

Charging the Drone Battery

The drone’s battery must be charged before it can be flown. To avoid the risk of injury or damage. be sure the drone and remote control are both powered OFF and remove the battery from the drone when charging. The charging bine is approximately 80-90 minutes. Charge fully before use for best performance. Connect the USB charging cable (included) to the USB port of a powered ON computer or USB power adapter (not included), then connect the charging plug to the battery plug_ While charging, the light will display a red light. When charging is complete, the charger light will turn OFF.

Note:
Be sure to correctly match the plug to the charging port or damage may occur. Do not charge overnight. Do not leave unattended while charging.
When the drone’s battery is low power, the LED lights on the drone will begin blinking fast, indicating that it just has the 40s left to fly At this time, you need to fly it to the safe area and press down the one key landing button to land it If you fly it till it runs out of battery it will drop out of the sky.

Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed in the household trash_Please contact a local environmental or waste agency or the supplier of your model or your nearest Li-Po battery recycling center.

Flight Safety Information

Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airports, or bodies of water.
Do not fly near strong electromagnetic sources such as power lines and those base stations as it may affect the onboard compass.

Do not use the drone in adverse weather conditions such as rainy, snowy, foggy, and windy days.

Stay away from the rotating propellers and motors.

|

No-Fly Zone

---|---

Do not use the drone in adverse weather conditions such as rainy, snowy, foggy, and windy conditions.
The basic flight guidelines are important for pilots’ safety and the surroundings Please read the safety guidelines carefully.

Get Your Drone Ready

-Rotating propellers can be dangerous Do not start the motor when there are people nearby. -If the motor is still spinning, always keep your hands on the transmitter.

Pair the Drone

① Power on re crone and place t on a flat surface. The lights on the drone will blink as it searches for a signal from the transmitter. Be sure the head facing forward and the tail facing toward the pilot

② Turn on the transmitter. push the left control stick fully forward. wart for a Di to sound, then put the stick fully rearward, and wait for a second DE and the blink mode changed when the transmitter and the drone have paired successfully

Calibrate the Gyro

③After paring, pull down and to the right on both control sticks for 2-3 seconds When you hear Di and the lights on the drone blink fast ‘or 2-3 seconds. calibration is completed. (To ens..re a stable flight, after paring the drone and after a crash, we recommend the plot calibrate the gyro Do not attempt to do this while flying).

Flight Controls

Push the left control stick up or down and the drone will rise or fall.| Push up or down on the right control stick and the drone will fly forward or backward.

Push the left control stick left or right and the drone w II rotate to the left or to the right.| Push the right control stick left or right and the drone will fly to the left or to the right.

Setting Trim & Countering Drift

If the drone keeps drifting leftwards when hovering, press the right side-fly trimmer to adjust until it gets balanced.| If the drone keeps drifting rightwards when hovering, press the left side-fly trimmer to adjust until it gets balanced.

If the drone keeps flying backward when hovering, press the forward trimmer to adjust until it gets balanced| If the drone keeps flying forwards when hovering, press the backward trimmer to adjust until it gets balanced.

Even after the drone is calibrated. it may show a tendency to drift while airborne. Adjusting the trim will help counter this effect and allow better control of the drone But it will not entirely eliminate it. Air currents and other factors may still cause slight drift while time.

Speed Setting

Press the Speed button on the remote to change the drone’s speed.

• Low: Provides smooth and predictable control of the drone. The remote a II chine once to indicate the low-speed setting.
• Medium: The drone will move and respond faster to all control inputs The remote will chime twice to indicate the medium speed setting.
• High: Highest setting for maximum performance. The remote will chine three times to indicate the high-speed setting_

Note: The 3-speed modes can only be cyclically changed in this order: low-speed medium speed -high speed – low speed.

3D Flip Mode

Before attempting a flip, be sure that there is enough clear space around tr e crone ideally 9-10 ft. in all directions. It is not recommended to attempt to flip around or through any obstacles. as this may result in unintended damage.
Press the Flip button to activate Flip Mode, then move the Right Control Stick in any direction and the drone will perform a flip in the same direction_ Press the Flip button again to deactivate without performing a flip.

Caution: the drone will perform these maneuvers best with a fully charged battery.

Headless Mode

NOTE: Do not use the Headless Mode until you totally comprehend the instructions For Use.
Flying in Headless Mode without sufficient experience might result in loss or damage to the device.

1. Place the crone in 4ont of the pilot before pairing the crone to the transmitter. Make sure the head of the drone faces forward arc the to faces toward the pilot
2. After pairing arc calibration, press the Headless Mode button to enter the Headless Mode functor A beep will be heard from the transmitter, and the led lights will slowly %stk. indicates that crone is in headless mode.
3. Press the headless mode button again, and you will hear a beep which indicates the drone ex ts the headless mode.
4. Under Headless Mode. the forward direction is the direction the plot faces when the plot pars the drone with the transmitter.

Please make sure the pilot stays in the same orientation as the drone head faces when the drone takes off.
It is very important that the pilot does not change the direction or orientation he or she faces, otherwise, the drone and transmitter will lose connection, causing controls to not perform as desired.
Please use the Headless Mode function after you totally comprehend these functions; otherwise, it may result in the loss and/or damage of the drone.

Trouble Shooting

PROBLEM| POSSIBLE CAUSES|

SOLUTION

---|---|---
The drone does not respond to controls.| • No paver to remote or drone.
• Pox contact be4ween power plugs
• drone is out of range.| • Check remote batteries, replace 1
needed_
• Check the drone battery, be sure it is fully charged.
• Be sure the power plugs are firmly connected.
• Be sure the remote has an unobstructed Ire of sir to the drone.
• Remain Mho the remote’s 101I8. range.
The drone is difficult to control or flies erratically.| • Gyroscopes may
be misaligned| • Power OFF remote and
crone and reconnect
Drone drifts while in flight.| • Thin- -cit set or needs adjustment| • Adjust turn settings
The drone suffers from mechanical trouble.| • Damage to cozy, propellers, or other major components| • Repair or replace prat as needed.
LED lights are ON but the drone does not respond to controls.| • Low battery power| • Recharge the tottery.

PRECAUTIONS

1. The remote-control distance will be shortened when the power of the drone transmitter is insufficient.
2. When the power of the drone is Sinsufficient, the drone would have trouble taking off or be unable to fly high.
3. Please repair the drone in time when it is damaged. Don’t fly the drone when it is seriously damaged(rotor-wing breakage), or it might lead to injury.
4. Please remove the batteries or avoid the damage to the product caused by batteries leakage if you do not use the drone transmitter for a long time.
5. Don’t crash the drone from a high altitude or crash it seriously, or might shorten its lifetime.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>