Polk Audio MM522 Car Audio Speakers Instruction Guide
- June 3, 2024
- Polk Audio
Table of Contents
Polk Audio MM522 Car Audio Speakers
WIRING DIAGRAMS
Basic Coaxial Connection
MOUNTING DIAGRAMS
Crossover mounting allows for proper ventilation. Tweeter Attenuation Switch located outside crossover box, move to desired tweeter level setting.
INSTALLING
FLUSH MOUNT TWEETER MOUNTING
- Check for proper clearance: The flush mount kit is 1” (26mm) deep.
- Mark the center of the spot and cut a 2” (50.8mm) diameter hole using a hole saw, drill bit or razor knife.
- Assemble the cup, clamp and machine screw loosely as shown.
- Route wires through the round opening in the bottom of the cup.
- Press the assembly into the 2” (50.8mm) diameter hole until the clamp edge is below the mounting surface, then tighten the screw. The legs of the clamp can be bent outward by inserting a screwdriver through the holes in the cup while still mounted.
- Connect wires from the tweeter terminals of the Crossover to the tweeter itself using the faston connectors. Connect the red wire from the (+) terminal of the Crossover tweeter output to the red (+) wire from the tweeter.
- Mount the tweeter by snapping it into the mounting cup.
SURFACE MOUNT TWEETER MOUNTING
- Using the base of the surface mount cup as a template, mark the screw hole and drill them using a 1/8” (3mm) drill bit. Drill a second hole (for the speaker wire) using a 3/16” (5mm) drill bit.
- Screw surface mount cup to the panel.
- Push the tweeter wires through the open area at the bottom of the cup and through the 3/16” (5mm) hole in the panel.
- Connect wires from the tweeter terminals of the Crossover to the tweeter wires using fast on connectors. Be sure to connect the red wire strand from the tweeter to the (+) terminal of the crossover tweeter output.
- Mount the tweeter by snapping it into the mounting cup.
COAXIAL AND COMPONENT SYSTEMS SPECIFICATIONS
GETTING STARTED
Please inspect your loudspeakers carefully. Notify your Polk dealer if you notice any damage or missing items. Keep the carton and packing material; this will do the best job of protecting your loudspeakers if they must be transported.
Safe Limits of Operation
Damage to loudspeakers can occur when an amplifier, regardless of its wattage, is made to play at higher listening levels than it can produce at low distortion levels. This is usually beyond the “noon or 1 o’clock” position on the volume control. Operation at this level can result in very high levels of audible distortion originating in the amplifier, which can add a harsh, gritty sound to your listening material. Contrary to popular belief, a loudspeaker is more likely to be damaged by trying to get too much volume from a low-powered amplifier or receiver than from a high-powered one.
Technical Assistance or Service
If, after following the hookup directions, you experience difficulty, please double-check all wire connections. Should you isolate the problem to the loudspeaker, contact the authorized Polk dealer where you made your purchase, or contact Polk Customer Service 800-377-7655 (M-F, 9-5:30 EST, US only) or via email polkcs@polkaudio.com. Outside the US, call 410-358-3600. More detailed information—including audio how-to articles, FAQs, and online manuals—is available on our website www.polkaudio.com.
PRODUCT DISPOSAL – Certain international, national and/or local laws and/or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Importer/Distributor in your country. A listing of Polk Importer/Distributors can be found on the Polk website www.polkaudio.com or by contacting Polk at 1 Viper Way, Vista, California 92081 USA— Phone: +1 800-377-7655
LIMITED WARRANTY
Polk Audio, Inc. warrants the original purchaser only that this product will
be free from defects in materials and workmanship for a period of (1) one year
from the date of original retail purchase from a Polk Authorized Dealer.
However, this warranty will automatically terminate prior to the expiration of
the (1) one year period if the original retail purchaser sells or otherwise
transfers the product to any other party. The original retail purchaser shall
herein after be referred to as “you.” To allow Polk to offer the best possible
warranty service, please fill out the Product Registration Card(s) and send
them to the factory at the address provided in the Registration Card within
(10) ten days of the date of purchase. Defective products must be shipped,
together with a proof of purchase, prepaid insured to the Authorized
Polk Dealer from whom you purchased the Product, or to 1 Viper Way, Vista,
California 92081. Products must be shipped in the original shipping container
or its equivalent; in any case the risk of loss or damage in transit is to be
borne by you.
If, upon examination at the factory or Polk Authorized Dealer it is determined
that the unit was defective in materials or workmanship at any time during the
Warranty period, Polk or the Polk Dealer will, at its option, repair or
replace this product at no additional charge, except as set forth below. All
replaced parts and products become property of Polk. Products replaced or
repaired under this warranty will be returned to you, within a reasonable
time, freight prepaid.
This warranty does not include service or parts to repair damage caused by
accident, disaster, misuse, abuse, negligence, inadequate packing or shipping
procedures, commercial use, voltage inputs in excess of the rated maximum of
the unit, cosmetic appearance of the cabinetry not directly attributable to
defects in materials or workmanship, or service, repair, or modifications of
the Product which has not been authorized or approved by Polk. This warranty
is in lieu of all other expressed warranties.
If this product is defective in materials and workmanship as warranted above,
your sole remedy shall be repair or replacement as provided above. In no event
will Polk Audio, Inc. be liable to you for any incidental or consequential
damages arising out of the use or inability to use the product, even if Polk
Audio, Inc. or a Polk Dealer has been advised of the possibility of such
damages, or any other claim by any other party. Some states do not allow the
exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply to you. This warranty gives you specific legal rights
which may vary from state to state.
This warranty applies only to products purchased in the United States of
America, its possessions, and U.S. and NATO armed forces exchanges and audio
clubs. The warranty terms and conditions applicable to products purchased in
other countries are available from the Polk Authorized Distributors in such
countries.
FAQs
What is the outside to outside diameter of the speaker?****
There were no OD-related standards to be found. However, if you’re attempting to fit these in, they fit perfectly in a Harley. If not, almost every 6.5″ speaker application should be compatible with them.
Do vehicle speakers function in boats?****
People frequently ask us if our car speakers work on a boat. Despite the fact that the answer is technically correct, we always suggest buying genuine marine grade speakers for a number of reasons.
Can regular speakers be installed on a boat?****
Again, the quick response is “yes,” but we don’t suggest it. If you want to put some used (or new) automobile speakers in your boat, be ready to swap them out frequently.
How much power do my Polk Audio MM522 boat speakers require?****
Look for speakers with a top RMS rating of at least 50 watts RMS to complement the amp. If you have a bigger boat or just like loud music, look for an amplifier with at least 75 watts RMS per channel.
What distinguishes automobile audio from marine audio?****
Marine speakers are undeniably more robust than automobile speakers because they were made to survive salt corrosion and tough surroundings. Because they are not exposed to damp and sunlight, car speakers don’t normally need to be as durable.
What is a two-way maritime Polk Audio MM522 speaker?****
Two-way, or coaxial, speakers contain a separate tweeter located inside the woofer in order to handle the high frequencies and faithfully recreate the sound range of your music. Three-way, or triaxial, speakers combine a midrange driver with a separate woofer and tweeter for increased depth and realism.
Can Polk Audio MM522 marine speakers get wet?****
Marine surroundings can withstand products that are Marine Rated or Marine Grade. Marine grade parts can be exposed to rain, wind, and the sun (although not necessarily submersion). When a little water is splashed on them, they won’t burn because they can survive high ambient temperatures.
Are waterproof Polk Audio MM522 boat speakers required?****
First, they need to be durable and waterproof. Boat speakers must be able to withstand bad weather.
Do Polk Audio MM522 marine speakers require an amplifier?****
Amplification is a common feature of marine stereos, some of which are very potent. It is definitely possible to produce good sound without an external amplifier. Most individuals should test their stereo without an amplifier first as you can usually install one later.
What are the applications for Polk Audio MM522 marine speakers?****
The marine audio system, which is used to play music on boats, consists of a number of speakers, amplifiers, and other gadgets.
Why are Polk Audio MM522 Marine speakers good?****
The majority of maritime speakers are exceptionally strong and long-lasting. Make sure the speakers you buy are of excellent quality, resistant to rust and corrosion, and well-built. Look for speakers with plastic cones, such as those with polypropylene and neoprene rubber surrounds, for effective weather protection.
What distinguishes a marine speaker from a standard speaker?****
The speakers that are best suited for usage in water are known as marine speakers. They are frequently water-resistant in addition to being more robust. The different exposures to moisture, climate, and weather are what marine speakers are made to withstand.
How are Polk Audio MM522 marine speakers protected?****
For the best defence, we suggest getting single barrel speaker covers or double barrel speaker covers. These speaker covers won’t block sound because they are constructed of outdoor poly fabric, which is three times thicker than the majority of speaker covers.
Polk Audio MM522 marine speakers: where do they go?****
You should always put your full range speakers as high as possible for the best sound quality. Don’t mount them under seats or by your feet. On larger vessels and other places where it is feasible, you should consider putting speakers over your head. Subwoofers, on the other hand, are the complete opposite.
What exactly are marine-grade Polk Audio MM522 speakers?****
Due to the fact that they are designed expressly to withstand the outdoors and water, marine speakers are more than just speakers in a particular colour. Marine speakers are the best option for sound systems on boats because they can withstand the salt, water, and temperature variations that are common on the water.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>