SONOFF BASICR4 WiFi Smart Switch User Guide
- June 12, 2024
- SonOFF
Table of Contents
BASICR4 WiFi Smart Switch
User Guide
Quick Guide V1.0
Wi-Fi Smart Switch
BASICR4 WiFi Smart Switch
Power off
**** Please install and maintain the device by a professional electrician.
To avoid electric shock hazard, do not operate any connection or contact the
terminal connector while the device is powered on!
Wiring instruction
****
Wiring: 16-18AWG SOL/STR copper conductor only, Tightening torque: 3.5 lb-in
Make sure all wires are connected correctly.
Download the eWeLink App
Download the eWeLink App.
Power on
After
powering on, the device will enter the Pairing Mode during the first use. The
Wi-Fi LED indicator changes in a cycle of two short and one long flash and
release.
**** The device will exit the Pairing Mode if not paired within 10mins. If
you want to enter this mode, please long press button for about 5s until the
Wi-Fi LED indicator changes in a cycle of two short and one long flash and
release.
Scan QR Code to Add device
Open the
eWeLink App and scan the QR code on the device, then follow the instructions
given by the app to proceed.
Note: If the page doesn’t display after scanning the code, please power
on the device and then click the button in the top right corner of the eWaink
App homepage. Select ‘Add Device’ to proceed.
User Manual
https://sonoff.tech/usermanuals
Scan the QR code or visit the website to learn about the detailed user manual
and help.
FCC compliance statement
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including Interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver:
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003(B). This device
complies with RSS-247 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
ISED Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body. This transmitter
must not be co-located or operating inconjunction with any other antenna or
transmitter.
To ensure the safety of your electrical installation, it’s essential either a
Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker
(RCBO) with an electrical rating of 10A has been installed before the BASICR4.
WEEE Warning
WEEE Disposal and Recycling Information All products bearing this symbol
arewaste electrical and electronic equipment (WEEEas in directive
2012/19/EU)which should not be mixed with unsorted householdwaste. Instead,
you shouldprotect human health and the environment by handingover your waste
equipment to a designated collection point for the recycling of waste
electricaland electronic equipment appointed by the government or local
authorities. Correct disposaland recycling will help prevent potential
negative consequences to the environment and human health. Please contact the
installer or local authorities for more information about thelocation as well
as terms and conditions of such collection points.
SAR Warning
Under normal use of condition, this equipment should be kept a separation
distance of at least 20 cm between the antenna and the body of the user.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type BASICR4 is in compliance with Directive 2014/ 53/EU.The full
text of the EU declaration of conformity is available at the following intemet
address:
https://sonoff.tech/usermanuals
EU Operating Frequency Range:
Wi-Fi:802.11 b/g/n20 2412-2472 MHZ ; 802.11 n40: 2422-2462 MHz BLE: 2402-2480
MHz
EU Output Power:
Wi-Fi 2.46520dBrn ; BLE513dBrn
Shenzhen Sonoff Technologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
ZIP code: 518000
Website: sonoff.tech
Service email: support@itead.cc
MADE IN CHINA 
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>