MARMITEK RJ45 MegaView 91 Network Cable User Manual
- June 5, 2024
- MARMITEK
Table of Contents
MARMITEK RJ45 MegaView 91 Network Cable User Manual
SAFETY WARNINGS
- To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture. Do not use the product close to a bath, swimming pool etc.
- Do not expose the components of your systems to extremely high temperatures or bright light sources.
- Do not place the product in an enclosed space, such as a TV cabinet or equivalent. Provide adequate ventilation to ensure that the product is functioning properly and to protect against overheating.
- In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire. Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. Marmitek does not accept responsibility for additional damage other than covered by the legal product responsibility.
- This product is not a toy. Keep out of reach of children.
- Do not open the product: the device may contain live parts. The product should only be repaired or serviced by a qualified expert.
- Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on the identification tags. Never connect an adapter or power cord when it is damaged. In that case, contact your supplier.
1. INTRODUCTION
Congratulations on your purchase of the Marmitek MegaView 91TM! The MegaView
91TM provides a simple way to extend an HDMI (High Definition Multimedia
Interface) signal or DVI (Digital Visual Interface) over a single CAT5e/6
Ethernet cable. It even works on your existing home network (LAN) including
routers and switchers. The maximum CAT5e/6 cable length is 120 metres, at a
1080p resolution. Watch TV programmes, films and photos stored on, for
example, a digital TV decoder, Media Center PC, Blu-ray player or HDD recorder
located elsewhere in your home. Several receivers may simultaneously be
connected to the same network. The built-in loop-through function (HDMI out)
on the transmitter allows you to watch the same content on both your primary
HDTV and your secondary HDTV or HD projector (through the receiver).
All Marmitek products are manufactured with the utmost precision and are of
high quality. Please read this manual carefully and follow the instructions to
enjoy the possibilities of this product optimally.
2. PACKAGE CONTENTS
MegaView 91™
- 1x transmitter (HDMI Transmitter)
- 1x receiver (HDMI Receiver)
- 1x Infrared receiver
- 1x Infrared blaster LED
- 2x Power adapter
- 1x User manual
3. CAT5e/CAT6 CABLE REQUIREMENTS
- UTP-, FTP- or STP-cable
- 24AWG or lower
- Solid twisted pair
- 100 ohm at 1MHz
- RJ-45 jack according to EIA/TIA T568B standard
When the set is connected to a home network (LAN), Marmitek recommends the use of switchers and routers with Gigabit (1000Mbps) network ports for best performance.
Instead of CAT5e cable, CAT6 cable may also be applied (this offers better quality). Use a `solid twisted pair CAT-5e or CAT-6 cable’ in order to optimise transfer quality.
4. INSTALLATION
In order to check proper functioning of the system, it is advisable to test the set-up first, using a short CAT-5e/6 cable.
-
Switch off all appliances before you start connecting.
-
Connect the HDMI source (Blu-ray disc player, TV Decoder, Media Centre PC, etc.) to the MegaView 91 transmitter [1], using an HDMI cable (not provided).
-
Optional: connect an HDTV to the MegaView 91TM transmitter [2] with an HDMI cable to HDMI OUT, to be able to continue to watch TV in this room.
-
Connect your HDTV or HD projector to the MegaView 91TM receiver [3] with an HDMI cable to HDMI OUT.
-
Use one CAT5e/6 Ethernet cable to connect the MegaView 91’s transmitter to the receiver [4].
• The MegaView 91TM can either be connected by using a single cable, or through an existing home network (LAN) in combination with network switches and routers. -
Repeat steps 4 and 5 to connect additional receivers.
-
Connect the power adapter [5] to the `5VDC’ connection on the MegaView 91TM and plug the adapters into a socket.
Attention! Do not place the MegaView 91TM transmitter or receiver in an enclosed space, such as a TV cabinet or equivalent. Provide adequate ventilation to ensure that the product is functioning properly and to protect against overheating.
5. INSTALLATION IR RETURN
The MegaView 91TM has a built-in “infrared return channel”, which allows you to operate the connected device from another room or through closed cabinet doors using your own remote control.
-
Connect the IR receiver to the MegaView 91TM receiver [6].
• Position it so that it is visible to your (infrared) remote control, allowing it to receive the transmitted commands (up to 6 metres).
• The most logical place for the IR receiver is in the vicinity of your display device (HDTV or projector).
• By using the supplied adhesive strip, placement is possible virtually anywhere.
• Experiment to find the right position before definitive attachment of the IR receiver.
Attention! The adhesive strip may cause discolouration on certain surfaces, or may leave adhesive residue when removed. -
Connect the IR extender cable to the MegaView 91TM transmitter [7].
• Stick the IR blaster LED near the HDMI source.
• When positioned correctly, one blaster LED can operate all A/V devices within the same compartment of a cabinet.
• Experiment to find the right position before definitive attachment of the IR blaster LED.
Attention! The adhesive strip may cause discolouration on certain surfaces, or may leave adhesive residue when removed.
6. USAGE
- Switch on the HDMI source (e.g. TV Decoder or Media Centre PC).
- Switch on the display device (for instance HDTV or projector) and select the appropriate input. Usually you will do this by pressing the A/V or EXT button of your remote control.
- You will receive images from the connected A/V device immediately.
- The MegaView 91TM can also be used to operate the HDMI source from another room, by pointing your own remote control at the IR receiver and pressing a button.
- When everything is working normally, the ‘DATA’ LED on the receiver will flash rapidly and the ‘LINK’ LED will light up continuously.
7. FREQUENTLY ASKED QUESTIONS
Bad (or no) image and sound
- Please check that the HDMI source is on.
- Use only CAT5e/CAT6 cable as specified in chapter 3 (CAT5e Cable Requirements).
- Check if the CAT5e/CAT6 cable provides a solid connection (no cable faults).
- Check if the RJ-45 has been connected according to the EIA/TIA T568B standard.
- Please ensure that the maximum cable length is not exceeded.
- Install your system as far away from any RF sources (wireless devices) as possible.
- Set a low resolution on your HDMI source. The CAT5e/6 cable used probably cannot deal with the higher resolution bandwidth.
The screen will display the text “Waiting for connection”
- When both the
’LINK” and’DATA” LEDs are not lit on the receiver, check the cable connections to the transmitter and the sender. - When the transmitter and receiver are connected through a network (with routers / switchers), and the “DATA” LED is slowly blinking on the receiver, check the cable connection between the transmitter and the network.
The screen will display the text `’Please check the TX input signal”
- Please check that the HDMI source is on.
Do you have any questions that are not answered above? Please check www.marmitek.com.
8. TECHNICAL INFORMATION
Specifications may change without prior notice.
9. OPTIONALLY AVAILABLE
Connecting multiple devices
To connect multiple AV devices to your TV with only one cable or to transmit
the signal of multiple AV devices to your TV, you can you can choose from a
wide range of active switchers. More information about these so called HDMI
Switchers can be found at www.marmitek.com
Additional receiver
An additional receiver can be used to connect multiple HDTVs or HD projectors
simultaneously to the same network.
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this
symbol on the product and/or its packaging must not be disposed of with
unsorted municipal waste. The symbol indicates that this product should be
disposed of separately from regular household waste streams. It is your
responsibility to dispose of this and other electric and electronic equipment
via designated collection facilities appointed by the government or local
authorities. Correct disposal and recycling will help prevent potential
negative consequences to the environment and human health. For more detailed
information about the disposal of your old equipment, please contact your
local authorities, waste disposal service,
MegaViewo9r1tBhaecksUhseormpawnuhael_r1e24yx1o7u6_pTVu&rcvihdaeos.peddf t1he7
-1p1r-o20d1u9 c1t3.:48:47
DECLARATION OF CONFORMITY
Hereby, Marmitek BV, declares that this MegaView 91TM is in compliance with
the essential requirements and other relevant provisions of the following
Directives: Directive 2004/108/ec of the European parliament and of the
council of 15 December 2004 on the approximation of the laws of the Member
States relating to electromagnetic compatibility Directive 2006/95/EC of the
European Parliament and of the Council of 12 December 2006 on the
harmonisation of the laws of Member States relating to electrical equipment
designed for use within certain voltage limits Directive 2002/95/EC of the
European Parliament and of the Council of 27 January 2003 on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment Commission Regulation (EC) No 278/2009 of 6 April 2009 implementing
Directive 2005/32/EC of the European Parliament and of the Council with regard
to Ecodesign requirements for no-load condition electric power consumption and
average active efficiency of external power supplies
MARMITEK BV – P.O. BOX 4257 – 5604 EG EINDHOVEN THE NETHERLANDS
COPYRIGHTS
Marmitek is a trademark of Pattitude B.V.
MegaView 91TM is a trademark of Marmitek B.V. All rights reserved. Every
effort has been made to ensure that the information in this manual is
accurate. Marmitek is not responsible for printing or clerical errors.
Copyright and all other proprietary rights in the content (including but not
limited to model numbers, software, audio, video, text and photographs) rests
with Marmitek B.V. Any use of the Content, but without limitation,
distribution, reproduction, modification, display or transmission without the
prior written consent of Marmitek is strictly prohibited. All copyright and
other proprietary notices shall be retained on all reproductions. Other
company and product names mentioned herein may be trademarks of their
respective companies. Mention of third-party products is for informational
purposes only and constitutes neither an endorsement nor a recommendation.
Marmitek assumes no responsibility with regard to the performance or use of
these products.
20653/20191106 | MegaView 91™
all rights reserved © MARMITEK
stay connected marmitek.com
References
- Marmitek | Specialist for 25 years | Wireless HDMI & audio and Smart Home
- Marmitek | Al 25 jaar specialist in slimme oplossingen
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>