WAHL 9916-4301 Beard Cordless Rechargeable Facial Hair Trimmer Instruction Manual

WAHL 9916-4301 Beard Cordless Rechargeable Facial Hair Trimmer

Operating Instructions for Battery Trimmer Rechargeable and Rechargeable Cord/Cordless

3-YEAR LIMITED WARRANTY
Valid in U.S.A. Only
If your Wahl product fails to operate satisfactorily within three (3) years from the date of original purchase or receipt as a gift, Wahl will, at our option, repair or replace the product and return it to you FREE OF CHARGE. Do not return this product to store where purchased. Products needing repair under this warranty should be returned with postage pre-paid to the following address or call 1-800-767-9245 for assistance:
Wahl Clipper Corp.
Attn: Repair Department 3001 Locust Street Sterling, Illinois 61081
When mailing, please include a note describing the defect and the date of original purchase or receipt as a gift. Products out of warranty will be repaired at our standard repair charges.
This warranty does not cover products damaged by:

1. Modification or repair by anyone other than Wahl Clipper Corporation or a Wahl authorized service center;
2. Commercial (non-consumer) use or unreasonable use.
   This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No other written express warranty is given. No responsibility is assumed for incidental or consequential damages of any type or for the use of unauthorized attachments. Some states may not allow the exclusion or limitation of incidental or consequential damages, so the limitation may not apply to you. Warranty valid in U.S.A. only.
   Outside U.S.A., check with store for Wahl authorized distributor’s warranty.

For more information or Product Registration, visit WahlUSA.com

© 2018 Wahl Clipper Corporation
Part No. 93276-101
Printed in China

For Household Use Only

RECHARGING

1. This trimmer is conveniently designed for household use. It should be allowed to charge overnight before first use.
2. Remove the trimmer, recharging transformer and accessories from the packing material.
3. Connect the transformer to the trimmer. BE SURE TRIMMER IS IN THE “OFF – 0” POSITION WHEN CHARGING.
4. Plug the recharging transformer into any convenient electrical outlet at the correct voltage.
5. When trimmer is not in use, it may be connected to the transformer and plugged into an outlet to assure maximum power is available when it is next used. This transformer is designed to continuously charge the battery without overcharging.
6. Ni-Cad battery life may be extended with the following procedure: Once every month, let the trimmer run until the motor stops. Move the switch to the “OFF – 0” position and recharge fully overnight.
7. If you have a rechargeable cord/cordless trimmer, it can be used with the cord so you can trim even if the charge is low. The charging indicator light will glow when your trimmer is in the “OFF” position and connected to its charger. The trimmer cannot be overcharged, so you may charge it as often as desired. We recommend that the battery be “worked” or discharged by trimming without the cord and by not recharging after every use.

In certain areas that experience low line voltages, the red charging indicator light on your trimmer may become dim as the battery nears full charge. This dimming does not affect the performance of your trimmer but is simply a result of variances in power line voltages

TROUBLESHOOTING (RECHARGEABLE)

If your trimmer does not seem to take a charge, check the following before returning it for repair:

1. Check outlet current by plugging in another appliance.
2. Make sure the outlet simply is not connected to a light switch which turns the power at the outlet off when lights are turned off.
3. Be sure the trimmer is properly connected to the recharging transformer, all connections are secure and the switch on the trimmer is turned “OFF – 0.”
4. If your electricity is connected to a master power switch, we suggest the trimmer be disconnected from the charger anytime the master switch is off. Leaving the unit plugged into a dead outlet or an unplugged charger will drain the battery.
5. If trimmer does not run and it is completely charged, turn the unit “ON – I” and pinch or push the blades manually. (Oil may have dried out between the blades, so they may be temporarily stuck together.)

RECYCLE/REPLACEMENT OF NI-CAD BATTERY

CONTAINS SEALED, RECHARGEABLE NICKEL-CADMIUM BATTERY. MUST BE RECYCLED OR DISPOSED OF PROPERLY.

The RBRC Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery contained in this product indicates Wahl is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which is illegal in some areas. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Wahl’s involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cad, Ni-MH, etc.) batteries. Under normal use, the rechargeable nickel-cadmium batteries in your trimmer may last up to five years. At the end of their life, when they will no longer take a full charge, the nickel-cadmium batteries must be removed and recycled or disposed of properly. Do not attempt to replace the batteries. All servicing or battery replacement should be performed by an Authorized WAHL Service Location. To remove the battteries for recycling or disposal, follow these steps:

1. Unplug transformer from outlet, disconnect cord from trimmer and allow the batteries to completely run down before disassembly.
2. Using a screwdriver, pry the back grip pad away from the housing.
3. Turn trimmer over and repeat on the opposite side until the grip pad is loose.
4. Remove the back grip pad.
5. Remove the two screws.
6. Pull the trimmer apart.
7. Cut the wires and remove the two batteries.
8. Apply tape to both ends of the batteries before recycling or properly disposing.

LOADING / REPLACING BATTERIES (BATTERY UNIT ONLY)

1. Remove battery cover from front of trimmer by pushing in and back on the plastic door in the direction of the arrows.
2. Insert two AA batteries as indicated by molded outline in trimmer.
3. Replace battery cover to its original position.
4. Move switch to “ON” position to use.
5. To maximize battery life, trimmer should be shut “OFF” immediately after using.

TROUBLESHOOTING (BATTERY UNIT ONLY)
If your trimmer fails to operate when switched “ON,” check your batteries to see if they are properly installed. Positive end (center post) should be located as shown in battery housing. Make sure the switch is in the “ON” position and check to be sure blades are free to move. If blades become clogged with debris, manually pushing the blades back and forth a few times while unit is turned “OFF” may help free the blades + and allow the trimmer to operate.
If it still does not operate, your batteries have probably exceeded their useful life. To maximize battery life, replace both AA batteries at the same time.

CARING FOR YOUR TRIMMER

OILING BLADES
For best results, use Wahl Clipper Oil on the blades only when necessary, or approximately once a month. Motor bearings are permanently lubricated—do not attempt to oil.
When oiling your trimmer, turn the trimmer “ON – I,” hold the unit with the blades facing DOWN and squeeze three drops across the front of the blade and one drop on
each side on the heel of the blade.
Wipe off excess oil with soft cloth.

NOTICE—DO NOT OVER OIL!
Excessive oiling or application of
liquids will cause damage if allowed to seep back into motor.
BLADE CARE
Trimmer blades have precision-hardened, ground and lapped cutting teeth. Blades should be handled carefully and never bumped or used to cut dirty or abrasive material. Never rinse the blades with water, or the blades may rust. Clean with the included brush.

CLEANING/STORAGE
Before storing your trimmer, use the cleaning brush to whisk any loose hairs from the unit and the blades. For units with a soft-touch grip, use a damp cloth to wipe down the body of the trimmer, taking care not to get the blades wet. Store unit in such a manner so that blades are protected from damage.
When the trimmer is not in use, the trimmer blade guard attachment should be in place to protect the blades.
This appliance should be stored in a manner where it is not subjected to crushing, heating above 100°C (212°F), or incineration.

6-POSITION GUIDE makes achieving a consistent trim easy, every time.
The guide can be removed (providing a seventh cutting position) and reattached without changing the preset cutting length, so once you have found the perfect length, there’s no guesswork in achieving it every trim. The trimming guide is a two-piece assembly, consisting of a base and a comb. It should not be disassembled. To attach the guide, simply slide it on at a slight angle and press the release tab down to secure in position. To remove the guide, gently push up on the release tab and slide the assembly away from the trimmer. Adjust the trimming length by pressing on the thumb lever and moving the comb forward or backward to the desired setting.

GROWING A BEARD

There are three key factors that will determine which beard style is best for you:

1. The shape and dimensions of your face.
2. The natural growth of your beard.
3. The thickness of your beard.

If you are unsure about the type of beard that would most suit your face, speak with a professional hair stylist or go to WahlUSA.com.

TRIMMING AND EDGING YOUR BEARD
The following are suggested trimming steps and trimmer positions. You may find different procedures work better for you.

1. Comb your beard in the direction that it grows to help reveal stray hairs that may be longer than the others.

2. Attach the 6-position trimming guide to trim and taper your beard. With the blades pointing toward you, begin with the trimming guide attachment set at a long trimming length. For best results, start at each sideburn and stroke downward toward your neck. Trim toward your chin in smooth,overlapping strokes, following the lay of your beard. If you trim against the way your beard naturally lays, the trimmer will cut the hair much shorter and the result may be patchy.
   Adjust the trimming guide to progressively shorter settings until you reach the desired length of beard.
   You may wish to set the trimming guide attachment to cut closer near the ear and down under the chin, changing to a longer setting toward the front of the face and point of your chin.
   When the trimming guide is removed, it will remain at its last length setting until you change it.
   Always be sure the trimming guide is snapped solidly into the desired position before you start to trim.

3. Remove the trimming guide and cut the outline of your beard.
   Rotate the trimmer so that the blades are pointing toward you. Starting under your chin and working back toward your jawbone and ears, cut the outer perimeter of your beard underneath the jawbone. Continue the line all the way up to the ears and hairline.

4. Accentuate your beard line by using the trimmer in a downward motion.
   Start at the line you’ve created and, working from the chin back toward the ears, trim the area right under your beard line.

5. Define the upper part of your beard using the same technique.

6. For a neater finished look, use the close-trim/jawline blending attachment which is also included with your trimmer. To use the attachment, simply insert one side
   of the attachment over the front of the blades, and then push the other side back until both sides are locked into position. Then, using the trimmer in an upward motion, start trimming under the chin with short, outward, rolling strokes. Continue trimming until entire jawline is blended.

To remove the attachment, pull tab away from one side to release attachment from trimmer. Use somewhat of a rolling pressure action, with your thumb on top and index finger underneath.

TRIMMING YOUR MUSTACHE WITH BEARD REGULATOR

1. Comb your mustache.

2. Hold the trimmer in a vertical position with the blades pointing toward you in order to define the line of your mustache.

3. With the attachment set at a fairly long trimming length, begin trimming your mustache, starting at the top and working down to your upper lip. Use progressively closer settings to get the look and  length you desire. You may also use the close-trim/jawline blending attachment for finish blending and tapering your mustache.

4. For tapering the mustache, set the 6-position trimming guide at a medium length. Starting in the  middle of your mustache, follow the lip line  and taper with short upward strokes of the trimmer, working out toward the corners until a gentle shape is created on the bottom of your mustache.

5. As a finishing step, remove the trimming guide and, using only the bare blades, make a definitive line at the bottom of your mustache.

TRIMMING YOUR BEARD WITH ATTACHMENTS

Your trimmer includes three snap-on attachments, 1/8” and 3/16” and a stubble guide. The attachments are ideal for trimming and defining your beard, as well as for achieving a stubble look. The guides can be used with or against the direction of hair growth depending on your preference of closeness. For the stubble look, use the stubble guide every other day. The specially designed rounded guide will give you that few day growth look. Outline your stubble look like you would a beard.

SERVICE AND REPAIR
If you have problems with your trimmer, send it prepaid with a note explaining the problem to:
Wahl Clipper Corporation
Attn: Repair Department
3001 Locust Street
Sterling, IL 61081
Telephone 800-767-9245
For products purchased outside the United States, contact your distributor.
If for any reason within 60 days of purchase of your Wahl® trimmer you are not satisfied with your trimmer and would like a refund, just return your trimmer, together with the sales receipt, to the retailer from whom you purchased it. Wahl will reimburse all retailers who accept trimmers within 60 days of purchase. If you have any questions regarding this money-back guarantee, please call 1-800-767-9245 in the United States.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>