Nomadelic 23860 Solo 140 True Wireless ANC Earbuds User Manual
- June 5, 2024
- Nomadelic
Table of Contents
Nomadelic 23860 Solo 140 True Wireless ANC Earbuds
Overview
- Touch control surface
- Status indicator
- Reset button
- Microphone
Specifications
- Bluetooth: 5.1
- Playback time: 5 h+ 10 h
- Charging time: 2.5 h
- Noise reduction: 30 dB +3 dB
- Water resistant: Yes, IPX4
Use
Charge the case and earbuds fully before first use.
Power on/off
Take the earbuds out of the case to start the headset. Place the earbuds back
in the case to turn them off. Power the earbuds on manually by holding the
touch control surface for 2 seconds. Turn the earbuds off manually by holding
the touch control
Surface for 6 seconds. To save battery time, the earbuds automatically turn
off after 5 minutes of being Out of range from their Bluetooth device.
Pairing
Open the case and remove the earbuds. The earbuds connect automatically. Open the Bluetooth settings on your device and connect to “Nomadelic Solo 140”. Pairing occurs automatically after this each time the earbuds are removed from the case.
Charging
Connect the USB-C cable to the charging port on the case and a computer or a USB power adapter to charge the case. The status indicator on the case flashses to indicate the battery level. When the indicator turns to a solid red light, the case is fully charged. Put the earbuds in the case to charge them. The indicator on the case flashes every two seconds while charging. When the earbuds are fully charged the indicator turns off.
Control music and voice assistant
- Play/pause: Double-tap the right earbud.
- Next song: Triple-tap the right earbud.
- Previous song: Triple-tap the left earbud.
- ANC/hear through: Hold the touch control surface of the left or right earbud for 3 seconds.
- Voice assistant: Double-tap the left earbud to activate voice assistant. Tap once to turn it off. Note! For i0S only.
Control calls
- Answer a call: Tap the left or right earbucd.
- Hang up a call: Tap the left or right earbud.
- Reject a call: Hold the touch control surface of the left or right earbud for 1 second.
Reset
If the earbuds do not pair correctly, try to reset. Put the earbuds in the
case and open the case. Press and hold the Reset
button for 10 seconds. The status indicator flashes alternately twice. Take
the earbuds out of the case and hold the touch control surface for 10°
seconds. When the earbuds emit a tone, the reset is finished. Put the earbuds
back into the case and take them out again. The earbuds automatically pair
together, but you must reconnect them to your phone (repeat the steps under
the heading “Pairing”).
Troubleshooting
FAQ
Q1: Pairing fails.
- Put the earbuds back in the charging case and close the case cover.
- Take the earbuds out of the charging case. They enter pairing mode automatically. Choose “Nomadelic Solo 140” in your phone’s Bluetooth settings to pair.
- If the pairing still fails, check the following points:
- Make sure the earbuds and your Bluetooth device are next to each other or within 10 metres and that there are no obstacles between them.
- Make sure there are no signal interferences nearby (check the question “Connection is not stable” for signal interference conditions).
- Try to reboot your Bluetooth device or the earbuds.
Q2: I paired the earbuds with my phone before, but I failed to pair them
again.
Turn on Bluetooth in your phone and in “My devices’/”Paired devices”, choose
“Nomadelic Solo 14O”, tap “Forget This Device’. Then, pair the earbuds with
your phone again.
Q3: Conneotion is not stable.
Make sure that the Bluetooth conneotion distance is not more than 10 metres
and that there are no objects between the earbuds and your Bluetooth device,
or a radio or wifi signal that is interfering.
Q4: Power runs out fast.
The earbuds’ playtime varies depending on the volume level and audio content.
Put the earbuds back into the charging case after use to avoid unnecessary
power consumption.
Q5: The earbuds are reconnecting to my phone while being charged in the
case.
When the charging case is out of power during charging, the earbuds
automatically turn on and reconnect to the latest paired Bluetooth device. If
the earbuds are not paired with a Bluetooth device, they automatically turn
off after 5 minutes.
Safety information This product contains a rechargeable Li-Po battery and the
battery cannot be replaced. To prevent possible hearing damage, do not listen
at high volume levels for long periods of time.
Safety information
- This product contains a rechargeable Li-Po battery and the battery cannot be replaced.
- To prevent possible hearing damage, do not listen at high volume levels for long periods of time.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>